Ryobi AJP-1100 Owner's Operating Manual page 4

Carefully read and understand these instructions
before operating this high pressure washer.
Package Contents (Fig.1)
1. Main unit
2. Handle
. Spray handle holder
4. Cord hook
5. Wheel
6. Wheel cover
7. Variable nozzle lance
8. Mid nozzle lance
9. Spray handle
10. Spray handle hose (5m)
11. Detergent bottle
12. Water connector
1. Hose joint
14. Nozzle cleaning pin
15. Screw
Technical data
Power rating input
Rated pressure
Allowable pressure
Rated flow
Max. inlet water pressure
Max. temperature:
Adding water
Weight
Sound pressure level
Uncertainty
Sound power level
Vibration Value
Name of Parts:
1. Main unit
2. Handle
. Spray handle holder
4. Cord hook
5. Wheel
6. Wheel cover
7. Variable nozzle lance
8. Mid nozzle lance
9. Spray handle
10. Spray handle hose
11. Detergent bottle
12. Water connector
1. Hose joint
14. Nozzle cleaning pin
15. Screw
16. Water supply hose (option)
1,400 W
70 bar (7 MPa)
100 bar (10 MPa)
5.5 L / min
0.7 MPa
40℃
From a faucet
4.5 Kg
LpA=77dB(A)
KPA=dB
LwA=92dB(A)
aH=1.8m/s
2
Kah=0.05m/s
2
17. Hose clamp (option)
18. Main switch
19. Safety lock button
20. Trigger
21. Power cord
22. Filter
2. Hook
24. Hook
25. Water inlet
26. Release button
27. Release button
Preparation
Before starting up your machine, we advise you to carefully
read through this instruction manual. Follow all instructions
to minimize the risk of injuries when using the machine.
Prior to operation
Before starting up your machine, please check it carefully for
any defects. If you find any, do not start up your machine and
contact your distributor.
Especially check:
The insulation of the electric cable should be faultless and
without any cracks. If the electric cable is damaged, it should
be replaced by RYOBI authorized distributor.
Mains power supply connection
The following should be observed when connecting the
machine to the electric installation:
• Check before operation that the local power supply is the
same as the specifications on the rating label.
• This machine is equipped with universal motor with double
insulation. It is not necessary to have earth connection.
• The electric installation shall be made by a certified
electrician.
• It is strongly recommended that the power supply to the
machine should include a residual current device (RCD).
• Product protection degree:IPX5
General safety regulations and accident
prevention
It is essential that you read the safety regulations and
operating instructions in their entirety and follow the
information contained therein in order to eliminate the
possibility of an accident or potentially dangerous situation
from occurring while working with the machine.
• The power plug must be plugged into a properly installed
socket. The power supply should include a residual
current device for max. 0 mA.
• Always check the device, the mains cable and the plug
before using the machine. Only operate the device when
it is in good working order and has not been damaged in
any way. Damaged parts must be immediately replaced
by a qualified electrician.
• Always pull the power plug out of the socket outlet before
doing any work on the machine, before changing the
nozzle and whenever it is not being used.
• Warning! Inadequate extension cords can be dangerous.
• If an extension cord is used, it shall be suitable for outdoor
use, and the connection has to be kept dry.
• Only use suitable extension cable when working outdoors.
Extension cable must have a minimum cross-section of
1.5 mm 2 .
• Warning! This device was developed to be used with
cleaning agents supplied or recommended by the
manufacturer. The use of any other cleaning agents or
chemicals can negatively affect the safety of the device.
• Cable connections should be kept dry and off the ground.
Always uncoil the extension cable completely to avoid
heat damage to the cable.
• Warning! Do not use the device when other persons or
animals are in the near vicinity unless they are wearing
appropriate protective clothing.