Table of Contents
Advertisement
Quick Links
Prior to installation, thoroughly familiarize yourself with this Installation Manual. Observe all safety warnings. During
It is your responsibility to install the product safely and to educate the customer on its safe use.
These installation instructions cover the outdoor
installation of single package gas electric heating and
cooling units. See the Specification Sheet or Technical
Manual applicable to your model* for information
regarding accessories.
IOG-3008D
11/2016
INSTALLATION & OPERATING
INSTRUCTIONS for
A/GPG14 M SERIES W/R410A
SINGLE PACKAGE GAS-ELECTRIC
HEATING & COOLING UNIT
Affix this manual and Users Information Manual adjacent to the unit.
RECOGNIZE THIS SYMBOL AS A SAFETY PRECAUTION.
ATTENTION INSTALLING PERSONNEL
installation or repair, caution is to be observed.
Goodman Manufacturing Company, L.P.
5151 San Felipe, Suite 500, Houston, TX 77056
www.goodmanmfg.com - or - www.amana-hac.com
2014-2016 Goodman Manufacturing Company, L.P.
©
is a registered trademark of Maytag Corporation or its related companies and is used under license. All rights reserved.
This Forced Air Central Unit Design Complies With
Requirements Embodied in The American National
Standard / National Standard of Canada Shown Below.
ANSI Z21.47•CSA-2.3 Central Furnaces
*NOTE: Please contact your distributor or
our website for the applicable
Specification Sheet or Technical Manual
referred to in this manual.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Goodman Maytag Amana A/GPG14 M Series
Summary of Contents for Goodman Maytag Amana A/GPG14 M Series
- Page 1 IOG-3008D 5151 San Felipe, Suite 500, Houston, TX 77056 11/2016 www.goodmanmfg.com - or - www.amana-hac.com 2014-2016 Goodman Manufacturing Company, L.P. © is a registered trademark of Maytag Corporation or its related companies and is used under license. All rights reserved.
-
Page 2: Table Of Contents
Index Replacement Parts ....................................3 ..................................... 3 RDERING ARTS Safety Instructions ....................................3 Unit location ....................................... 4 : ....................................4 NSTALLATIONS : ................................4 ROUND EVEL NSTALLATIONS : ..................................5 OOFTOP NSTALLATIONS : ................................5 NSTALLATIONS General Information ....................................6 .................................. -
Page 3: Replacement Parts
Keep this literature in a safe place for future reference. WARNING O NOT CONNECT TO OR USE ANY DEVICE THAT IS NOT DESIGN CERTIFIED BY GOODMAN FOR USE WITH THIS UNIT. SERIOUS PROPERTY DAMAGE, PERSONAL INJURY, REDUCED UNIT PERFORMANCE AND/ HAZARDOUS CONDITIONS MAY RESULT FROM THE USE OF SUCH NON-APPROVED DEVICES. -
Page 4: Unit Location
RISQUE D'EMPOISONNEMENT AU MONOXYDE DE CARBONE Advertencia especial para la instalación de calentadores ó manejadoras de aire en áreas cerradas como estacionamientos ó cuartos de servicio. Cette ventilation est nécessaire pour éviter le danger d'intoxication Las emisiones de monóxido de carbono pueden circular a través au CO pouvant survenir si un appareil produisant du monoxyde del aparato cuando se opera en cualquier modo. -
Page 5: Rooftop Installations Only
NSTALLATIONS • Sufficient structural support must be determined prior to locating and mounting the curb and package unit. • Ductwork must be constructed using industry guidelines. The duct work must be placed into the roof curb before mounting the package unit. •... -
Page 6: General Information
Refer to the Roof Curb Installation Instructions for proper curb in- for packaged and light commercial models. Specification sheets stallation. Curbing must be installed in compliance with the National can be found at www.goodmanmfg.com for Goodman ® brand prod- Roofing Contractors Association Manual. -
