Advertisement
Operation Guide 5198
To confi gure Home City settings
Note
This watch does not have a city code that
corresponds to Newfoundland.
1.
Pull out the crown to the fi rst click.
The x Second Hand will move to the currently
selected Home City.
Leaving the crown pulled out for more than
two minutes without performing any operation
will automatically cause the setting operation
Home City
to become disabled. If this happens, press
the crown back in and then pull it out again to
confi gure settings.
E-40
Important!
If the area where you are located is under daylight saving time and you select
AUTO as the watch's standard time/daylight saving time setting, the time shown
by the watch will be one hour behind the actual time until a time calibration signal
operation is performed successfully. If you are in an area where signal reception
is not possible for some reason, change the above setting to DST (daylight saving
time).
Note
You can select one of 24 cities around the globe as your Home City. Whenever you
change your Home City, the time setting will change automatically to the current
time in that city.
Example: Changing your Home City from Tokyo to New York (standard time)
Home City
Before change
Tokyo (TYO/TOKYO) 10:00 a.m.
After change
New York (NYC/NEW YORK) 8:08 p.m. (standard time)
E-42
In an area where a time calibration signal cannot be received, you can switch
between STD and DST manually.
Note that you cannot switch between STD (standard time) and DST (daylight
saving time) while UTC* is selected as your Home City.
*
Coordinated Universal Time, the world-wide scientifi c standard of timekeeping. The
reference point for UTC is Greenwich, England.
If you experience problems receiving the time calibration signal in your area,
it probably is best to switch between standard time and daylight saving time
manually (page E-45).
Selecting this setting when your current Home City supports
time calibration signal reception will enable automatic
AUTO
switching between standard time and daylight saving time
based on signal data.
STD (standard time)
Switches to standard time.
DST (daylight saving time)
Switches to daylight saving time.
E-44
Confi guring Current Time Settings Manually
You can confi gure current time settings manually when the watch is unable to receive
a time calibration signal.
To change the current time setting manually
1.
E-46
Adjusting the Home Positions
Strong magnetism or impact can cause the hands or v Home City Indicator of the
watch to be off, even if the watch is able to perform the calibration signal receive
operation.
The watch automatically detects and adjusts the position of the x Second Hand as
required.
Note, however, that the watch does not automatically correct the positions of the
z Hour Hand, c Minute Hand, or v Home City Indicator. You need to correct the
positions of these manually.
E-48
Pull out the crown to the second click.
The x Second Hand will move to A
(AM) or P (PM) in accordance with the
current time.
2.
Rotate the crown to move the
city that you want to use as your Home City.
3.
Next, press
AUTO, STD (standard time), or DST (daylight saving
time), which indicates the current standard time/
daylight saving time setting. See "Standard Time and
Daylight Saving Time Settings" (page E-43).
4.
Push the crown back in.
The v Home City Indicator will show the city code
of the Home City you selected in step 2, above.
For about one second, the x Second Hand will
perform movement that indicates the current
charge level of the battery. It can take up to about
10 minutes before the watch returns to regular
timekeeping. See "Charging Guide" (page E-19).
Standard Time and Daylight Saving Time Settings
Daylight Saving Time (DST)
Daylight saving time (summer time) advances the time setting by one hour from
standard time. Remember that not all countries or even local areas use daylight
saving time.
The time calibration signals transmitted from Mainfl ingen (Germany), Anthorn
(England), or Fort Collins (the United States) include both standard time and daylight
saving time data.
Note that an AUTO setting will be indicated only if the currently selected city code
is one that supports calibration time signal reception. While AUTO is selected, the
watch will switch between STD and DST automatically in accordance with time
calibration signal data.
The initial default setting is AUTO when any one of the following city codes is
selected as the Home City code: LONDON (LON), PARIS (PAR), ATHENS (ATH),
NEW YORK (NYC), CHICAGO (CHI), DENVER (DEN), LOS ANGELES (LAX),
ANCHORAGE (ANC), or TOKYO (TYO).
To change the standard time/daylight saving time setting
1.
Pull out the crown to the fi rst click.
2.
Press
The x Second Hand will move to AUTO,
STD (standard time), or DST (daylight saving
time), which indicates the current standard
time/daylight saving time setting.
3.
Rotate the crown to move the
Hand to AUTO, STD (standard time), or DST
(daylight saving time) in accordance with the
setting you want.
4.
Push the crown back in.
Each press of A will toggle between the two settings shown below.
A
Time (hour, minutes)
2.
While the time setting is selected, rotate the crown to change the current time
setting.
Note
A high-speed movement feature (one hour maximum) is available when setting
the time. See "Crown Operations" (page E-6) for more information.
3.
After the time setting is the way you want, press
setting.
The x Second Hand will move to A (AM) or P (PM).
x Second Hand to the AM/PM setting you want.
4.
Rotate the crown to move the
5.
At the top of a minute (based on the time signal on the radio, TV, etc.), push the
crown back in to restart timekeeping.
The x Second Hand will restart timekeeping from 0 seconds (12 o'clock).
Adjusting Home Positions Manually
Important!
You do not need to perform the procedure in this section if the watch is indicating
the hour, minute, and Home City normally.
1.
Pull the crown out to the fi rst click.
2.
Hold down
x Second Hand moves to 12 o'clock.
The c Minute Hand and x Second Hand should
move to their correct home positions (12 o'clock)
when you release A. If they do, advance to step 5.
3.
What you should do next depends on how much the
hand positions are off, as described below.
Off within ±15 minutes 00 seconds: Perform steps 4,
5, and 6 of this procedure.
Off by more than ±15 minutes 00 seconds: Perform
steps 7, 8, 9, and 10 of this procedure.
x Second Hand to the
A. The x Second Hand will move to
E-41
E-43
A.
x Second
E-45
AM/PM
A to change to the AM/PM
E-47
A for at least fi ve seconds until the
E-49
Advertisement
