1080p indoor/outdoor ip camera with infrared and 802.3af support (27 pages)
Summary of Contents for Ubiquiti UVC-G4-PRO
Page 1
UVCG4PRO Quick Start Guide Package Contents Camera Tightening Tool Pole Mount Bracket Screw Anchors (Qty. 2) SelfTapping Screws (Qty. 2) Machine Screws (Qty. 2) Installation Requirements Polemounting: Two metal straps (not included) Shielded Category 5 (or above) cabling with drain wire should be used for all outdoor wired Ethernet connections and should be grounded through the AC ground of the PoE. We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrialgrade, shielded Ethernet cable from Ubiquiti. For more details, visit ui.com/toughcable Surge protection should be used for all outdoor installations. We recommend that you use two Ethernet Surge Protectors, model ETHSP, one near the camera and the other at the entry point to the building. The ETHSP will absorb power surges and safely discharge them into the ground.
Ethernet Port 10/100/1000 RJ45 port connects to an 802.3af/802.3at switch for PoE power and data. Reset Button The Reset button serves two functions: Reboot Press and release the Reset button quickly. Restore to Factory Defaults Press and hold the Reset button for 1020 seconds while the camera is powered on. Cable Gland Creates a tight seal around the Ethernet cable to prevent water from damaging the RJ45 port. LED Ring White Ready for configuration. Flashing White Initializing. Heartbeat Flashing White Device is being reset to factory defaults. Indicates the device has been successfully Blue adopted into a network and is working properly. Rotating Blue Motion detected. Firmware upgrade in progress. Device is busy; do Alternating White/Blue not touch or unplug it. Repeating Off/White/Blue Recovery mode. Flashing Red Recording. Device failure; network error. If this occurs, we recommend rebooting the device. Before You Begin Remove the sticker from the bottom of the Mounting Base. Installation Overview...
To install the camera, please follow the instructions of the following sections in this order: 1. Hardware Installation 2. Connecting Power 3. UniFi Protect App 4. Adjusting the Camera View Hardware Installation The camera can be mounted on a wall, ceiling, or pole. Follow the appropriate steps for your installation: Wall/Ceiling Mount 1. 2. ...
Page 11
8. IMPORTANT: For proper weather sealing, the Cable Gland must fit securely within the Adjustable Base when the camera is mounted. Ensure that the Cable Gland is securely seated during installation and cable routing. 9. ...
Note: When you first launch UniFi Protect, the app will prompt you to enable Bluetooth and other features necessary to provide the best user experience possible. Please allow these features and permissions for proper app functionality. Adjusting the Camera View 1. ...
Electrical Safety Information 1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified may result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed. 2. There are no operator serviceable parts inside this equipment. Service should be provided only by a qualified service technician. Limited Warranty ui.com/support/warranty The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and, where applicable, specify arbitration instead of jury trials or class actions. Compliance Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operations of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. ISED Canada CAN ICES3(A)/NMB3(A) Australia and New Zealand Warning: This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interference. CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it.