Page 7: High Altitude Derate (U.s. Installations Only )
5. Use two pipe wrenches when making connection to the Inlet Gas Pressure gas valve to keep it from turning. Natural Min. 5.0" W.C., Max. 10.0" W.C. 6. Install a manual shut-off valve in a convenient location Propane Min. 11.0" W.C., Max. 13.0" W.C. (within six feet of unit) between the meter and the unit. -
Page 8: Gas Piping Checks
IPING HECKS ANKS AND IPING Complete information regarding tank sizing for vaporization, recommended regulator settings and pipe sizing is available CAUTION from most regulator manufacturers and propane gas suppliers. Since propane gas will quickly dissolve white lead or most O PREVENT PROPERTY DAMAGE OR PERSONAL INJURY DUE TO FIRE, THE standard commercial compounds, special pipe dope must be FOLLOWING INSTRUCTIONS MUST BE PERFORMED REGARDING GAS used. -
Page 9: Electrical Wiring
Thermostat Wiring - Two Stage Models WARNING O PREVENT PROPERTY DAMAGE OR SERIOUS PERSONAL INJURY DUE TO FIRE OR EXPLOSION CAUSED BY A PROPANE GAS LEAK, INSTALL A GAS Thermostat DETECTING WARNING DEVICE. Two-Stage Heating with F THE PROPANE GAS UNIT IS INSTALLED IN AN EXCAVATED AREA OR A Two-Stage Cooling CONFINED SPACE, A WARNING DEVICE IS REQUIRED DUE TO: •... -
Page 10: Unit Voltage
If needed, these kits may be ordered through wiring from the unit control panel to the thermostat requires Goodman’s Service Parts department. coded cable. See below for ground level and rooftop wiring. For 3-phase models only, remove supply and return duct covers which are attached to the unit as shown below. -
Page 11: Ductwork
VENTING UCTWORK Duct systems and register sizes must be properly designed NOTE: Venting is self-contained. Do not modify or block. for the C.F.M. and external static pressure rating of the unit. Ductwork should be designed in accordance with the NSTALLATION recommended methods of Air Conditioning Contractors of America Manual D (Residential) or Manual Q (Commercial). -
Page 12: Normal Sequences Of Operation
2. Approximately seven seconds later, the indoor fan starts. NORMAL SEQUENCES OF OPERATION 3. The unit will deliver cooling to the conditioned space until the thermostat is satisfied. EATING 4. The compressor and outdoor fan will be de-energized This unit is equipped with an ignition control that automatically when the thermostat opens. - Page 13 6. Move the gas control valve switch to the OFF position. Do WARNING not force. 7. Wait five minutes to clear out any gas. O AVOID PROPERTY DAMAGE, PERSONAL INJURY OR DEATH DUE TO FIRE 8. Smell for gas, including near the ground. This is important OR EXPLOSION, A QUALIFIED SERVICER MUST INVESTIGATE THE REASON FOR because some types of gas are heavier than air.
-
Page 14: Gas Supply Pressure Measurement
Gas Supply And Manifold Check High Fire Regulator Adjust Outlet Regulator Gas supply pressure and manifold pressure with the burners Pressure Boss Vent operating must be as specified on the rating plate. UPPLY RESSURE EASUREMENT CAUTION O PREVENT UNRELIABLE OPERATION OR EQUIPMENT DAMAGE Low Fire Regulator Adjust NLET GAS SUPPLY PRESSURE MUST BE AS SPECIFIED ON THE UNIT... -
Page 15: Gas Manifold Pressure Measurement And Adjustment
12. Retest for leaks. If bubbles form, SHUT DOWN GAS AND Remove regulator cover screw from the outlet pressure REPAIR LEAKS IMMEDIATELY. regulator and turn screw clockwise to increase pressure or counterclockwise to decrease pressure. Replace 13. Turn ON electrical power and gas supply to the system. regulator cover screw. - Page 16 Main Burner Flame Check Limit Check Flames should be stable, soft and blue (dust may cause Check limit control operation after 15 minutes of operation orange tips but they must not be yellow) and extending directly by blocking the return air grille(s). outward from the burner without curling, floating or lifting off.
