Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Analytic Systems PWS1005W
Summary of Contents for Analytic Systems PWS1005W
- Page 1 INSTALLATION & OPERATION MANUAL PWS1005W POWER SUPPLY An ISO9001 Registered Company Battery Chargers • Inverters • Power Supplies • Voltage Converters 8128 River Way, Delta B.C. V4G 1K5 Canada T. 604.946.9981 F. 604.946.9983 TF. 800.668.3884 (US/CANADA) www.analyticsystems.com...
- Page 2 Copyright (2005-2020) Analytic Systems Ware (1993) Ltd. Revised - Feb 24, 2020...
- Page 3 Analytic Systems does not recommend the use of any of its products in direct patient care. Examples of devices considered to be life support devices are neonatal oxygen...
-
Page 4: Table Of Contents
• Table of Contents • Introduction • Box Contents • Main Parts • Operation • Output Fuse Replacement • Installation • Troubleshooting • Product Options • Specifications • Warranty Copyright (2005-2020) Analytic Systems Ware (1993) Ltd. Revised - Feb 24, 2020... -
Page 5: Introduction
Introduction The PWS1005W power supply provides up to 1000 watts of precision power to a 12, 24, 32, 36, 48, or 72 (Rail) VDC electrical system from a 110 or 220 VAC source. Designed for service in the most unforgiving environments, the PWS1005W has an operational temperature range spanning -40°C to +55°C. -
Page 6: Main Parts
Main Parts Front Panel Power Switch DC Output Connection: 8AWG TEW-type stranded wire, AC Input Connection: 3.05m bare copper leads (Positive: Red and /10.00ft P3x14AWG power cord Negative: Black) encased in a sealcon ending in a NEMA 5-15;125VAC gland plug encased in a sealcon gland LED Operational Indicators Input Fuse: MDA 25 Amp... -
Page 7: Operation
Operation This unit is designed for simple operation. Before operating the unit, it must be properly installed and connected to the power source and load. See Installation for more details. TO TURN THE UNIT ON: Move the Power Switch to the ON position. The alarm buzzer will sound briefly and the POWER LED will begin glowing green indicating the power supply is supplying the load. - Page 8 1 inch (2.54 cm) of clearance surrounding the unit for adequate cooling. The PWS1005W is designed to meet IP66 rating,and is resistant to water spray from any direction. These units can be mounted in wet locations but are not suitable for submersion.
-
Page 9: Output Fuse Replacement
Output Fuse Replacement The power supply is protected from damage by reverse polarity connection by output fuses. If the load is connected to the unit in the wrong polarity, the output fuse(s) will blow to protect the power supply. Afterwards, the fuses must be replaced for normal unit operation. See the specifications section for rating and make fuses. -
Page 10: Troubleshooting
Troubleshooting This unit is fitted with 5 LED indicators and an alarm buzzer to display and diagnose any malfunctions. In the event of a malfunction, the unit will sound the buzzer to alert you before shutting itself down. You should then immediately check which LEDs are glowing to determine the cause of the alarm. - Page 11 Battery Backup Option The Battery Backup Option allows you to connect a battery to the output of your unit to serve as a backup power source in the event of power failure. The Battery Backup circuit is designed so the diodes are reversed biased in normal operation and forward biased in event of power failure.
- Page 12 Load Sharing Option The Load Sharing Option allows you to connect two or more units in parallel, allowing them to share in supplying current to the load(s). Connecting units together this way has many advantages, it reduces stress on each individual power supply and in addition, the load can draw greater current than from a single unit.
-
Page 13: Specifications
Specifications Input Nominal Voltage 110 and 220 VAC (Auto-switching) Actual Voltage 90 - 133 VAC and 180 - 264 VAC Current 13.1 A (Maximum @ 90 VAC in) Fuse MDA 25 Amp Input Frequency 49 - 405 Hz Noise on Input <... -
Page 14: Warranty
Output Connection 3.0 m / 10.0ft 3xAWG14 power cord with NEMA 5-15 compatible plug * Specifications subjects to change without notice. Designed and manufactured by: ANALYTIC SYSTEMS WARE (1993) LTD. 8128 River Way p. 604.946.9981 f. 604.946.9983 Delta, B.C. V4G 1K5 Canada tf. - Page 15 2 Years from date of manufacture for non-standard or OEM products 1 Year from date of manufacture for encapsulated products. 3. Analytic Systems will determine eligibility for warranty from the date of purchase shown on the warranty card when returned within 30 days, or...
- Page 16 DESIGNED AND MANUFACTURED BY 800-668-3884 604-946-9983 Support@analyticsystems.com www.AnalyticSystems.com Battery Chargers • Inverters • Power Supplies • Voltage Converters 8128 River Way Delta, BC V4G 1K5 | Canada Register Products Online | www.analyticsystems.com/support/warranty-registration...
Need help?
Do you have a question about the PWS1005W and is the answer not in the manual?
Questions and answers