Table of Contents
Advertisement
CONTROLS
12
) ) ) ) ) REPEAT
–
to repeat a track, a disc, or all
available discs.
¡ ¡ ¡ ¡ ¡ MUTE
–
to switch off the sound temporarily.
™ ™ ™ ™ ™ SHUFFLE
–
to play all the available discs and
their tracks in random order.
£ £ £ £ £ SLEEP
–
to switch the system to standby
mode at a selected time.
≤ ≤ ≤ ≤ ≤
–
to switch the system to standby
mode.
Notes for remote control:
– First select the source you wish
to control by pressing one of the
source select keys on the remote
control (e.g. CD or TUNER).
– Then select the desired function
(É, í, ë, etc.).
13
To reinstall the PLUG & PLAY
1 In Standby or Demostration mode,
press and hold PLAY (on the system
only) "AUTO INSTALL - PRESS
PLAY" will be displayed.
2 Press PLAY (on the system only)
again to start installation.
• To exit without storing the PLUG
and PLAY, press Ç button (on the
system only).
Notes:
– PLUG and PLAY will be reinitiated
again during the next power up if :
i) PLUG and PLAY installation was not
completed.
ii) No stereo frequency being detected
during PLUG and PLAY, "CHECK
ANTENNA" will be displayed.
– You can store any radio stations
manually or automatically after PLUG
and PLAY.
– When PLUG and PLAY is used, all
previously stored radio stations will be
replaced.
– During PLUG and PLAY, if no button is
pressed within 15 seconds, the system
will go to demonstration mode (if
demonstration mode is enable)
2-4
OPERATING THE SYSTEM
Demonstration mode
The system has a demonstration mode
that shows the various features offered
by the system.
To disable the demonstration
mode
• Press and hold Ç (on the system
only) for five seconds when the
system is in demonstration mode.
™ "DEMO OFF" is displayed.
™ The system will switch to standby
mode.
To enable the demonstration
mode
• Press and hold Ç (on the system
only) for five seconds when the
system is in standby mode.
™ The demonstration will begin.
Notes:
– If the demonstration mode has not been
disabled, it will resume five seconds later
after the system switches to standby
mode.
– When the system is switched on from
the main power outlet, the CD changer
tray may open and close again to
initialize the set.
– Even though the AC power cord is
removed from and reconnected to the
wall socket, the demonstration will
remain off until it is switched on again.
OPERATING THE SYSTEM
MINI HIFI SYSTEM
STANDBY-ON
CD1 • 2 • 3
FM•AM
CD
TUNER
TUNING
DEMO STOP
SEARCH
STOP• CLEAR
DSC
•
PROGRAM
CLOCK
TIMER
DIGITAL SOUND CONTROL
Important:
Before you operate the system,
complete the preparation
procedures.
Plug and Play
The system provides PLUG and PLAY
feature that allows you to store all
available radio stations automatically
upon power up.
If the PLUG and PLAY has not
been installed
1 Upon power up, "AUTO INSTALL -
PRESS PLAY" will be displayed.
Switching the system ON
• Press CD, TUNER, TAPE or AUX.
• Press STANDBY-ON in demo.
You can also switch on the system by
pressing any one of the CD DIRECT
PLAY buttons (on the system only).
Switching the system to
standby mode
• Press STANDBY-ON or
on the
remote control.
™ The system will switch to standby
mode.
Selecting the Source
• Press the respective source selection
button: CD, TUNER, TAPE or
AUX.
™ The display indicates the selected
source.
Note:
– For an external source, make sure you
have connected the audio left and right
OUT terminals of the external
equipment (TV, VCR, Laser Disc player,
DVD player or CD Recorder) to the
AUX IN terminals.
TAPE 1 • 2
VIDEO
MASTER
VOLUME
TAPE
AUX
▲
PRESET
PLAY• PAUSE PREV
NEXT
DYNAMIC BASS BOOST
2 Press PLAY (on the system only) to
start installation.
™ "INSTALL" will be displayed and
followed by "TUNER" and then
"AUTO".
™ The
starts flashing.
PROGRAM
™ PLUG and PLAY will start
searching for all radio stations on
FM band and then followed by
radio stations on AM band.
™ All available radio stations with
sufficient signal strength will be
stored. Up to 40 presets may be
stored.
™ The last preset radio station will
appear on the display when PLUG
and PLAY is completed.
DIM mode
(only on remote control)
You can select the desired brightness
for the display.
• Press DIM to select DIM 1, DIM 2,
DIM 3 or DIM OFF display mode.
™ The
display lights up.
DIM
™ "DIM 1", "DIM 2", "DIM 3" or
"DIM OFF" will be displayed
depending on the mode selected.
DIM OFF - normal brightness with
Volume Indicator On
DIM 1 - normal brightness with
Volume Indicator Off
DIM 2 - half brightness with Volume
Indicator On
Advertisement
Table of Contents