-
Page 17: Cooling Startup
OOLING TARTUP Design superheat & subcooling @ 95 °F outdoor ambient temperature NOTE: Check all manual reset limit controls in heating circuit if cooling mode does not operate. Models # Superheat ± 2°F Subcooling ± 3°F Compressor Protection Devices *PG1424***M The compressor includes components which are designed *PG1430***M to protect the compressor against abnormal operating... - Page 18 cycle is completed, and ignition is reattempted. The control Open Thermal Protection Device will repeat this routine three times if a measurable combustion If the primary limit switch opens, the gas valve is immediately is not established. The control will then shut off the induced de-energized, the induced draft and air circulating blowers draft blower and go into a lockout state.
-
Page 19: Abnormal Operation - Cooling
BNORMAL PERATION OOLING ABINET INISH AINTENANCE Use a fine grade automotive wax on the cabinet finish to Short Cycle Compressor Delay maintain the finish’s original high luster. This is especially The automatic ignition control has a built-in feature that important in installations with extended periods of direct prevents damage to the compressor in short cycling sunlight. -
Page 20: Main Burner Flame (Qualified Servicer Only )
6. To reduce the chances of repeated fouling of the heat 5. Replace burners and manifold, inspect the burner exchanger, perform the steps listed in “Startup, assembly for proper seating of burners in retention slots. Adjustments, and Checks”. 6. Reconnect electrical power and gas supply. URNER LAME UALIFIED... - Page 21 BLOWER PERFORMANCE DATA - SINGLE PHASE *PG1424040M41** - Rise Range: 25° - 55° T4 COOLING T5 COOLING T1 HEATING SPEED T2 HEATING SPEED T3 HEATING SPEED E.S.P. SPEED SPEED WATTS RISE WATTS RISE WATTS RISE WATTS WATTS 1,050 1,095 1,010 1,060 1,025 *PG1424060M41** - Rise Range: 30°...
- Page 22 BLOWER PERFORMANCE DATA - SINGLE PHASE *PG1436040M41** - Rise Range: 25° - 55° T4 COOLING T5 COOLING T1 HEATING SPEED T2 HEATING SPEED T3 HEATING SPEED E.S.P. SPEED SPEED WATTS RISE WATTS RISE WATTS RISE WATTS WATTS 1,115 1,265 1,305 1,440 1,075 1,230...
- Page 23 BLOWER PERFORMANCE DATA - SINGLE PHASE *PG1448060M41** - Rise Range: 30° - 60° T4 COOLING T5 COOLING T1 HEATING SPEED T2 HEATING SPEED T3 HEATING SPEED E.S.P. SPEED SPEED WATTS RISE WATTS RISE WATTS RISE WATTS WATTS 1,055 1,380 1,415 1,570 1,780 1,000...
- Page 24 BLOWER PERFORMANCE DATA - SINGLE PHASE *PG1461080M41** - Rise Range: 30° - 60° T1 LOW STAGE HEATING T2 HIGH STAGE HEATING T3 LOW STAGE T4 HIGH STAGE T5 COOLING SPEED SPEED HEATING SPEED COOLING SPEED SPEED E.S.P. WATTS RISE WATTS RISE WATTS WATTS...
- Page 25 IGNITION CONTROL DIAGNOSTIC INDICATOR CHART (SINGLE STAGE MODELS ONLY) Light Signal Refer to Abnormal Heating or Cooling Operation Sections of this Manual Internal Control Failure 1 Flash External Lockout 2 Flashes Pressure Switch Stuck Open 3 Flashes Pressure Switch Stuck Closed 4 Flashes Thermal Protection Device Open 5 Flashes...
