Setting Of Numeric Parameter (Numeric Param.); Numerical Parameter Composition - Canon Super G3 2nd Line FAX Board-AM1 Service Manual

5
Service Mode Service Mode > Setting of Numeric Parameter (NUMERIC Param.) > Numerical Parameter Composition

Setting of Numeric Parameter (NUMERIC Param.)

Numerical Parameter Composition

Sssw Menu Num Ncu Type
<1/10>
001 xxxxx
002 xxxxx
003 xxxxx
004 xxxxx
005 xxxxx
006 xxxxx
007
xxxxx
008
xxxxx
No. Function
002 RTN transmission condition (1)
003 RTN transmission condition (2)
004 RTN transmission condition (3)
005 NCC pause time (before ID code)
006 NCC pause time (after ID code)
007 pre-pause time at time of placing call
009 number of characters in telephone numbers
between transmitting and receiving parties
010 line connection identification time
011 T.30 T1 timer (for reception)
013 T30. EOL timer
027 preamble detection time for V21 low-speed flag
5 Service Mode > Setting of Numeric Parameter (NUMERIC Param.) > Numerical Parameter Composition Service Mode
ISDN Print Clear Test Report
<READY>
←（yyyyy）{aaaaa～bbbbb}
←（yyyyy）{aaaaa～bbbbb}
←（yyyyy）{aaaaa～bbbbb}
←（yyyyy）{aaaaa～bbbbb}
←（yyyyy）{aaaaa～bbbbb}
←（yyyyy）{aaaaa～bbbbb}
←（yyyyy）{aaaaa～bbbbb}
←（yyyyy）{aaaaa～bbbbb}
OK
F-5-12
Range of settings Initial setting
1% to 99% 10
2 to 99 times 15
1 to 99 lines 12
1 to 60 sec 4
1 to 60 sec 4
0 to 9999 (x10 ms) 0
0 to 20 characters 0
0 to 9999 (x10 ms) 5500
0 to 9999 (x10 ms) 3500
500 to 3000 (x10 ms) 1300
20 (x 10 ms) 0
<002: RTN transmission condition (1)><003: RTN transmission condition (2)><004: RTN
transmission condition (3)>
Use it to set RTN signal transmission conditions. Raise these parameters for more lenient
conditions if errors occur frequently at time of reception because of transmission of the RTN
signal.
Error Code:
Any of the following error codes may be indicated at time of reception because of RTN signal
transmission
##104, ##107, ##114, ##201
MEMO:
RTN signal transmission condition (1) affects the ratio of error lines to the total number
of lines per single page of received images.
RTN signal transmission condition (2) affects the standard value (*2) of burst errors (*1).
RTN signal condition (3) affects the number of errors not reaching the standard value of
burst errors.
*1: transmission error occurring cover several lines.
*2: for instance, if '15' is set, a single burst error will represent an error occurring
continuously cover 15 lines.
If any of these lines is detected while an image signal is being received, the RTN signal
will be transmitted after receiving the protocol signal of the transmitting party. Higher
parameters restrict the transmission of the RTN signal.
<005: NCC pause length (pre-ID code)>
Use it to set the length of the pause automatically entered between access code and ID code
when the NCC (New Common Carrier) line is used for dialing.
<006: NCC pause length (post-ID code)>
Use it to set the length of the pause automatically entered between ID code and telephone
number of the other party when the NCC (New Common Carrier) line is used for dialing.
T-5-19
<007: pre-pause length at time of ring>
Use it to set the length of the pause used when placing a call.
<009: number of comparison digits of source telephone number and target telephone
number>
Use it to set the number of TSI comparison characters (lower $ characters) for a check on
telephone numbers.
5-15
5-15