Technical Data; Before Commissioning; Installation - Scheppach DP19Vario Translation Of Original Operating Manual

6. Technical Data

Nominal input voltage
Power rating
Motor speed
Output speed (infinitely
adjustable)
Drill chuck mount
Chuck
Dimensions of drill table
Angle adjustment
Drilling depth
Pillar diameter
Height
Weight
Laser class
Wavelength of laser
Laser output
Noise and vibration values
The noise levels have been determined in accord-
ance with EN 61029.
sound pressure level - no load L
sound pressure level - load L
uncertainty K
pA
sound power level - no load L
sound power level - load L
uncertainty K
WA
Wear hearing protection.
Excessive noise can result in a loss of hearing. Total
vibration values (vector sum of three directions) de-
termined according to EN 61029.
Vibration emission value ah = 1.7 m/s
K uncertainty = 1,5 m/s
2
The specified vibration value was established in ac-
cordance with a standardized testing method. It may
change according to how the electric equipment is
used and may exceed the specified value in excep-
tional circumstances.
The specified vibration value can be used to compare
the equipment with other electric power tools.
26 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
230-240V~ 50
Hz
550 W
1450 min
-1
440 - 2580 min
-1
B16
1 - 16 mm
198 x194 mm
45° - 0° - 45°
60 mm
60 mm
830 mm
27,5 kg
2
650mm
1mW
70.2
dB(A)
pA
73.5
dB(A)
pA
3 dB(A)
82.7
dB(A)
WA
86.3
dB(A)
WA
3 dB(A)
2
The specified vibration value can be used for initial
assessment of a harmful effect.

7. Before commissioning

• Open the packaging and carefully remove the de-
vice.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for trans-
port damage.
• If possible, store the packaging until the warranty
period has expired.
ATTENTION
The device and the packaging are not children's
toys! Do not let children play with plastic bags,
films or small parts! There is a danger of choking
or suffocating!

8. Installation

Column and machine foot, fig. 3
1. Set the machine foot (1) down on the ground or
the workbench.
2. Place the column (2) on the base plate so that the
holes on the column (2) align with the holes on the
base plate (1).
3. Screw the four hexagonal screws (17) to fasten
the column into the base plate and tighten them
using a hexagon spanner.
Removing the rack, Fig.4
In order to install your drill, you must first remove the
rack (D)
1. Use an Allen key (SW3) to remove the ring (E)
and pull this off the column (2).
Now pull the rack (D) out.
2.
Installing the drilling table holder, Fig. 5-/
Insert the rack (D) into the groove on the drilling
1.
table holder (4).
2. Align the rack (D) centrally in relation to the drill-
ing table holder (4).
When bringing the rack (D) together within the
3.
groove, ensure that the tooth meshing between
the rack and the drilling table holder (4) is cor-
rect.
4. Now place the drilling table holder (4) with the
rack (D) on the column (2) and guide the rack (D)
into the bottom rack guide on the column foot.
Use the ring (E) to secure the rack (D). Ensure
5.
that the rack guide on the ring (E) is pointing
downwards. Tighten the integrated Allen screw
to affix the ring (E).