Download
Share
Print this page
Prestige APS787Z Installation And Reference Manual
  1. Manuals
  2. Brands
  3. Prestige Manuals
  4. Security System
  5. APS787Z
  6. Installation and reference manual

Prestige APS787Z Installation And Reference Manual

Vehicle security / remote start system
Hide thumbs Also See for APS787Z:

Advertisement

Quick Links

Download this manual
Thank you for trus�ng Pres�ge products! If you are a consumer, please note:
Professional installation is strongly recommended.
This manual assumes the installer has adequate knowledge of the following exper�se. Therefore, it does not
cover these topics in detail:
•
12-volt electronics
•
Testing and verifying circuits
•
Making safe and lasting wiring connections
•
Factory ignition, power, lighting, data bus and sensing systems
•
Factory systems and components to avoid
•
Safe wire routing, circuit protection and product placement
•
Access to vehicle-specific technical information
In addi�on, this manual assumes the installer has the proper tools, skill and facilities to perform a professional installa�on.
Performing an improper installation could result in damage to the vehicle or its components, improper system function,
unsafe vehicle operation or physical injury. Such instances would not be covered by the vehicle manufacturer's warranty,
nor by Voxx Electronics, Inc.
Detailed Descriptions
2
Wire Harness Colors and Functions
Power Connector
2
Alarm / No�fica�on Connector
3
Input / Output Connector
4
7
External Components
7
Shock Sensor
7
RF Antenna Kit
7
Data Bus Interface (FLCART / DBI)
7
Telema�cs
8
Setup Options
8
Remote Programming
Security Control
9
Remote Start Control
13
17
Nega�ve Output Control (NOC)
AUX Output Control
19
PIC Input Control
20
21
System Operation
21
Manual Transmission Mode
22
Remote Operation
2020 Voxx Electronics Corpora�on. All rights reserved.
APS787Z
Vehicle Security / Remote Start System
Installation and Reference Guide
Quick Reference
23
Setup Options
23
Programming Mode Entry / Exit
24
Feature Bank Options
25
Programming & Diagnostics
Data Port Protocol Selec�on
25
Tach Func�on
25
Dome Light Delay
25
2 / 4 Hour Timer
26
Turbo Timer
26
Silent Arm and Disarm
26
27
User Selectable LED
27
Adjus�ng Shock Sensor
27
Troubleshoo�ng Trigger Zones
27
Troubleshoo�ng Remote Start
28
Alarm Override Procedures
29
Wiring Diagrams
Door Lock Connec�ons
29
Starter Kill Relay
32
33
Full System Connections
APS787Z_RevD_07/20

Advertisement

loading
Need help?

Need help?

Do you have a question about the APS787Z and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Prestige APS787Z

