Table of Contents
Advertisement
Quick Links
Link Power LPS3400-T1 Series
Outdoor Industrial 4-Port Managed
PoE Network Switch with 2 SFP
Uplink Ports
USER MANUAL
Inscape Data Corporation
1620 Oakland Road, STE D101
San Jose, CA 95131
U.S.A.
© Copyright 2016, Inscape Data Corporation, All Rights Reserved. LinkPower, AirEther, AirGoogle,
and Inscape Data are trademarks of Inscape Data Corporation
Disclaimer: While every effort is made to ensure the information given is accurate, Inscape Data
Corporation does not accept liability for any errors or mistakes which may arise. All information and
specifications are subject to change without notice.
Page | 1
Advertisement
Table of Contents
Related Manuals for Inscape Data Link Power LPS3400-T1 Series
Summary of Contents for Inscape Data Link Power LPS3400-T1 Series
- Page 1 Inscape Data are trademarks of Inscape Data Corporation Disclaimer: While every effort is made to ensure the information given is accurate, Inscape Data Corporation does not accept liability for any errors or mistakes which may arise. All information and specifications are subject to change without notice.
- Page 2 Certification Inscape Data Corporation certifies that this product met its published specifications at time of shipment from the factory. FCC Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
- Page 3 Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety standards of design, manufacture, and intended use of the instrument. Inscape Data Corporation assumes no liability for the customer’s failure to comply with these requirements.
- Page 4 Chassis Power Connection Before connecting or disconnecting ground or power wires to the chassis, ensure that power is removed from the device. To ensure that all power is OFF, locate the circuit breaker on the panel board that services the device, switch the circuit breaker to the OFF position, and tape the switch handle of the circuit breaker in the OFF position.
-
Page 5: Table Of Contents
Waterproof Ethernet, Fiber Optics, & Power Connector Assembly Diagram ............. 12 Optional Accessories ..............................12 Product Dimensions: ..............................13 Wall Mount & Pole Mount : ............................13 Product Specifications: ..............................14 Contacting Inscape Data Sales and Support Offices ....................15 Page | 5... -
Page 6: Packing List (In The Box)
Packing List (In The Box) Each package includes the following items: • LPS3400AFM-T1 or LPS3400ATM-T1 (1) • WM0001 Wall Mounting Kit (1) • MMK0001-L Pole Mount Kit (Optional Accessory) PART #: MMK0001-L To order online, https://www.inscapedata.com/store • Top Cover Screws & Hole Fillers (4) •... -
Page 7: Product Description
Product Description LPS3400-T1 Series Outdoor Industrial PoE Switch features with four PoE Ethernet ports and comply to 10/100/1000BaseT(X), IEEE802.3af/at PoE and two Gigabit SFP fiber optics uplink interfaces. Each of the PoE ports supplies DC power up to 15.4W for 802.3af and 30W for 802.3at, PoE Plus. The transfer data is up to 120Km from SFP fiber port to a control center. -
Page 8: Top Cover
Top Cover To connect the wires, you are simply to open the top cover by the latch. To install and connect the wire, please follow the connector assembly diagram on the next page. Please note the following IP weatherproof rating, when close the top cover: 1. -
Page 9: Led Indicator Description Table
LED Indicator Description Table: Description Indicator Status Green LED ON Power On, Normal SYS Indicator: POWER LED OFF Power OFF No Connected PD or Power OFF Yellow LED Blink Data transmission properly 1000M Indicator: Link Yellow LED ON Connected with 1000Mbps network device No connected PD Connected PD Device, working properly Green LED ON... -
Page 10: Power Redundancy & Ups Input
Wire Color Coding for Three-Screw Fixing Wire Terminal Coupler AC Power Cable: DC Power Cable: White (W) – AC/L 1. White (W) – Positive Green (G) – Ground 2. Green (G) – Ground 3. Black (B) – AC/N 3. Black (B) – Negative 4-Terminal DC Connector Set 3-Terminal AC Connector Set Figure 5 GREEN COLOR WIRE of Both AC/DC Power Cords Is Used for Grounding... -
Page 11: Reset Switch (System Reset)
RESET Switch (System Reset): There are two ways to reset the system, i.e., software reset and hardware reset, described as follow: Login to the Switch via 1. Software Reset: WEB management equipment, IP management by default IP Address: 192.168.2.1 click ''Maintenance Default login User Name: “admin”... -
Page 12: Connector Layout Diagram
Connector Layout Diagram: Support Cable Gland and Conduit Connectors The Hole Size: 1 Inch Diameter Waterproof Ethernet, Fiber Optics, & Power Connector Assembly Diagram Open Cut for Cable Insert Connector Assembly Diagram Plastic Plug Note: The Sealing Insert comes with one and three holes. The Plastic Plug MUST be used to cover the Sealing Insert, if any of the hole is not used in order to maintain waterproof of the connector. -
Page 13: Product Dimensions
DPCK0001 DC Power Cord Kit Product Dimensions: Wall Mount & Pole Mount : Page | 13... -
Page 14: Product Specifications
Product Specifications: ELECTRICAL PIN OUT DIAGRAM Page | 14... -
Page 15: Contacting Inscape Data Sales And Support Offices
Contacting Inscape Data Sales and Support Offices For more information about Inscape Data Corporation products, applications, support, and for a current sales office listing, visit our web site: http://www.inscapedata.com U.S. Headquarters Here’s how to reach us if you’d like to place an order or if you have questions, concerns, or need support...
Need help?
Do you have a question about the Link Power LPS3400-T1 Series and is the answer not in the manual?
Questions and answers