U-Line H-6501 Manual

U-Line H-6501 Manual

High-viscosity electric drum pump
Table of Contents
  • Seguridad General
  • Conexión a Tierra
  • Instalación y Operación
  • Mantenimiento
  • Solución de Problemas
  • Sécurité Générale
  • Mise à la Terre
  • Installation et Fonctionnement
  • Dépannage

Advertisement

Available languages

Available languages

Quick Links

π
H-6501
HIGH-VISCOSITY
ELECTRIC DRUM PUMP
GENERAL SAFETY
This pump is designed to transfer clean, non-abrasive,
and nonflammable liquids that are compatible with
pump materials.
For a list of materials and compatible chemicals, see
uline.com.
Other factors such as viscosity, pressure, specific
gravity, temperature, concentration and chemical
combinations should also be considered when
determining compatibility. Always contact your
chemical supplier for compatibility recommendations.
Final selection should be based on actual field testing
under the conditions of intended use.
1.
Know the pump application, limitations and
potential hazards.
CAUTION! Do not use to pump flammable
or explosive fluids, such as gasoline, fuel
oil, kerosene, etc. Do not use in explosive
atmospheres. Pump should only be used with
liquids compatible with pump component
materials. Failure to follow this warning can
result in personal injury and/or property
damage.
2. Make certain that the power source conforms to the
requirements of the equipment.
3. Provide adequate protection and guarding around
moving parts.
4. Disconnect power before servicing.
PAGE 1 OF 9
1-800-295-5510
uline.com
SAFETY
5. Release all pressure within pump before servicing
any component.
6. Drain all liquids from pump before servicing.
7.
Secure the discharge line before starting the pump.
An unsecured discharge line will whip, possibly
causing personal injury and/or property damage.
8. Before each use, check hoses for weak or worn
condition, making certain that all connections are
secure.
9. Periodically inspect pump components. Perform
routine maintenance as required.
(See Maintenance section)
10. Provide a means of pressure relief for pumps where
discharge line can be shut off or obstructed.
11. Personal Safety –
a. Wear safety glasses at all times when working
with pump.
b. Wear a face shield and proper apparel when
pumping hazardous chemicals.
12. When wiring an electrically-driven pump, follow all
electrical and safety codes, as well as the most
recent United States National Electrical Code (NEC)
and the Occupational Safety and Health Act (OSHA).
Para Español, vea páginas 4-6.
Pour le français, consulter les pages 7-9.
CAUTION! Risk of electrical shock! Never
connect the green (or green and yellow) wire to
a live terminal!
0721 IH-6501

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the H-6501 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for U-Line H-6501

  • Page 1 Para Español, vea páginas 4-6. Pour le français, consulter les pages 7-9. π H-6501 1-800-295-5510 uline.com HIGH-VISCOSITY ELECTRIC DRUM PUMP SAFETY GENERAL SAFETY 5. Release all pressure within pump before servicing any component. This pump is designed to transfer clean, non-abrasive, 6.
  • Page 2: Grounding Methods

    SAFETY CONTINUED GROUNDING To ensure a proper ground, the grounding means must be tested by a qualified electrician. To reduce the risk of electrical shock, the motor must Use only 3-wire extension cords that have 3-prong, be securely and adequately grounded. This can be grounding type plugs and 3-pole receptacles that accomplished by either: accept the equipment plug.
  • Page 3: Maintenance

    MAINTENANCE CAUTION! Disconnect power before servicing. 4. Pump should be checked daily, weekly and monthly for proper operation. If anything has changed since Do not stand the pump on its shaft. unit was new, unit should be removed and repaired 1.
  • Page 4: Seguridad General

    π H-6501 800-295-5510 uline.mx BOMBA ELÉCTRICA PARA ALTA VISCOSIDAD PARA TAMBOS SEGURIDAD SEGURIDAD GENERAL 5. Libere toda presión en la bomba antes de darle mantenimiento a cualquier componente. Esta bomba está diseñada para transferir líquidos limpios 6. Drene todo el líquido de la bomba antes de darle no abrasivos y no inflamables que sean compatibles mantenimiento.
  • Page 5: Conexión A Tierra

    CONTINUACIÓN DE SEGURIDAD CONEXIÓN A TIERRA Para asegurar una conexión adecuada a tierra, los medios de conexión a tierra deberán de ser probados Para reducir el riesgo de descarga eléctrica, el motor por un electricista calificado. deberá estar conectado a tierra de forma segura. Esto Utilice solamente extensiones de 3 alambres que se puede lograr de la siguiente manera: tengan una clavija de 3 picos a tierra y enchufes de 3...
  • Page 6: Mantenimiento

    CONTINUACIÓN DE INSTALACIÓN Y OPERACIÓN La unidad no es resistente al agua y no está Para instalaciones en exteriores, el motor deberá fabricada para usarse en regaderas, saunas y otras protegerse con una cubierta que no bloquee ubicaciones potencialmente húmedas. El motor el flujo de aire hacia y alrededor del motor.
  • Page 7: Sécurité Générale

    π H-6501 1-800-295-5510 uline.ca POMPE À BARIL ÉLECTRIQUE – HAUTE VISCOSITÉ SÉCURITÉ SÉCURITÉ GÉNÉRALE 5. Avant l'entretien de tout composant, évacuez toute la pression à l'intérieur de la pompe. Cette pompe est conçue pour transvider des liquides 6. Avant l'entretien de l'appareil, videz tout liquide propres, non abrasifs et ininflammables qui sont restant dans la pompe.
  • Page 8: Mise À La Terre

    SÉCURITÉ SUITE MISE À LA TERRE Pour assurer un bon raccordement de mise à la terre, les moyens de mise à la terre doivent être vérifiés par un Tour réduire le risque de choc électrique, le moteur doit électricien qualifié. être correctement mis à...
  • Page 9: Dépannage

    INSTALLATION ET FONCTIONNEMENT SUITE REMARQUE : La pompe se videra une fois température ambiante près du moteur ne doit pas dépasser 40 °C (104 °F). Si installé à l'extérieur, le débranchée. moteur doit être protégé par un écran qui ne bloque Cet appareil n'est pas étanche et ne doit pas être pas le débit d'air autour du moteur.

Table of Contents