Subscribe to Our Youtube Channel
Related Manuals for INDIWORK IW04A-N
Summary of Contents for INDIWORK IW04A-N
- Page 1 Release Date: 2018 - 10 - 22 Instruction Manual High-Definition Link for Audi IW04A-N Model Name IW04A-N Latest Firmware Date 2017 - 02 - 02 Manual Version Rev. 3.8 Language English...
-
Page 2: Table Of Contents
Contents • Cautions _____________________________________________________________ 3 • Dimension & Exterior _________________________________________________ 4 • Components & Optional parts _________________________________________ 5 • Full Installation Diagram ______________________________________________ 6 • CAN wires information(exceptions) ____________________________________ 7 • HDMI Connection Diagram ____________________________________________ 9 • Navigation Connection Diagram ______________________________________ 10 •... -
Page 3: Cautions
Navigation(GPS) box_related • When you connect the power wires(B+, ACC) to the navigation(GPS) box, the ‘NAVI 12V OUT' wire supported by IW04A-N should be spliced with an ACC wire of navigation box. • After installation is done, select an applicable navigation(GPS) box model in the 'Navigation model selection menu' of setting mode. -
Page 4: Dimension & Exterior
Dimension Width: 142 mm Height: 22 mm Length: 91 mm ⓐ ⓑ ⓒ ⓓ ⓔ Exterior ⓐ DIP SWITCH ⓑ AV IN / OUT ⓒ TOUCH IN (Not Used) ⓓ MODE ⓔ POWER / CAN ⓕ HDMI IN ⓖ 5V USB POWER ⓗ... -
Page 5: Components & Optional Parts
Power / CAN Cable LVDS Cable LVDS PCB HDMI Cable AV IN / OUT Cable 5-pin Micro USB Cable Optional Parts (sold separately at the indiwork) HDMI Cable HDMI Extender Mode Switch (Male to Male) (For stick type HDMI device) -
Page 6: Full Installation Diagram
※ Speciality Connector Type Full Installation Diagram MMI DATA Pin Specification GND Input B+ Power Input NAVI 12V Power Output ※ Optional External Devices Mode Switch GND Output (optional) RV-CAM Video Input Original Main-Harness External Rear View 12V Power Output &... -
Page 7: Can Wires Information(Exceptions)
CAN wires information(exceptions) < 2010, 2011 Audi A4 > < 2012~ Audi Q3 > Climate Controller – 20-Pin Connector Climate Controller – 16-pin Connector 19 20 12 13 POWER / CAN Cable POWER / CAN Cable HS CAN L HS CAN L Pin # 4 = HS CAN HIGH(Orange / Light Green) Pin # 12 = HS CAN LOW(Orange / Brown) HS CAN H... - Page 8 CAN wires information(exceptions) < 2015 Audi A1> Climate Controller – 20-Pin Connector POWER / CAN Cable HS CAN L Pin # 1 = HS CAN HIGH (Orange / Light Green) HS CAN H IR OUT Pin # 2 = HS CAN LOW(Orange / Brown) AUDI MMI LS CAN L LS CAN H...
-
Page 9: Hdmi Connection Diagram
HDMI Connection Diagram HDMI Device HDMI Device HDMI IN 5V USB NAVI IN UART I/F LVDS OUT HDMI IN 5V USB NAVI IN UART I/F LVDS OUT POWER POWER HDMI HDMI HDMI HDMI (5V-1A Power output for HDMI Device) (5V-1A Power output for HDMI Device) (Male) (Female) (HDMI Extender) -
Page 10: Navigation Connection Diagram
Navigation Connection Diagram Navigation Connection Diagram Navigation(GPS) Box Navigation(GPS) Box HDMI IN 5V USB NAVI IN UART I/F LVDS OUT HDMI IN 5V USB NAVI IN UART I/F LVDS OUT POWER POWER HDMI HDMI Touch screen panel Touch screen panel (USB cable connecting is for ‘N-Link’... -
Page 11: Compatibility Chart For Navigation(Gps) Box Models
(HDMI to HDMI) ↑ MYVI South Korea MS1400 Digital OFF(↓): 1, 2, 3 HDMI Cable ON(↑) : 4 (HDMI to HDMI) • The ‘IW04A-N(HD-Link)' supports navigation(GPS) box models equipped with 'Digital video output'. • It does not support the 'RGB video signals'. -
Page 12: Lvds Connection Diagram
LVDS Connection Diagram LVDS Connection HDMI IN 5V USB NAVI IN UART I/F LVDS OUT POWER MMI 3G Plus & 3G Head Unit HDMI • 'Genuine(OEM) LVDS connector' should be connected to 'LVDS IN / OUT PCB'. • ‘Provided LVDS connector' should be connected to the head unit instead to the genuine connector. -
Page 13: Hazard Module Connection Diagram
