Panasonic WV-SFR631L Installation Manual

Installation Guide
Included Installation Instructions
Network Camera
WV-SFR631L/WV-SFR611L
Model No.
WV-SFN631L/WV-SFN611L
(This illustration represents WV-SFN631L)
● This manual describes the installation procedures, network camera installation, cable connections,
and the angle of view adjustment.
● Before reading this manual, be sure to read the Important Information.
● This manual describes how to install the network camera using model WV-SFN631L as an
example.
For U.S. and Canada: For Europe and other countries:
Panasonic System Communications Panasonic Corporation
Company of North America,
http://panasonic.net
Unit of Panasonic Corporation
of North America
www.panasonic.com/business/ Panasonic System Networks Co., Ltd.
For customer support, call 1.800.528.6747 Fukuoka, Japan
Two Riverfront Plaza, Newark, NJ 07102-5490
Authorised Representative in EU:
Panasonic Canada Inc.
Panasonic Testing Centre
5770 Ambler Drive, Mississauga,
Panasonic Marketing Europe GmbH
Ontario, L4W 2T3 Canada
Winsbergring 15, 22525 Hamburg, Germany
(905)624-5010
www.panasonic.ca
Panasonic System Networks Co., Ltd. 2013
PGQX1457YA Cs0114-1024 Printed in China
Major operating controls
The component names of the camera are as follows. Refer to the illustration when installing or
adjusting the camera.
Screen display
12 V DC power Direction marker for installation
top (TOP)
supply terminal ( TOP)
● Points up when installing to a wall.
MONITOR OUT terminal
(factory shipment:
NTSC monitor)
Direction marker
for installation
(FRONT )
● FRONT must positioned
in front of the camera
(on the Panasonic logo
side).
Auto focus (AF)
button
TELE button
(moves the camera to the "Tele" side)
WIDE button
(moves the camera to the "Wide" side)
SD slot 1 (SD1)
SD slot 2 (SD2)
SD ON/OFF button
*1 SDXC/SDHC/SD memory card is described as SD memory card.
*2 Depending on the scanning application used, the Data Matrix may not be able to be
read correctly. In this case, access the site by directly entering the following URL.
http://security.panasonic.com/pss/security/support/qr_sp_select.html
Standard accessories
Important Information ............................... 1 pc. CD-ROM*
Installation Guide (this document) ............ 1 set Code label*
Warranty card ........................................... 1 set
*1 The CD-ROM contains the operating instructions and different kinds of tool software programs.
*2 This label may be required for network management. The network administrator shall retain the
code label.
The following parts are used during installation procedures.
A Attachment plate .................................. 1 pc. E External I/O terminal plug .................... 1 pc.
B Bit ......................................................... 1 pc. F MONITOR OUT conversion plug ......... 1 pc.
C Template A (for the attachment plate) 1 sheet. G Cable tie ............................................. 2 pcs.
D Power cord plug ................................... 1 pc.
B D
(Screw size 6.35 mm
{1/4 inches} torx wrench)
* The external I/O terminal plug and power cord plug are attached to the camera.
Enclosure
Camera
Camera fixing screw
IR LED
Dome cover Light-blocking
Tilting table
rubber ring
Azimuth
adjustment ring
NTSC/PAL switch
● The MONITOR OUT terminal output can be switched for the NTSC monitor/PAL monitor.
IMPORTANT:
● This is valid if the [Monitor out] is set to [Switch priority] ([Switch priority] is selected by
default).
For details, refer to the Operating Instructions (included in the CD-ROM).
Data Matrix: To
INITIAL SET button
our website
*2
● How to initialize the camera
Follow the steps below to initialize the network camera.
T urn off the power of the camera. When using a PoE hub, disconnect the LAN cable from
q
the camera. When using an external power supply, disconnect the power cable plug from
the 12 V DC power supply terminal.
T urn on the power of the camera while holding down the INITIAL SET button, and then
w
keep holding down the button for 5 seconds or more. About 2 minutes later, The camera will
start up and the settings including the network settings will be initialized.
IMPORTANT:
● When the camera is initialized, the settings including the network settings will be initial-
ized. Note that the CRT key (SSL encryption key) used for the HTTPS protocol will not
be initialized.
● Before initializing the settings, it is recommended to write down the settings in advance.
● Do not turn off the power of the camera during the process of initialization. Otherwise, it
may fail to initialize and may cause malfunction.
