Page 1
Release Date: 2016 - 08 - 01 Instruction Manual High-Definition Link for 2015 Audi A6 FACELIFT IW04A-4G Model Name IW04A-4G Latest Firmware Date 2016 - 07 - 26 Manual Version Rev. 1.4 Language English...
Navigation(GPS) box_related • When you connect the power wires(B+, ACC) to the navigation(GPS) box, the ‘NAVI 12V OUT' wire supported by IW04A-4G should be spliced with an ACC wire of navigation box. • After installation is done, select an applicable navigation(GPS) box model in the 'Navigation model selection menu' of setting mode.
Dimension Length : 91 mm Height : 22 mm Width : 142 mm ⓐ ⓑ ⓒ ⓓ ⓔ Exterior ⓐ DIP SWITCH ⓑ AV IN / OUT ⓒ TOUCH IN (Not Used) ⓓ MODE ⓔ POWER / CAN ⓕ HDMI IN ⓖ...
Power / CAN Cable LVDS Cable LVDS PCB HDMI Cable AV IN / OUT Cable 5-pin Micro USB Cable Optional Parts (sold separately at the indiwork) HDMI Cable HDMI Extender Mode Switch (Male to Male) (For stick type HDMI device)
Full Installation Diagram MMI Pin Specification GND Input B+ Power Input ※ Optional External Devices NAVI 12V Power Output (For Navigation) Mode GND Output Switch (optional) RV-CAM Video Input External Rear View 12V Power Output & GND Output(RV-CAM Power) Camera LS CAN wires Reverse Signal Detection(optional) MMI 4G Plus &...
HDMI Connection Diagram HDMI Device HDMI Device HDMI IN 5V USB NAVI IN UART I/F LVDS OUT HDMI IN 5V USB NAVI IN UART I/F LVDS OUT POWER POWER HDMI HDMI HDMI HDMI (5V-1A Power output for HDMI Device) (5V-1A Power output for HDMI Device) (Male) (Female) (HDMI Extender)
Navigation Connection Diagram (N-LINK) Navigation Connection Diagram (X1 CUBE) Navigation(GPS) Box Navigation(GPS) Box HDMI IN 5V USB NAVI IN UART I/F LVDS OUT HDMI IN 5V USB NAVI IN UART I/F LVDS OUT POWER POWER HDMI HDMI Touch screen panel Touch screen panel (USB Cable is connected with the ‘N-Link’, only) iNAVI –...
(HDMI to HDMI) ↑ MYVI South Korea MS1400 Digital OFF(↓): 1, 2, 3 HDMI Cable ON(↑) : 4 (HDMI to HDMI) • The 'IW04A-4G(HD-Link)' supports navigation(GPS) box models equipped with 'Digital video output'. • It does not support the 'RGB video signals'.
Hazard Module Connection POWER / CAN AV IN / OUT DIP SWITCH MODE A6, A7 – 5PIN Hazard connector New Version Module Hazard Module (4-Pin) PIN #1 = Hazard(-) (Blue/White) (For IW04-MB14) IR IN (20 cm) (100 cm) *Hazard Module is just available with ‘Smart Drive function of N-Link’ navigation in South Korea.
LVDS Connection Diagram LVDS Connection HDMI IN 5V USB NAVI IN UART I/F LVDS OUT POWER MMI 4G Plus & 4G Head Unit HDMI • 'Genuine(OEM) LVDS connector' should be connected to 'LVDS IN / OUT PCB'. • ‘Provided LVDS connector' should be connected to the head unit instead to the genuine connector.
Body Connector specifications MODE TOUCH-IN DIP SWITCH AV IN / OUT POWER / CAN Length: 20 cm Length: 100 cm Length: 150 cm BATTERY POWER INPUT RV-CAM VIDEO INPUT GND(RV-CAM VIDEO) GND INPUT RV-CAM POWER OUT GND OUTPUT(RV-CAM) AUDI MMI REVERSE DETECTION IR OUT NAVI 12V POWER OUTPUT...
Car Models Specific Models Year A6 Facelift 2015 - A7 Facelift 2015 - IW04A-4G is used in combination with Audi MMI(Multi Media Interface) system. - MMI navigation (4G) The IW04A-4G supports the Audi Original screen equipped with ‘4 pin LVDS round connector’ only.
< OEM → AV2 > Press the button 4 times consecutively. If you visit car service center, you can System lock the all functions of IW04A-4G. Locking / Press the button 10 seconds long. It is only possible to use the OEM Unlocking functions under it is locked.
Activation by original buttons of Audi MMI 4G Button Function Operation Enter into the MENU(SETUP) Press the button 5 seconds long. setting menu Back to previous BACK(RETURN) Press the button short. menu Select the menu Selection Press the button short. and setting values.
Settings 4. Rear view camera settings - Parking guide lines = Adjust position of parking guide lines and select the lines ‘ON or OFF’. - Parking distance control = Adjust position of parking distance control sensors to ‘LEFT or RIGHT’ and select the PDC ‘ON or OFF’. - Image display = Adjust the values of brightness and contrast Red-Green-Blue colors of Rear view camera display.
Settings 6. Automatic activation function(AV1) - Shift gear from reverse to drive - Shift gear from parking to drive * When you shift gear ‘from reverse to drive’ or ‘from parking to drive’, it just works automatically during the activation time you selected. 7.
Settings (SURROUND VIEW OPTION) Keep the rear camera view - Shift gear from reverse to drive - Shift gear from parking to drive * When you shift gear ‘from reverse to drive’ or ‘from parking to drive’, it just works during the activation time you selected.
- Factory default = Reset all setting values to factory default setting. 9. System information - Mode name: IW04A-4G - Firmware date: 2016 - 04 - 14 (Latest firmware date) - = You can check the current firmware version date.
Settings 10. Information of Dip switch settings * You can check the current positions of dip switch settings. ex 1) ex 2) Actual DIP switch values. (→) Actual DIP switch values. (→) Appears on the setting menu. (↓) Appears on the setting menu. (↓)
Page 23
Copyright ⓒ indiwork. All Rights Reserved.