Summary of Contents for Prestige APS787Z

  • Page 1 APS787Z Vehicle Security / Remote Start System Installation and Reference Guide Thank you for trus�ng Pres�ge products! If you are a consumer, please note: Professional installation is strongly recommended. This manual assumes the installer has adequate knowledge of the following exper�se. Therefore, it does not cover these topics in detail: •...
  • Page 2 Detailed Descriptions: Wire Harness Colors and Func�ons Power Connector (8-pin High-Current Connector) See page 33 for the full system diagram. These wires are listed in order of their placement in the harness connector. 1. RED/BLACK – Ignition 3, Flex Relay Input (Internal Relay Pin 87) The RED/BLACK wire is used to supply the Pin 2 - PINK Flex Relay Output.
  • Page 3 Detailed Descriptions: Wire Harness Colors and Func�ons Power Connector (8-pin High-Current Connector) (Cont) See page 33 for the full system diagram. These wires are listed in order of their placement in the harness connector. 7. PURPLE – Accessory Output (+) At its default setting, the Purple wire supplies 12-Volt (+) to the vehicle’s accessory wire to power vehicle accessories during remote start.
  • Page 4 Detailed Descriptions: Wire Harness Colors and Func�ons Input / Output Connector (22-pin connector) See page 33 for the full system diagram. These wires are listed in order of their placement in the harness connector. 1. ORANGE – Starter Kill Output (-) The ORANGE wire supplies Ground (-) when the alarm is armed and when the remote start is ON.
  • Page 5 Detailed Descriptions: Wire Harness Colors and Func�ons Input / Output Connector (22-pin connector) (Cont.) See page 33 for the full system diagram. These wires are listed in order of their placement in the harness connector. 10. ORANGE/BLACK – Parking Brake Input (-) (PIC4) The ORANGE/BLACK wire connects to the vehicle’s parking brake wire to supply parking brake status for remote start.
  • Page 6 Detailed Descriptions: Wire Harness Colors and Func�ons Input / Output Connector (22-pin connector) (Cont.) See page 30 for the full system diagram. These wires are listed in order of their placement in the harness connector. 20. RED – Door Lock (-) (NOC 10) The RED wire supplies Ground (-) when the Lock func�on is ac�vated from the remote control or system.
  • Page 7 Detailed Descriptions: External Components Shock Sensor The shock sensor plugs into a 4-pin connector on the Pres�ge module. It should be securely a�ached to a vehicle surface or sturdy wire harness. Tes�ng takes place a�er all connec�ons are made and the system is powered up. Refer to Quick Reference: System Diagnostics on page 26 for instruc�ons on tes�ng and adjus�ng the shock sensor.
  • Page 8 Detailed Descriptions: Setup Op�ons Bank 1: Add / Remove Remote Controls Remote programming is located in Feature Bank 1. This system will Auto Program basic func�ons of the remote with one (1) bu�on press. Basic func�ons are channels 1-3, Lock, Unlock, and Trunk / Start. Feature Bank 1 Descrip�on 1 Auto Program/Lock...
  • Page 9 Detailed Descriptions: Setup Op�ons Security Control (Bank 2) See page 23 for Programming Instruc�on. Op�ons Feature Bank 2 1 Chirp 2 Chirp 3 Chirp 4 Chirp 5 Chirp 6 Chirp 1 Lock / Unlock Func�on 500ms 3.5sec 500ms L, DBL UL DBL L, 500ms UL DBL L, DBL UL 500ms L, 350ms UL...
  • Page 10 Detailed Descriptions: Setup Op�ons Security Control (Bank 2) (cont.) See page 23 for Programming Instruc�on. Feature 5: Auto ReLock Setting Func�on: Set the doors to re-lock if the system has been accidentally disarmed. Setting Choices: • Option 1 - Auto ReLock is disabled. •...
  • Page 11 Detailed Descriptions: Setup Op�ons Security Control (Bank 2) (Cont.) See page 23 for Programming Instruc�on. Feature 10: Driver Priority Unlock Func�on: Set the behavior of unlock outputs when arming and disarming the system. Setting Choices: • Option 1 - Unlock pulse will be on the Green wire unlock output only. •...
  • Page 12 Detailed Descriptions: Setup Op�ons Security Control (Bank 2) (Cont.) See page 23 for Programming Instruc�on. Feature 16: Dome Light Delay Timer Func�on: Set the delay timer when using the vehicle's Dome Light as a door trigger. Setting Choices: • Option 1 - OFF / Delay Timer will be OFF or use the programmed �me. See page 25 for dome light delay programming procedure •...
  • Page 13 Detailed Descriptions: Setup Op�ons Remote Start Control (Bank 3) See page 23 for Programming Instruc�on. Op�ons Feature Bank 3 1 Chirp 2 Chirp 3 Chirp 4 chirp 5 Chirp 6 Chirp Pulsed 1 Defrost Output 10min RS Run�me 2 RS Start No�fica�on 3 RS Run�me 15min 20min...
  • Page 14 Detailed Descriptions: Setup Op�ons Remote Start Control (Bank 3) (cont.) See page 23 for Programming Instruc�on. Feature 5: Engine Confirmation Mode Func�on: Determine how the system knows if remote start was successful. Setting Choices: • Option 1 - Determined by measurement from the Purple/White Tach Input wire. •...
  • Page 15 Detailed Descriptions: Setup Op�ons Remote Start Control (Bank 3) (cont.) See page 23 for Programming Instruc�on. Feature 12: Diesel (Pre-Start) Delay Func�on: After remote start ignition is activated, set delay of crank to accommodate diesel engines. Setting Choices: • Option 1 - Vehicle starts immediately a�er remote start igni�on. •...
  • Page 16 Detailed Descriptions: Setup Op�ons Remote Start Control (Bank 3) (Cont.) See page 23 for Programming Instruc�on. Feature 17: Remote Start Activation Func�on: Set remote start to activate with one, two, or three presses from the remote control or pulses detected on the Dark Blue/Black External Activation Input.
  • Page 17 Detailed Descriptions: Setup Op�ons Negative Output Control (NOC) Nega�ve Output Control (NOC) allows the installer to program any NOC output for any NOC op�on. For example, if an installer is not using the GREEN/WHITE Dome Light output, but requires a second Remote Start Status Output, the system can be programmed to change the output type.
  • Page 18 Detailed Descriptions: Setup Op�ons Negative Output Control (NOC) (CONT.) Pulse During Crank This op�on supplies a pulse to crank the engine's starter. This output will pulse for the �ming op�on selected in Feature Bank 3, Feature 11. Pulse After Shutdown This op�on supplies a pulse a�er remote start shutdown only.
  • Page 19 Detailed Descriptions: Setup Op�ons Auxiliary Output Control (AUX Control) Auxiliary (AUX) output control allows each AUX Channel output to be customized to the user or vehicle's need. See the list below for a detailed descrip�on of the available op�ons. AUX Ch. Outputs can only be programmed using the FlashLogic Weblink or Weblink Mobile.
  • Page 20 Detailed Descriptions: Setup Op�ons Programmable Input Control (PIC Control) Programmable Input Control (PIC) allows each PIC input to be customized to the user or vehicle's need. See the list below for a detailed descrip�on of the available op�ons. PIC Inputs can only be programmed using the FlashLogic Weblink or Weblink Mobile.
  • Page 21 Detailed Descriptions: System Opera�on Manual Transmission Mode (Ready Mode) This remote start system is compa�ble with manual transmission vehicles. When Manual Transmission Mode is ac�vated in Feature Bank 3, Feature 10, this system will monitor mul�ple inputs to safely and securely remote start the vehicle. Note: A connection to the vehicle's parking brake and tach signal (Analog or Data) is required.

