STEP 6 Align the Walk Belt ..............31 STEP 7 Adjust Walk Belt Tightness ............33 STEP 8 Install the Power Cord ............. 34 5. UNDERSTAND THE T635M DISPLAY ..........DISPLAY Overview ................DISPLAY Specifications ............... DISPLAY Windows ................36 DISPLAY Keys ..................
1. INTRODUCTION Congratulations on the purchase of a high quality SportsArt product, the T635M treadmill. Constructed of high quality materials and designed for years of reliable performance, this product was made for full commercial use. Before this product is assembled or operated, we recommend that you familiarize yourself with this manual.
2. SAfETy PRECAUTIONS This product was designed and built for optimum safety. However certain precau- tions apply during the use of this product. Please note the following safety precautions: • Please read the entire manual before assembly and operation. Make sure the product is installed and operated as instructed in this manual.
Page 5
2. SAfETy PRECAUTIONS (CONTINUED) CAUTION: If you feel any pain or any abnormal sensations, STOP YOUR WORKOUT and consult your physician immediately. Work within your recommended exercise level. DO NOT work to exhaustion. Before beginning any exercise program, you should consult with your doctor. It is recommended that you undergo a complete physical examination.
Page 6
2. CONSIGNES DE SÉCURITÉ IMPORTANTES Votre tapis de course SportsArt a été conçu et fabriqué afin d’assurer une sécurité optimale. Cependant certaines précautions s’appliquent chaque fois que vous uti- lisez votre tapis de course. • Lisez entièrement le manuel avant l’assemblage et l’utilisation. Veuillez aussi noter les consignes de sécurité...
Page 7
2. CONSIGNES DE SÉCURITÉ (SUITE) • Pour éviter de vous blesser, restez sur les bandes de repos (barres latérales) avant de démarrer le tapis de course. • Ce tapis de course n’est pas destiné à être utilisé par des personnes (y com- pris des enfants) dont les capacités physiques, sensorielles ou mentales sont réduites ou qui ne disposent pas de l’expérience ou du savoir nécessaires, sauf si celles-ci ont au préalable été...
3. LIST Of PARTS Assembly Parts Name Qty. Name Qty. A1 Display Hardware kit A2 Handlebar assembly A10 Power cord A3 Right pedestal A11 Front handlebar assembly Upper and lower right A4 Feeder cord A12-R connector covers Upper and lower left A5 Waterproof ring A12-L connector covers...
Page 9
3. LIST Of PARTS (CONTINUED) Components in the Hardware Kit Name Qty. Specification Notes Screw cover (curved) Screw cover (flat) Mushroom top self tapping M4*L16 screw Screw socket Spring clip 15A-100V-110V Fuse 10A-200V-220V L-shaped Allen wrench L-shaped Allen wrench L-shaped Allen wrench T-shaped Allen wrench Double open-end wrench 22*24...
4. ASSEMBLE THE PRODUCT Follow instructions below to assemble this product. Note that in this manual the words “left” and “right” are used to refer to the product and its parts. As such, these designations correspond to the “left” and “right” sides of a person in position to exercise on this product.
STEP 0 Preparation: Inspect Walk Belt Placement Inspect the position of the walk belt in relation to the guide rollers. The walk belt should be in the groove of the guide rollers (image √) as A shown. Make sure that the walk belt is not outside of the groove of the guide rollers (image X).
STEP 1 Install the Pedestals and Handlebar Assembly Follow instructions below to install the pedestals and handlebar assembly. The illustration below provides an overview of this step.
Page 13
STEP 1 Install the Pedestals and Handlebar Assy (Cont.) (a) First, remove screws (41) from pedestal mounts. (b) Next, inspect the spring clip (A) and screw socket (B) to see if they are in place still. If not, get them from the hardware kit and inset them in place.
Page 14
STEP 1 Install the Pedestals and Handlebar Assy (Cont.) Follow instructions (a) through (d) below to thread the data cable through the right pedestal. (a) Pull the cable from the right side of pedestal mount. Cut the zip tie on the data cable, and pull the cable straight and away from the pedestal mount as shown.