ACT indicator
● When data is being sent via the network camera
LINK indicator
● When the camera is able to communicate with the connected device Lights orange
SD MOUNT indicator
*1
● When an SD memory card is inserted and could
be recognized
● When data can be saved after the SD memory card is
inserted and the SD ON/OFF button is pressed
● When data can be saved to the SD memory card
● When the SD memory card is removed after holding down
the SD ON/OFF button for about 2 seconds
● When data cannot be saved to the SD memory card because
an abnormality was detected or the SD memory card is
configured not to be used
SD ERROR/AF indicator
● When AF (Auto Focus) operation is being executed
● When the set is being started
● When an SD memory card is recognized normally
● When an abnormality is detected in both SD1 and
SD2 cards after the camera has started
● When an abnormality is only detected in the SD1 card
after the camera has started
● When an abnormality is only detected in the SD2 card
after the camera has started
Making connections
Turn off each system's power supply before making a connection. Before making connections,
1 ................................................ 1 pc.
prepare the required peripheral devices and cables.
2 .............................................. 1 pc.
Note:
● Since the connector storage section
does not have a sufficient space, use
audio cables and a LAN cable that do
not exceed the sizes described in the
illustrations.
Connect a LAN cable (category 5 or better, straight, STP: For Europe)
(of them, 1 for spare)
Connect a LAN cable (category 5 or better, straight, STP: For Europe) to the network connector.
E
IMPORTANT:
● Use all 4 pairs (8 pins) of the LAN cable.
● The maximum cable length is 100 m {328 feet}.
● Make sure that the PoE device in use is compliant with IEEE802.3af standard.
● When connecting both the 12 V DC power supply and the PoE device for power
supply, 12 V DC will be used for power supply.*
* If a 12 V DC power supply and a PoE hub or router are used at the same time,
network connections may not be possible. In this case, disable the PoE settings.
Refer to the operating instructions of the PoE hub or router in use.
● When the LAN cable is disconnected once, reconnect the cable after around
2 seconds. When the cable is quickly reconnected, the power may not be supplied
from the PoE device.
A Attachment plate
(accessory)
Panning table
Connect an external amplifier-embedded speaker to the audio output cable
Connect a stereo mini plug (ø3.5 mm) (Audio output is monaural.). Use an external powered speaker.
● Output impedance
● Recommended cable length : Less than 10 m {32.8 feet}
● Output level
IMPORTANT:
● Connect/disconnect the audio cables and turn on the power of the camera after turning
off the power of the audio output devices. Otherwise, loud noise may be heard from
the speaker.
● Make sure that the stereo mini plug is connected to this cable. When a monaural mini
plug is connected, audio may not be heard.
When connecting a monaural speaker with amplifier, use a locally procured conversion
cable (mono-stereo).
Microphone/line input cable
Connect a monaural mini plug (ø3.5 mm).
● Input impedance: Approx. 2 kΩ (unbalanced)
● Recommended cable length: Less than 1 m {3.28 feet} (for microphone input)
● Recommended microphone: Plug-in power type (option)
Blinks green (accessing)
● Recommended sensitivity of microphone: –48 dB ±3 dB (0 dB=1 V/Pa,1 kHz)
● Input level for the line input: Approx. –10 dBV
When connecting to a network using a PoE hub
Before starting the installation, check the entire system configuration. The following illustration
Lights off → Blinks green →
gives a wiring example of how to connect the camera to the network via a PoE device (hub).
Lights off
Lights off → Lights green
Adjustment monitor
Powered speaker
Lights green
Lights green → Blinks green → Lights off
Lights off
Microphone
Blinks red (Interval of 1 time/ second)
Powered speaker
Lights red
Lights red → Lights off
Lights red
Lights red → Blinks red
Microphone
(Interval of 1 time/ 3 seconds)
Recommended total extended
Lights red → Blinks red
cable length*
(Interval of 2 times/ 3 seconds)
Connect the alarm input/output cable
Connect the cables of external devices to the EXT I/O terminal plug (accessory).
When connecting an external device, remove 8 mm - 9 mm {5/16 inches - 11/32 inches} of
q
the outer jacket of the cable and twist the cable core to prevent the short circuit first.
Specification of cable (wire): 20 AWG - 26 AWG, Single core, twisted
Push down the button of the desired terminal on the external I/O terminal plug with a ball-
w
point pen, and release the button when the cable of the external device is fully inserted
9 mm
{11/32 inches} into the terminal hole.
Note:
● Check whether the stripped part of the wire is not exposed and is securely connected.
