Advertisement
Binks "STEADI-GRIP"
2 QT. PRESSURE CUPS
MAX. WORKING PRESSURE . . . . . . . . . . . . . . . . . . . . 50 psig
OVERALL HEIGHT
WITH AUXILIARY HANDLE . . . . . . . . . . . . . . . . . 16 15/16 in
WITHOUT AUXILIARY HANDLE . . . . . . . . . . . . . 13in
BASE DIAMETER . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . 5 1/4in.
AIR INLET & OUTLET CONNECTION SIZE . .. . . . . . . . 1/4 NPS (m)
FLUID OUTLET CONNECTION SIZE . . . . . . .. . . . . . . . 3/8 NPS (m)
FLUID CAPACITY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Qts (US)
WEIGHT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 lb.3oz.
Model No. 80-295-CE
SPECIFICATIONS
1
SB-E-4-231
ISS.01
© 2004 ITW Finishing Systems and Products
3.5 bar
430 mm
330 mm
133 mm
-
-
1.9 Ltr
1.46 kg
Advertisement
Table of Contents
Related Manuals for Binks 80-295-CE
Summary of Contents for Binks 80-295-CE
- Page 1 SB-E-4-231 ISS.01 Binks “STEADI-GRIP” 2 QT. PRESSURE CUPS Model No. 80-295-CE SPECIFICATIONS MAX. WORKING PRESSURE ....50 psig 3.5 bar OVERALL HEIGHT WITH AUXILIARY HANDLE .
- Page 2 WARNING The following hazards may occur during the normal use of this equipment. Please read the following chart. HAZARD CAUSE SAFEGUARDS FIRE 1. Adequate exhaust must be provided Solvents and coatings can be to keep the air free of highly combustible, especially accumulations of flammable when sprayed.
- Page 3 INTRODUCTION Binks “Steadi-Grip” Pressure Cups are CE marked in accordance with the ATEX Directive 94/9/EC, Cat 2 G X for use in Zones 1 and 2. These Cups are ideal for component spraying and industrial applications where small batch production spraying is required. The 2 qt. capacity is sufficient to complete large spray jobs without refilling the cup.
- Page 4 PARTS LIST ITEM PART DESCRIPTION 20-353-1 HEX JAM NUT 5/16" † 72-1022 CENTER POST ASSEMBLY 1 80-4 (2 Quart) COVER GASKET (Tri Seal ○ 80-11-5 Foam) 80-12 RELIEF VALVE STEM 80-267 CHECK VALVE ○ 60-7 CHECK VALVE SPRING 80-33 FLUID OUTLET 80-34 FLUID TUBE (2 Quart)
- Page 5 MODEL 80-295 PRESSURE CUP © 2004 ITW Finishing Systems and Products...
- Page 6 SETUP AND OPERATION Refer to “TYPICAL INSTALLATION” drawing fluid pressure adjustment knob on cup handle. below Set up the “Steadi-Grip” with the CONVENTIONAL or CLEANING HVLP gun along with at least 5 ft. of air and fluid 1. Open air release valve on pressure cup cover. hose.
- Page 7 As the manufacturers representative of the items listed below: TYPE : SG Pressure Feed Cup MODEL: 80-295-CE Declare, under our sole responsibility, that the equipment to which this document relates is in conformity with the following standards or other normative documents:...
- Page 8 ITW Finishing Systems and Products Ringwood Road, Bournemouth, BH11 9LH, England. Tel. No. (01202) 571111 Telefax No. (01202) 581940, Website address http://www.itweuropeanfinishing.com ITW Oberflächentechnik GmbH & Co. KG Justus-von-Liebig-Straße 31 63128 Dietzenbach Tel (060 74) 403-1 Telefax: (060 74) 403300 Website address http://www.itw-finishing.de ITW Surfaces Et Finitions 163-171 avenue des Auréats B.P.
Need help?
Do you have a question about the 80-295-CE and is the answer not in the manual?
Questions and answers