Page 15
STEP 1 Install the Pedestals and Handlebar Assy (Cont.) Hold the data cable at the top of the right pedestal (A3), and insert the bot- tom of the right pedestal (A3) onto the pedestal mount. Place the water guard (A5) on the pedestal higher than the motor cover. Repeat the process for the left pedestal (A7) assembly.
Page 16
STEP 1 Install the Pedestals and Handlebar Assy (Cont.) Follow steps (a) through (f) to install handlebar. (a) First, remove the screws (42) (43) from the handlebar assembly (A2). (b) Insert the left side of the handlebar (A2) into the left pedestal (A7). (c) Connect the cables in area A from the right pedestal (A3) and from the handlebar (A2) as shown.
Page 17
STEP 1 Install the Pedestals and Handlebar Assy (Cont.) (d) Tuck cables into the pedestal safely, and then insert the right side of the handlebar assembly (A2) into the right pedestal (A3), without pinching or crimping cables. (e) Thread screws (42) (43) in place by hand. First, secure the screws (42) in area B, and then secure the screws (43) in area C.
Page 18
STEP 1 Install the Pedestals and Handlebar Assy (Cont.) Follow steps (a) through (d) to install the front handlebar assembly. (a) Loosen and remove the screws (47) from the front handlebar assembly (A11). (b) Loosen the screws (46) from the front handlebar assembly (A11). Do not remove the screws.
Page 19
STEP 1 Install the Pedestals and Handlebar Assy (Cont.) (c) Connect the cables from the front handlebar assembly (A11) and from the handlebar assembly (A2). (d) Insert the front handlebar assembly (A11) into the handlebar assembly (A2) and secure with the screws (47) (46). (Note: Avoid pinching or crimping the cables.)
Page 20
STEP 1 Install the Pedestals and Handlebar Assy (Cont.) After the handlebars are in place, secure pedestal screws on left and right sides in area A. Put the pedestal covers (A6a) (A6b) in place and secure them with the screws (33). Finally, put the water guards (A5) in area B down against the motor cover on both sides.
Page 22
STEP 2 Install the Display (Continued) Follow steps (a) through (f) below to install the display assembly. (a) Remove the screws (44) from the handlebar assembly (A2). (b) Insert the display (A1) onto the handlebar assembly (A2). (Note: aim properly to avoid damaging the display board.) (c) Push the display (A1) slightly upward and then insert the display mounting bottom into the opening on the handlebar assembly.
Page 23
STEP 2 Install the Display (Continued) (d) Connect cables in areas A and B. (e) After connecting cables, tuck them away for safety, and then slightly lift the display (A1) and press it into place. (Note: in area C, the display cover must be outside of the handlebar cover.) (f) Hold the display (A1) forward slightly as shown and then press downward when securing screws (44).
Page 25
STEP 3 Install Long Handrails (Continued) First, remove the left and right end caps from the landing strip area. (See step #1 below.) Remove screw covers and screws from the landing strips and then remove landing strips from the product. (See step #2 below.)
Page 26
STEP 3 Install Long Handrails (Continued) Follow the illustrations below. First, Remove the screws and the supporting plate from the covers, (do not remove the screws (A) from the supporting plate). Then remove the screw from the inside middle of the upper cover. Finally, remove screws from the bottom part of the long handrail.
Page 27
STEP 3 Install Long Handrails (Continued) Align left and right long handrail supports in place, and secure them with screws. Note: do not yet fully secure these screws. Leave handrail supports slightly loose.
Page 28
STEP 3 Install Long Handrails (Continued) Set left and right long handrails in place on the handrail supports as shown. Use screws (a) (b) to secure the long handrails to the handle ends.
Page 29
STEP 3 Install Long Handrails (Continued) As shown: First, attach left/right side of “long handrail covers” to the left/right handrail assembly. Second, push the cover forward into place so the screws A of the supporting plate is aligned with the screw holes. Third, secure the top cover with screws.