Hazard Module Connection Diagram A4, A5, Q3 / 6-Pin Hazard Connector POWER / CAN AV IN / OUT DIP SWITCH MODE TOUCH-IN Pin # 2 = Hazard(-) (Red/Yellow) Pin # 2 = Hazard(-) (Brown/Red) A6, A7 / 5-Pin Hazard Connector Old Version Module New Version Module Hazard... -
Page 14: Body Connector Specifications
Body Connector specifications MODE TOUCH-IN DIP SWITCH AV IN / OUT POWER / CAN Length: 20 cm Length: 100 cm Length: 150 cm BATTERY POWER INPUT RV-CAM VIDEO INPUT GND(RV-CAM VIDEO) GND INPUT RV-CAM POWER OUT GND OUTPUT(RV-CAM) GND OUTPUT REVERSE DETECTION IR OUT NAVI 12V POWER OUTPUT... -
Page 15: Car Compatibility Chart
Specific Models Year 2015 - 2010 - 2011 - 2010 - 2011 C6 (MMI 3G) IW04A-N is used in combination with Audi MMI(Multi Media Interface) 2011 - 2014 system. 2010 - 2014 - MMI navigation (3G) - MMI navigation plus (3G) -
Page 16: Activation By Original Buttons Of Audi
< OEM → AV2 > Press the button 4 times consecutively. If you visit car service center, you can System lock the all functions of IW04A-N. MMI 3G Plus Controller Locking / Press the button 10 seconds long. It is only possible to use the OEM Unlocking functions under it is locked. -
Page 17: Activation By Original Buttons Of Audi Q3 (6.5-Inch Screen Model)
Activation by original buttons of Audi Q3 6.5-inch screen model For Q3 6.5-inch screen model Button Function Operation Remarks Changing Press the ‘iNAV’ button short. Order: HDMI → NAVI → AV1 → AV2 → OEM Modes iNAV Back to Press the button short. Return to the OEM mode in any modes. -
Page 18: Dip Switch Settings
DIP Switch Settings No.6 No.7 No.8 No.9 No.10 Car Models CAN wires Information A6, A7, A8 / 2012~ OFF(▲) OFF(▲) OFF(▲) OFF(▲) OFF(▲) HS CAN = Climate controller (8-inch / 800*480) ON: ▼ OFF:▲ A4 / 2010 HS CAN = Climate controller OFF(▲) OFF(▲) ON(▼) -
Page 19: Settings
Settings For MMI 3G Plus & MMI 3G Button Function Operation Enter into the MENU(SETUP) Press the button 5 seconds long. setting menu Back to previous BACK(RETURN) Press the button short. menu Select the menu Selection Press the button short. and setting values. -
Page 20: Hdmi Mode Settings
Settings 2. HDMI mode settings - Mode selection: HDMI ↔ NAVI - Image display = Adjust the values of brightness and contrast Red-Green-Blue colors of HDMI display. - Screen position & size = Adjust position and size of HDMI display. 3. -
Page 21: Rear View Camera Settings
Settings 4. Rear view camera settings - Parking guide lines = Adjust position of parking guide lines and select the lines ‘ON or OFF’. - Parking distance control = Adjust position of parking distance control sensors to ‘LEFT or RIGHT’ and select the PDC ‘ON or OFF’. - Image display = Adjust the values of brightness and contrast Red-Green-Blue colors of Rear view camera display. -
Page 22: Automatic Activation Function(Av1)
Settings 6. Automatic activation function(AV1) - Shift gear from reverse to drive - Shift gear from parking to drive * When you shift gear ‘from reverse to drive’ or ‘from parking to drive’, it just works automatically during the activation time you selected. 7. -
Page 23: Keep The Rear Camera View
Settings (SURROUND VIEW OPTION) Keep the rear camera view - Shift gear from reverse to drive - Shift gear from parking to drive * When you shift gear ‘from reverse to drive’ or ‘from parking to drive’, it just works during the activation time you selected. -
Page 24: System Settings
- Factory default = Reset all setting values to factory default setting. 9. System information - Mode name: IW04A-N - Firmware date: 2016 - 04 - 15 (Latest firmware date) - = You can check the current firmware version date. -
Page 25: Information Of Dip Switch Settings
Settings 10. Information of Dip switch settings * You can check the current positions of dip switch settings. ex 1) ex 2) Actual DIP switch values. (→) Actual DIP switch values. (→) Appears on the setting menu. (↓) Appears on the setting menu. (↓) - Page 26 Copyright ⓒ indiwork. All Rights Reserved.
Need help?
Do you have a question about the IW04A-N and is the answer not in the manual?
Questions and answers