- Page 26 IGNITION CONTROL DIAGNOSTIC INDICATOR CHART (TWO-STAGE MODELS ONLY) Red Light Signal Refer to Abnormal Heating or Cooling Operation Sections of this Manual Internal Control Failure 1 Flash External Lockout 2 Flashes Pressure Switch Stuck Open 3 Flashes Pressure Switch Stuck Closed 4 Flashes Thermal Protection Device Open 5 Flashes...
-
Page 27: Appendix
APPENDIX UNIT DIMENSIONS FLUE EXHAUST HOOD FLUE EXHAUST HEAT EXCHANGE ACCESS PANEL POWER WIRE ENTRANCE CONTROL WIRE ENTRANCE EXHAUST FLUE HOOD BLOWER ACCESS PANEL... -
Page 28: Wiring Diagrams
*PG14(24, 30, 36, 42)***M41* * WIRING DIAGRAM HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring. - Page 29 *PG14(24, 30, 36, 42)***M41* * WIRING DIAGRAM HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring.
- Page 30 PG1448***M41* * WIRING DIAGRAM HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. COMP CH OPTIONAL CONNECTED AT L1, L2 CH OPTIONAL NOTE 3 SEE NOTE 3...
- Page 31 *PG1448***M41* * WIRING DIAGRAM HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. COMPONENT LEGEND SUPPLY VOLTAGE A UXILLARY LIMIT SW ITCH 208-230/1/60 COMP COMPRESSOR...
- Page 32 *PG1461***M41** WIRING DIAGRAM HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. SEE NOTE6 SEE NOTE 3 COMP POWER SUPPLY BL BK 208-230/1/60 SEE NOTE 3...
- Page 33 *PG1461***M41** WIRING DIAGRAM HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. COMPONENT LEGEND FACTORY WIRING AUXILLARY LIMIT SWITCH LINE VO LTAGE SUPPLY VOLTAGE COMP COMPRESSOR...
-
Page 34: Minimum Clearances
MINIMUM CLEARANCES 48" MIN 12" MIN 3" 12" MIN 36" MIN (FOR SERVICE) NOTE: Roof overhang should be no more than 36". UNIT 2 Ton 2 1/2 Ton 3 Ton 3 1/2 / 4 Ton 5 Ton Min. Filter Size (1)20 x 20 x 1 (1)20 x 25 x 1 (1)25 x 25 x1 (2)20 x 20 x 1 (2)20 x 25 x 1 RECOMMENDED FILTER SIZES... - Page 35 PACKAGE UNITS - DUAL FUEL & GAS HOMEOWNER’S ROUTINE MAINTENANCE RECOMMENDATIONS We strongly recommend a bi-annual maintenance checkup be performed by a qualified service agency before the heating and cooling seasons begin. NNUAL NSPECTION UALIFIED ERVICER Your package unit should be inspected by a qualified installer, or service agency at least twice every year.
- Page 36 Check filters and replace if necessary. Verify the installation of the thermostat. 9 /2 0 1 4 is a registered trademark of Maytag Corporation or its related companies and is used under license to Goodman Company, L.P., Houston, TX, USA. All rights reserved.
- Page 37 Start-up Checklist Air Conditioning & Heating Start-Up (Insert the values as each item is completed.) ELECTRICAL Supply Voltage L1 - L2 L2 - L3 L3 - L1 Circuit 1 Compressor Amps Circuit 2 Compressor Amps Blower Amps Condenser Fan Amps Fan 1 Fan 2 Fan 3...
- Page 38 THIS PAGE LEFT INTENTIONALLY BLANK...
- Page 39 THIS PAGE LEFT INTENTIONALLY BLANK...
- Page 40 Goodman Manufacturing Company, L.P. 5151 San Felipe, Suite 500, Houston, TX 77056 www.goodmanmfg.com - or - www.amana-hac.com 2014-2016 Goodman Manufacturing Company, L.P. © is a registered trademark of Maytag Corporation or its related companies and is used under license. All rights reserved.
Need help?
Do you have a question about the Maytag Amana A/GPG14 M Series and is the answer not in the manual?
Questions and answers