STEP 5 Level the Treadmill 1. Press on points A and B to inspect whether the unit is stable and level on the ground. 2. If not, please level the treadmill by following instructions (a, b, c): (a) First, loosen the leveler nuts. (b) Adjust the leveler feet downward until the treadmill is level and does not rock.
STEP 6 Align the Walk Belt *Make adjustments as needed, but avoid turning rear roller screws more than one quarter rotation at a time. *See next page for the illustration provides an overview of this step. (a) First, make sure the treadmill is on a leveled surface and the incline is at (b) Start the speed at a lower rate of 3kph/2.5mph to check if the walk belt is aligned.
STEP 7 Adjust Walk Belt Tightness Walk belt tension is important to treadmill performance. As your foot hits the walk belt, does the walk belt stop sluggishly before regaining traction? Or, if you stomp your feet, bracing against the direction of rotation, does the walk belt not pause whatsoever? When either of these two conditions oc- curs, walk belt tension should be adjusted.
STEP 8 Install the Power Cord (a) First remove screws (45) from the power cord socket on the product. (b) Insert the power cord into place on the product. (c) Secure power cord connector screws (45) and then insert the other end of the power cord (A10) into the appropriate power supply socket in the wall.
5. UNDERSTAND THE T635M DISPLAy DISPLAy Overview The T635M display was designed to help people obtain their fitness goals simply and conveniently. Please familiarize yourself with the features of this display and thereby get optimum benefit and enjoyment from this product.
DISPLAy Specifications ● Speed (Forward): 0.1 to 10.0 mph or 0.2 to 16.0 kph ● Speed (Reverse): -0.1 to -3.0 mph or -0.2 to -5.0 kph ● Incline: 0% to 10%, in increments of 0.5% ● Time: 0:00 - 300:00 ●...
Page 38
DISPLAy Keys (Continued) HILL – Each time this key is pressed, the LED above the key will light up and one of three hill workouts will appear: HILL 1, HILL 2, HILL 3. RANDOM – Press this key to select one of an almost endless number of randomly generated workout programs.
“PRESS SPEED UP” will appear as a prompt to continue exercising. 6. OPERATE THE T635M LED TREADMILL There are two ways to start operating this product: (1) Press the QUICK START key, or (2) press the PROGRAM/GOAL SELECTION key to enter a preset program.
OPERATION Start a Workout Program To obtain more accurate calorie counts and target heart rates, operate the product via a workout program as follows: 1. Press a workout program key to select a workout or press a goal key (TIME, DISTANCE, CALORIES) to select a goal program.
OPERATION Display 1. If the feedback window is at bottom row, press SPEED▲/▼key to adjust the speed, the display will temporary switch to top row to show the adjustment. In 4 seconds, it will return to bottom row. Same thing will happen if it is displaying top row, and INCLINE ▲/▼key is pressed, it will temporary switch to bottom row.
OPERATION Energy Smart function This treadmill is built in with energy smart feature which is an energy con- servation function for when the treadmill is not in use. This feature can be activated in the basic setting and a timer can be set. When this feature is activated, the power will be shut off to run any control boards and electronic components in this treadmill.
Page 43
OPERATION Workout Programs (Continued) Once an Interval program is selected, it will enter user profile setting page. Age, weight, program time as well as Rest and Work segment setting. User can set both incline and speed for Rest and Work segments to customize the Interval program.
Page 44
OPERATION Workout Programs (Continued) • The fitness test is completed. • The user’s heart rate exceeds (220–AGE) * 0.8 for more than 15 seconds. • There is no heart rate signal for more than 30 seconds. At this point, the message screen shows “END OF FIT TEST” and “YOUR SCORE - XXX”, (where XXX represents a number from 0~100).
Page 45
OPERATION Workout Programs (Continued) f. During exercising, press SPEED ▲/▼ keys or numeric keys to change the max speed. • INCLINE control mode If incline is your preferred heart rate control variable, the incline position will automatically change to maintain your target heart rate. You can also press INCLINE ▲/▼...
