Panasonic WV-SFN480PJ Operating Instructions Manual page 86

11 Configure the settings relating to images and audio [Image/Audio]
•
QVGA, VGA, 320x180, 640x360, 320x320, and 640x640: 64kbps - 4096kbps*
•
800x600: 128kbps* - 4096kbps*
•
1280x960, 1280x720 and 1280x1280: 256kbps* - 8192kbps*
•
1920x1080 and 1600x1200: 512kbps* - 14336kbps*
•
2048x1536: 1024kbps* - 24576kbps*
•
2560x1920 and 2560x1440: 1536kbps* - 24576kbps*
•
2048x2048: 1536kbps* - 24576kbps*
•
2816x2816: 2048kbps* - 24576kbps*
•
2992x2992: 3072kbps* - 30720kbps*
When "VBR" is selected for "Transmission priority"
•
QVGA, VGA, 320x180, 640x360, 320x320, and 640x640: 64kbps - 30720kbps*
•
800x600: 128kbps* - 30720kbps*
•
1280x960, 1280x720 and 1280x1280: 256kbps* - 30720kbps*
•
1920x1080 and 1600x1200: 512kbps* - 30720kbps*
•
2048x1536: 1024kbps* - 30720kbps*
•
2560x1920 and 2560x1440: 1536kbps* - 30720kbps*
•
2048x2048: 1536kbps* - 30720kbps*
•
2816x2816: 2048kbps* - 30720kbps*
•
2992x2992: 3072kbps* - 30720kbps*
Note
•
The H.264 bit rate is restricted by "Bandwidth control(bit rate)" on the [Network] tab on the "Network"
page (®page 144). For this reason, the bit rate may be lower than the value when any value with an
asterisk (*) on the right is selected.
[Image quality]
Select the image quality of H.264 images from the following.
•
When "Transmission priority" is set to "Constant bit rate" or "Best effort": Low(Motion priority)/
Normal/ Fine(Image quality priority)
•
VBR: 0 Super fine/ 1 Fine/ 2/ 3/ 4/ 5 Normal/ 6/ 7/ 8/ 9 Low
•
Default: 1 Fine
Note
•
When "Constant bit rate", "Best effort", or "VBR" is selected for "Transmission priority", this setting is
available.
[Refresh interval]
Select an interval (I-frame interval; 0.2 - 5 seconds) to refresh the displayed H.264 images.
If using under a network environment with frequent error occurrences, shorten the refresh interval for H.264
to diminish image distortions. However, the refresh interval may be longer than the set value.
0.2s/ 0.25s/ 0.33s/ 0.5s/ 1s/ 2s/ 3s/ 4s/ 5s
•
Default: 1s
[Transmission type]
Select the transmission type of H.264 images from the following.
•
Unicast port (AUTO): Up to 14 users can access a single camera concurrently. "Unicast port1(Image)"
and "Unicast port2(Audio)" will automatically be selected when transmitting images and audio from the
camera. When it is unnecessary to fix the port number for H.264 image transmission such as when using
in a particular LAN environment, it is recommended to select "Unicast port (AUTO)".
•
Unicast port (MANUAL): Up to 14 users can access a single camera concurrently. It is necessary to select
"Unicast port1(Image)" and "Unicast port2(Audio)" manually to transmit images and audio from the camera.
86 Operating Instructions