Advertisement
Quick Links
GB - ENGLISH
Operating Instructions
Dear Customer,
Many thanks for the confidence you have shown in us with the purchase of your new PROMAC-machine. This manual has been
prepared for the owner and operators of a JD-3285-M or JD-3285-T drill press to promote safety during installation, operation
and maintenance procedures. Please read and understand the information contained in these operating instructions and the
accompanying documents. To obtain maximum life and efficiency from your machine, and to use the machine safely, read this
manual thoroughly and follow instructions carefully.
...Table of Contents
1. Declaration of conformity
2. Warranty
3. Safety
Authorized use
General safety notes
Table tilt adjustment
1. Declaration of conformity
On our own responsibility we hereby
declare that this product complies with
the regulations* listed on page 2.
Designed in consideration with the
standards**.
2. Warranty
TOOL FRANCE SARL guarantees that
the supplied product(s) is/are free from
material defects and manufacturing
faults.
This warranty does not cover any
defects which are caused, either
directly or indirectly, by incorrect use,
carelessness, damage due to
accidents, repairs or inadequate
maintenance or cleaning as well as
normal wear
and tear.
Further details on warranty (e.g.
warranty period) can be found in the
General Terms and Conditions (GTC)
that
are an integral part of the contract.
These GTC may be viewed on the
website of your dealer or sent to you
upon request.
TOOL FRANCE SARL reserves the
right to make changes to the product
and accessories at any time.
3. Safety
3.1 Authorized use
This drill press is designed for drilling
wood and machinable metal and
plastic materials only. Machining of
other materials is not permitted and
may be carried out in specific cases
only after consulting with the
manufacturer.
Never cut magnesium-
high danger of fire!
The workpiece must allow to safely be
loaded and clamped for machining.
The proper use also includes
compliance with the operating and
maintenance instructions given in this
manual.
3
The machine must be operated only by
persons familiar with its operation and
maintenance and who are familiar with
its hazards.
The required minimum age must be
observed.
The machine must only be used in a
technically perfect condition.
When working on the machine, all
safety mechanisms and covers must
be mounted.
In addition to the safety requirements
contained in these operating
instructions and your country's
applicable regulations, you should
observe the generally recognized
technical rules concerning the
operation of wood- and metal-working
machines.
Any other use exceeds authorization.
In the event of unauthorized use of the
machine, the manufacturer renounces
all liability and the responsibility is
transferred exclusively to the operator.
3.2 General safety notes
Drill press can be dangerous if not
used properly. Therefore the
appropriate general technical rules as
well as the following notes must be
observed.
Read and understand the entire
instruction manual before attempting
assembly or operation.
Keep this operating instruction close
by the machine, protected from dirt
and humidity, and pass it over to the
new owner if you part with the tool.
Advertisement
Related Manuals for Promac JD-3285-M
Summary of Contents for Promac JD-3285-M
-
Page 1: Table Of Contents
Dear Customer, Many thanks for the confidence you have shown in us with the purchase of your new PROMAC-machine. This manual has been prepared for the owner and operators of a JD-3285-M or JD-3285-T drill press to promote safety during installation, operation and maintenance procedures. -
Page 2: Remaining Hazards
No changes to the machine may be Do not operate the machine under the Make all machine adjustments or made. influence of drugs, alcohol or any maintenance with the machine medication. Be aware that medication unplugged from the power source. Daily inspect the function and can change your behaviour. -
Page 3: Machine Specifications
Range of speeds 180 - 3000 rpm 5. Transport and start up Net weight 61 kg 5.1 Transport and installation JD-3285-M: The machine is designed to operate in Mains 230V ~1/N/PE 50Hz closed rooms and must be placed Output power 0.75 kW (1 HP) S1... -
Page 4: Mains Connection
Install three down feed handles (A, The mains voltage must comply with Fig. 5) into the down feed hub (B). the information on the machine licence plate. The mains connection must have a 10 A surge-proof fuse. Only use power cords marked H07RN- Connections and repairs to the electrical equipment may only be carried out by qualified electricians. -
Page 5: Setup And Adjustments
Generally speaking, the smaller in relation the drill bit, the greater the RPM required. Wood requires higher speeds than metal. Metal is usually drilled at slower speeds; cutting oil is applied if necessary. Warning: Always keep your hands well clear of the rotating bit. -
Page 6: Return Spring Adjustment
7.6 Cross Laser Adjustment 7.7 LED Work Light Adjustment The lasers are designed for use with The integrated LED work light is twist drill bits. adjustable. There will be shadowing with wider Push on the rim of the light to adjust tools, such as Forstner bits, therefore (B, Fig 16). -
Page 7: Environmental Protection
Please leave it at a specialized institution. This symbol indicates separate collection for electrical and electronic equipment required under the WEEE Directive (Directive 2012/19/EC) and is effective only within the European Union. 11. Available accessories Refer to the PROMAC-Pricelist.