OPERATION User Preference & Component Version User preference settings allow you to change default settings and review some historical data of this product. To access user preference settings, press the CHANGE DISPLAY key for 2 seconds during Banner page. ● Unit setting: the default unit is English. On the message window, “UNIT –...
OPERATION Error Messages Error messages can appear on this treadmill as a troubleshooting aid. Error messages appear in the following format: “ERROR _X_Y”. X represents the category of the error. Y represents the specific issue. In the position of the X placeholder, the following numbers can appear to represent the category of the malfunction: Code Explanation...
7. ABOUT HEART RATE DETECTION Heart rate detection functions are selected at the time of purchase. Not every product includes every type of heart rate detection device. The following explains factors that influence the performance of two of the most common types of heart rate detection devices.
Note that in dry areas in particular, static electricity can interfere with unit operation and shock people. To discharge static electricity from your body, touch something else before touching metal on the product. 8. GUIDELINES fOR EXERCISE HOW HARD SHOULD I EXERCISE? Studies show that to benefit from aerobic exercise, people need to maintain a certain heart rate during their workouts.
9. ACCESSORIES There are accessories attached to this console; some are standard and some are optional. The following explains the details of each accessory and its function. USB CHARGER (Standard) The USB charger will provide 5V 500mA voltage for the smart phone or other devices charging.
9. ACCESSORIES (CONTINUED) Entertainment Cap (a) RFID member card slot: work with both optional SA WELL+ and ECOFIT member cards. (Not available yet.) (b) Bluetooth/WIFI connection button: press this button to pair the smart phone SA WELL+ App. (c) USB port: this port is used for device charging as well as optional data transferring.
9. ACCESSORIES (CONTINUED) MyE Wireless TV Audio_Channel Receivers: If your equipment has been installed MYE Wireless TV Audio_Channel Receivers, the display must has Channel Keys. Please make sure your equipment is with the correct sticker as below. (a) None Treadmill (Bike, Elliptical and Stepper...etc.) Left display: Without Channel Keys.
Page 53
9. ACCESSORIES (CONTINUED) MyE Wireless TV Audio_Channel Receivers fuctions: 1. The receiver has two kinds of module as below. (Note: MyE Wireless TV Audio_Channel Receivers and Module not provided.) (1). MC3R-9(900MHZ) must work with MYE Wireless TV Audio_Channel Receivers MWTD-S9. (2).
10. MAINTENANCE This section covers maintenance topics, including instructions on replacing a fuse and lubricating the walk belt, along with the presentation of a main- tenance schedule, maintenance task list, one-year maintenance log, and electronics block diagram. MAINTENANCE How to Replace a fuse If electrical current becomes too high, the fuse breaks.
MAINTENANCE Lubrication System Lubrication System flowchart Model No. Display ex: T655 Total Exercise 5 seconds Distance Display (km) Power On RESET Walks Belt Version Display Total Exercise Total Exercise Total Exercise Speed Total ex:T655 Distance Display (mile) Distance Display (km) Distance Display (km) Running Time...
Page 56
MAINTENANCE Lubrication System (Continued) To replace the lubricant bottle, follow instructions (a) through (d) below. (a) Loosen the screws on the bezel and push the bezel up. (b) Take the old lubricant bottle out. (c) Unscrew the nozzle from the old lubricant bottle and screw it onto new bottle.
Page 57
MAINTENANCE Lubrication System (Continued) Error Messages: There are 2 error messages with this system. Error 1: It indicates that the system memory failing and it will not be able to perform any auto lubrication. Error 2: It indicates motor is failing or system will not be able to perform any function.
MAINTENANCE Schedule Area Day Week Month Quarter Year Notes Exterior Clean. Screws Inspect and secure loose parts. Ensure the treadmill operates properly. Treadmill test Inspect alignment (centering) and look Walk belt for wear. Walk deck Inspect for wear. Belt guides Inspect for normal rotation.
MAINTENANCE Task List Like cars, fitness products require maintenance. Regular maintenance ex- tends product life, and failure to maintain products can void the manufac- turer’s warranty. Copy the maintenance log sheet, and record maintenance work for each fitness product. Daily tasks 1.