  • Page 22: Remote Control Operation

    Detailed Descriptions: System Opera�on Remote Control Operation This system is compa�ble with mul�ple different remote configura�ons; one (1) bu�on, five (5) bu�on, and LCD remotes. The matrix below describes how each remote offering will control the basic system func�ons. See Owner's Guide for more detailed informa�on Five Bu�on Remotes (1-Way &...
  • Page 23 Quick Reference: System Programming Programming Mode Entry and Exit Procedure Once the system is installed and powered up, you will use the vehicle igni�on, override bu�on and a programmed remote control to set all system op�ons. Feature op�ons are divided into categories, or Banks, as described throughout this sec�on.
  • Page 24 Quick Reference: Setup Op�ons Bank 1: Transmitter Programming Options See page 8 for a detailed descrip�on. Feature Bank 1 Descrip�on 1 Auto Program/Lock Press Lock bu�on on remote 2 Unlock Press Unlock bu�on on remote 3 Trunk/Start Press Trunk/Start bu�on on remote 4 Ch.
  • Page 25 Note: Programming tach signal via OEM or Telema�cs control is only available on Firmware v1.47 or Higher. Dome Light Delay To program the Prestige system to wait until the dome light turns off before arming: 1. Close all doors. 2. With the vehicle igni�on off, press LOCK, UNLOCK, LOCK ,UNLOCK, LOCK, UNLOCK, LOCK on the remote control. The dash-mounted LED will turn on.

  • Page 26: Turbo Timer

    Quick Reference: Programming & Diagnos�cs 2 /4 Hour Timed Start This module has the ability to start the vehicle automa�cally at �med intervals. This feature can be useful in extremely cold climates where star�ng the engine is the only means to keep the ba�ery charged and fluids warm. The factory preset start �me is four (4) hours.

  • Page 27: Adjusting The Shock Sensor

    Quick Reference: Programming & Diagnos�cs User Selectable LED This feature will control whether the LED is ON or OFF when the system is Armed/Locked. This will be selectable in feature programming OR on-the-fly without entering the programming feature banks. 1. Turn the igni�on ON, OFF, ON, OFF. 2.
  • Page 28 Quick Reference: Alarm Override Procedures Valet Alarm Override The Valet Override procedure will disable the alarm when the remote is not available or has become inopera�ve. If the vehicle door is opened without disarming, the alarm will sound and the vehicle will not start when a�emp�ng to start with the key.

  • Page 29: Door Lock Connections

    Quick Reference: Wiring Diagrams Door Lock Connections Negative-Trigger Door Locks Verification: The vehicle wires register Ground when the Lock and Unlock switches are ac�vated. RED ( - ) Lock Output Lock Vehicle Door Lock Control Relays Unlock GREEN ( - ) Unlock Output Positive-Trigger Door Locks Verification: The vehicle wires register 12V+ when the Lock and Unlock switches are ac�vated.
  • Page 30 Quick Reference: Wiring Diagrams Door Lock Connections Single-Wire Negative Multiplex Door Locks (Relays required) Verification: The vehicle wire registers variable Ground values when the Lock and Unlock switches are ac�vated. Please consult the vehicle-specific wire and loca�on chart for resistor values. Ground Fused +12 Volt RED ( - ) Lock Output...
  • Page 31 Quick Reference: Wiring Diagrams Door Lock Connections Reverse-Polarity Door Locks (Relays required) Verification: The vehicle wires rest at Ground and register 12V+ when the Lock and Unlock switches are ac�vated. Fused +12 Volt Battery Souce RED ( - ) Lock Output Lock To Door Lock Motor Unlock...
  • Page 32 Quick Reference: Wiring Diagrams Starter Kill / Anti-Grind Relay Connections Starter Kill / An�-Grind Relay (Op�onal) To ORANGE - Starter Kill / To Vehicle Ignition Anti-Grind Output (-) From Alarm APS787Z_RevD_07/20...
  • Page 33 Shock Sensor Part #4700033 Ba�ery 12V (+) Black Data TX Blue Warn Away Green Full Trigger Replacement Part #4120459 4180075 185SP 185SP Green Unlock Output (-) (NOC 11) Dk. Blue Trunk Output (-) (NOC 9) Lock Output (-) (NOC 10) Green/Lt.