Page 1
Release Date: 2016 - 09 - 07 Instruction Manual High-Definition Link for BMW IW04B-N Model Name IW04B-N 2016 – 08 - 12 Latest Firmware Date Manual Version Rev. 2.3 Language English...
Navigation(GPS) box-related • When you connect the power wires(B+, ACC) to the navigation(GPS) box, the ‘NAVI (12V) OUT' wire supported by IW04B-N should be spliced with an ACC wire of navigation box. • After installation is done, select an applicable navigation(GPS) box model in the 'Navigation model selection menu' of setting mode.
Dimension Width: 97 mm Height: 21 mm Length: 142 mm ⓓ ⓐ ⓑ ⓒ Exterior ⓐ DIP SWITCH ⓑ AV IN / OUT ⓒ MODE ⓓ POWER / CAN ⓔ HDMI IN ⓕ 5V USB POWER ⓖ NAVI IN ⓗ UART I/F 5V USB HDMI IN POWER...
Components Power / CAN Cable LVDS Cable AV IN / OUT Cable 5-pin Micro USB Cable Optional Parts (sold separately at the indiwork) Mode Switch HDMI Extender (For stick type HDMI device)
Full Installation Diagram ※ CAN HIGH / LOW Pin Specification IR OUT ※ Optional External Devices NAVI 12V Power Output (ACC 12V OUT) GND Output(GROUND) Mode Switch (optional) RV-CAM Video Input External Rear View 12V Power Output & GND Output(RV-CAM Power) Camera Reverse Signal Detection(optional) Monitor Main-Harness...
HDMI Connection Diagram HDMI Device HDMI Device 5V USB 5V USB HDMI IN HDMI IN POWER POWER HDMI HDMI HDMI HDMI HDMI (5V-1A Power output for HDMI Device) (5V-1A Power output for HDMI Device) (Male) (Female) (HDMI Extender) (HDMI Cable) ‘Dongle &...
(HDMI to HDMI) ↑ MYVI South Korea MS1400 Digital OFF(↓): 1, 2, 3 HDMI Cable ON(↑) : 4 (HDMI to HDMI) • The 'IW04B-N(HD-Link)' supports navigation(GPS) box models equipped with 'Digital video output'. • It does not support the 'RGB video signals'.
UART I/F POWER Monitor(OEM) (Provided LVDS Cable) 'Genuine(OEM) LVDS connector' should be connected to IW04B-N LVDS IN / OUT port ‘Provided LVDS connector' should be connected to the monitor instead to the genuine connector. Cable (OEM LVDS Cable) Head Unit...
Hazard Module Connection POWER / CAN AV IN / OUT DIP SWITCH MODE TOUCH-IN Hazard button 6-pin Hazard connector Old Version Module New Version Module Hazard Hazard Module Module (4-Pin) (3-Pin) Pin # 5 = Hazard(-) (Brown/Blue) (For IW04-MB14) IR IN (20 cm) (100 cm) *Hazard Module is just available with ‘Smart Drive function of N-Link’...
Body Connector specifications POWER / CAN MODE AV IN / OUT DIP SWITCH ON 1 Length : 20 cm Length : 100 cm Length: 150 cm BATTERY POWER INPUT RV-CAM VIDEO INPUT GND(RV-CAM VIDEO) GND INPUT RV-CAM POWER OUT GND OUTPUT(RV-CAM) GND OUTPUT REVERSE DETECTION IR OUT...
2011 - 2013 X5 series 2009 -2013 X6 series 2010 - 2013 E71, E72 The IW04B-N supports the BMW original screen equipped with ‘4-pin LVDS round connector’ only. 2012 - Mini 2009 - Equipped 6.5 inch screen with Visual boost...
Return to the OEM mode in any modes. MENU If you visit car service center, you can lock System the all functions of IW04B-N. Locking / Press the button 10 seconds long. It is only possible to use the OEM functions...
Rear View PIP (External Rear View Camera) 1. Rear, AV1 PIP MODE Push the button right 2 seconds long You can use this function only for 3 modes. (Full, PIP Mode1, PIP Mode2)
Settings For BMW Button Function Operation Enter into the OPTION Press the button 5 seconds long. setting menu Back to previous BACK Press the button short. menu Select the menu Selection Press the button short. and setting values. Move the menu- Turn the dial Move the pointer and setting pointer and adjust...
Settings 4. Rear view camera settings - Parking guide lines = Adjust position of parking guide lines and select the lines ‘ON or OFF’. - Parking distance control = Adjust the position of parking distance control sensors to ‘LEFT or RIGHT’ and select the PDC ‘ON or OFF’. - Image display = Adjust the values of brightness and contrast Red-Green-Blue colors of Rear view camera display.
Settings 6. Automatic activation function(AV1) - Shift gear from reverse to drive - Shift gear from parking to drive * When you shift gear ‘from reverse to drive’ or ‘from parking to drive’, it just works automatically during the activation time you selected. 7.
Settings (SURROUND VIEW OPTION) Keep the rear camera view - Shift gear from reverse to drive - Shift gear from parking to drive * When you shift gear ‘from reverse to drive’ or ‘from parking to drive’, it just works during the activation time you selected.
- Factory default = Reset all setting values to factory default setting. 9. System information - Mode name : IW04B-N - Firmware date : 2016 – 08 – 12 (Latest firmware date) - = You can check the current firmware version date.
Settings 10. Information of Dip switch settings * You can check the current positions of dip switch settings. ex 1) ex 2) Actual DIP switch values. (→) Actual DIP switch values. (→) Appears on the setting menu. (↓) Appears on the setting menu. (↓)
Page 24
Copyright ⓒ indiwork. All Rights Reserved.