Example of Example of LAN cable
<Ratings>
audio cable connector connector
● ALARM IN1(DAY/NIGHT IN), ALARM IN2, ALARM IN3
Input specification : No-voltage make contact input (4 V - 5 V DC, internally pulled up)
OFF
ON
● ALARM OUT, AUX OUT
Output specification : Open collector output (maximum applied voltage: 20 V DC)
Open
Close
* The default of EXT I/O terminals is "Off".
button
IMPORTANT:
● Do not connect 2 wires or more directly to a terminal. When it is necessary to con-
nect 2 or more wires, use a splitter.
● Off, input, and output of the external I/O terminal 2 and 3 can be switched by con-
figuring the setting. Refer to the Operating Instructions on the provided CD-ROM
for further information about the EXT I/O terminal 2 and 3 (ALARM IN2, 3) settings
("Off", "Alarm input", "Alarm output" or "AUX output").
● Install external devices so that they do not exceed the rating of the network camera.
-
● When using the EXT I/O terminals as the output terminals, ensure they do not
+
cause signal collision with external signals.
Connect the power cable
Caution:
● As necessary, use a cable tie
(accessory) to tie the cables ● A READILY ACCESSIBLE DISCONNECT DEVICE SHALL BE INCORPORATED
together. TO THE EQUIPMENT POWERED BY 12 V DC POWER SUPPLY.
● ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL 1310/CSA 223) or
LIMITED POWER SOURCE (IEC/EN/UL/CSA 60950-1).
Connect the output cable to the power cable plug (accessory).
: Approx. 600 Ω (unbalanced)
L oosen the screw of the power cable plug (accessory), strip 3 mm to 7 mm {1/8 inches to
q
: –20 dBV
9/32 inches} from the end of the wire, twist the stripped part of the wire sufficiently to avoid
short circuit, and then connect the output cable to the power cable plug (accessory).
Tighten the screw of the power cable plug. (Recommended tightening torque: 0.34 N·m
w
{0.25 lbf·ft})
Note:
● Check whether the stripped part of the wire is not exposed and is securely con-
nected.
● When connecting an external power supply to the camera, use the 16 AWG to 24
AWG single-wired or stranded wired cables.
IMPORTANT:
● The 12 V DC power supply shall be insulated from the commercial AC power.
● Be sure to use the power cable plug provided with this product.
Less than 10 m {32.8 feet} (for line input)
● Be sure to fully insert the power cable plug into the 12 V DC power supply terminal.
●Supply voltage: 2.5 V ±0.5 V
Otherwise, it may damage the camera or cause malfunction.
● When installing the camera, make sure that excessive force is not applied to the
power cable.
● Be sure to use an AC adaptor compliant with the Specifications (written in the indi-
cation label on the bottom side of this unit) regarding power source and power con-
sumption.
PoE device (hub)
<Required cable>
LAN cable (category 5 or better, straight, STP: For Europe)
LAN cable
Use a LAN cable (category 5 or better, cross) when directly connecting the camera to a PC.
(category 5 or better, straight,
*1 Recommended cable length from the speaker
STP: For Europe)
Recommended cable length from the microphone : less than 1 m {3.28 feet}
PC
LAN cable (category 5
or better, straight,
IMPORTANT:
STP: For Europe)
● The adjustment monitor is used for checking the adjustment of the angular field of
view when installing the camera or when servicing. It is not provided for recording/
LAN cable
monitoring use.
(category 5 or better, straight,
● Depending on the monitor, some characters (camera title, preset ID, etc.) may not
STP: For Europe)
be displayed on the screen.
● Use a switching hub or a router which is compliant with 10BASE-T/100BASE-TX.
Adjustment monitor
● If a PoE hub is not used, each network camera must be connected to a 12 V DC
power supply.
● When using 12 V DC, power supply from a PoE hub or router is not required.
1
: Open or 4 V - 5 V DC
: Make contact with GND (required drive current: 1 mA or more)
: 4 V - 5 V DC by internal pull-up
: Output voltage 1 V DC or less (maximum drive current: 50 mA)
GND
ALARM IN3, AUX OUT
(Alarm input terminal 3, AUX output terminal)
ALARM IN2, ALARM OUT
(Alarm input terminal 2, Alarm output terminal)
ALARM IN1, DAY/NIGHT IN
(Alarm input terminal 1, DAY/NIGHT input terminal)
E External I/O terminal plug (accessory)
: less than 10 m {32.8 feet}