Prestige APS-122E Installation Manual

Remote control vehicle security system

Hide thumbs Also See for APS-122E:

Owner's manual (8 pages)

Table Of Contents

Table of Contents

Quick Links

Need help?

Do you have a question about the APS-122E and is the answer not in the manual?

Questions and answers

Summary of Contents for Prestige APS-122E

Page 1 Model APS-122E Installation Manual Remote Control Vehicle Security System Table Of Contents: Before You Begin Page 2 Wire Harness Quick View Page 3 Installation Of The Major Components Page 4 7 Pin Main Wire Harness Page 5-6 2 Pin LED/Valet Connector Page 6 3 Pin Door Lock Connector &...
Page 2: Before You Begin
Before You Begin PROFESSIONAL INSTALLATION IS STRONGLY RECOMMENDED Roll down window to avoid locking the keys in the vehicle during installation. Avoid mounting components or routing wires near hot surfaces or near mov- ing parts like the steering wheel as it may prevent proper operation of the vehicle.
Page 3 7 Pin Input/Output Wiring Harness Part # 1124315 1 WHITE/BLACK (+) Siren Output 2 ORANGE (-) Starter Inhibit Relay Output 3 DARK BLUE Channel 3 Trunk Output (-) 250mA 4 PURPLE (+) Positive Door Trigger Input 5 BROWN (-) Negative Door Trigger Input 6 DK.
Page 4 INSTALLATION OF MAJOR COMPONENTS: Control Module: P/N 1365441 Select a mounting location inside the passenger compartment (up behind the dash) and secure using two screws provided. The control module can also be secured in place using cable ties. CAUTION: Do not mount the control module in the engine compartment, as it is not waterproof. You should also avoid mounting the unit directly onto factory installed electronic components.
Page 5 WIRING THE SYSTEMS 7 PIN MAIN HARNESS: P/N # 1124315 1) WHITE w/ BLACK TRACE WIRE: POSITIVE OUTPUT TO SIREN Route this wire through a rubber grommet in the firewall to the siren location. Connect the white/black wire to the positive wire of the siren. Secure the black ground wire of the siren to chassis ground. 2) ORANGE WIRE: GROUND OUTPUT WHEN ARMED This wire is provided to control the starter cut relay.
Page 6 4 Pin Main Power Harness: P/N #1124314 WHITE WIRE: + 12 VDC PULSED PARKING LIGHT OUTPUT ( 15 A MAX ) This wire is provided to flash the vehicle’s parking lights. Connect the white wire to the positive side of one of the vehicle’s parking lights.
Page 7 3 Wire Positive Switched Door Locks In this application, you will need to invert the door lock & unlock outputs to a positive pulse with either relays or the DLVI voltage inverter as shown in the diagram below. Unlock Lock Factory Lock Relay From Vehicle Chassis Ground...
Page 8 Adjusting the Shock Sensor : The sensitivity of the sensor is adjusted by turning the adjustment knob located on the side of the module clockwise to increase and counterclockwise to decrease. Gently turn the adjustment knob fully counterclockwise. ( DO NOT over turn this screw. Maximum rotation for this adjustment is 270°...
Page 9 PROGRAMMING BANK 1 (TRANSMITTERS): 1) Turn the ignition key to the ON position. 2) Press and release the valet/programming switch 3 times (Siren Chirps). 3 Press the Lock Button of each transmitter you want programmed until you hear a chirp from the horn or siren. 4) Press and release the valet/programming switch 1 time to advance to channel 2, Unlock.
Page 10 NOTES Page 10 128-9346 10 of 12...
Page 11 NOTES Page 11 128-9346 11 of 12...
Page 12 Antenna Wire, Route As High As Possible And Away From Other Electronic Modules For Best Range Sensor Adjust APS122E Green Green = (-) Unlock Red = (-) Lock White Parking Light Output (+) Push-Button White/Red (+) Parking Light Input Valet/Programming Switch Black (Chassis Ground) Red (+) 12 VDC White/Black (+) Siren Output...

Prestige APS-122E Installation Manual

Quick Links

Table Of Contents:

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Prestige APS-122E

Summary of Contents for Prestige APS-122E

Page 2: Before You Begin

Table of Contents