1. Manuals
  2. Brands
  3. AZZA Manuals
  4. Motherboard
  5. 6IFB
  6. Operation manual

AZZA 6IFB Operation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
PT-6IFB
SYSTEM BOARD
( VER. 2.x )
OPERATION MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 6IFB and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for AZZA 6IFB

Summary of Contents for AZZA 6IFB

  • Page 1 PT-6IFB SYSTEM BOARD ( VER. 2.x ) OPERATION MANUAL...

  • Page 2: Table Of Contents

    1.1 SYSTEM OVERVIEW ................. 1 1.2 FEATURES....................1 2 SPECIFICATIONS ....................1 3 SYSTEM BOARD LAYOUT ................1 3.1 PT-6IFB VER. 2.x..................1 4 HARDWARE SETUP ..................1 4.1 UNPACKING ....................1 4.2 HARDWARE CONFIGURATION............1 4.2.1 DRAM INSTALLATION..............1 4.2.2 CONNECTORS..................
  • Page 3 PT-6IFB SYSTEM BOARD TRADEMARKS All trademarks used in this manual are the property of their respective owners. NOTE The "LOAD SETUP DEFAULTS" function loads the default settings directly from BIOS default table, these default settings are the best-case values that should optimize system performance and increase system stability .
  • Page 4 Printed in Taiwan Date : May/31/1997...

  • Page 5: Introduction

    INTRODUCTION SYSTEM OVERVIEW The PT-6IFB Pentium II PCI Local Bus system board is an ATX form-factor system board. It is designed based on the Intel 82440FX PCIset system chipset and Winbond I/O chipset. It built-in two channel PIO and Bus Master Enhanced PCI IDE ports, one Floppy Disk control port, two high speed Serial ports (UARTs) and one multimode Parallel port and also supports PS/2 mouse, IR and USB ports.
  • Page 6 PT-6IFB INTRODUCTION SYSTEM BOARD Cache Memory : Supports Pentium II CPU's built-in 256KB/512KB L2 cache. System BIOS : Supports Plug and Play System BIOS. IDE ports : Supports two channel PIO and Bus Master Enhanced PCI IDE ports, up to Mode 4 timing, and up to 22 MBytes/s transfer rates.

  • Page 7: Specifications

    PT-6IFB SPECIFICATIONS SYSTEM BOARD SPECIFICATIONS Intel Pentium II (S.E.C. Cartridge) processor 233 MHz, 266 MHz and maybe upon. CPU VCC Voltage Regulator circuits on board, supports +1.80V DC through +2.80V DC CPU Core Voltage. WORD SIZE Data Path : 8-bit, 16-bit, 32-bit, 64-bit...
  • Page 8 PT-6IFB SPECIFICATIONS SYSTEM BOARD IDE PORTS Two channel PIO and Bus Master Enhanced PCI IDE ports, maximum could be connected up to 4 IDE Hard Disk and ATAPI CD-ROM device. BIOS supports IDE CD-ROM boot-up. SUPER I/O PORTS 1. Two high speed NS16C550 compatible serial ports (UARTs).

  • Page 9: System Board Layout

    PT-6IFB HARDWARE SETUP SYSTEM BOARD SYSTEM BOARD LAYOUT PT-6IFB VER. 2.x Explanation : All connectors, jumpers and components which marks by a black point on the corner means the pin-1 side of the connector, jumper and component. SYS. BIOS CN14...

  • Page 10: Hardware Setup

    Before the system board is ready to operate, the hardware must be configured to allow for various functions within the system. To configure the PT-6IFB system board is a simple task, only a few jumpers, connectors, cables and sockets needs to be selected and installed.
  • Page 11 PT-6IFB SPECIFICATIONS SYSTEM BOARD There is no jumper needed for DRAM configuration, DRAMs' type and size will be detected by system BIOS automatically. In DRAM memory subsystem, ECC and Parity can be checked on the DRAM interface (Functions selected by BIOS via CMOS setup, please refer to Chapter 5, the default status is parity selected.) All SIMMs must be populated with true parity bit to...

  • Page 12: Connectors

    PT-6IFB SPECIFICATIONS SYSTEM BOARD CONNECTORS A connector is two or more pins those are used make connections to the system standard accessories (such as power, mouse, printer,...etc.) The following is a list of connectors on board and as well as descriptions of each individual connector.
  • Page 13 PT-6IFB SPECIFICATIONS SYSTEM BOARD (D) CN3 Power connector 11 1 Pin # Assignment Pin # Assignment + 3.3V DC + 3.3V DC + 3.3V DC 12V DC Ground Ground PS-ON + 5V DC Ground Ground Ground + 5V DC Ground...
  • Page 14 PT-6IFB SPECIFICATIONS SYSTEM BOARD (F) CN5 Parallel Port connector (Supports SPP/EPP/ECP mode, selected by BIOS setup,using IRQ7 or IRQ5,ECP using DMA channel 3 or 1) 1 14 Pin # Assignment Pin # Assignment STROBE AUTO FEED Data Bit 0 ERROR...
  • Page 15 PT-6IFB SPECIFICATIONS SYSTEM BOARD (J) CN9 IDE 2 connector (Primary IDE Port, I/O address is 1F0H, using IRQ14) (K) CN10 IDE 1 connector (Secondary IDE Port, I/O address is 170H, using MIRQ0) (L) CN11 IR (Infrared Rays) connector Pin # Assignment...
  • Page 16 PT-6IFB SPECIFICATIONS SYSTEM BOARD (O) CN14 USB 2 (Universal Serial Bus port2) connector Pin # Assignment + 5V DC DATA DATA Ground (P) RS Reset Button connector Pin # Assignment Pin1&2 Function Ground Open No action Reset Control Short System Reset...
  • Page 17 PT-6IFB SPECIFICATIONS SYSTEM BOARD (U) SPEAKER Speaker connector Pin # Assignment + 5V DC No Connection No Connection Speaker Data Signal No Connection (V) KEY LOCK Front Panel Power LED & Key-Lock connector Pin # Assignment Pullup (+ 5V DC for Power LED)

  • Page 18: Jumpers

    PT-6IFB SPECIFICATIONS SYSTEM BOARD JUMPERS A jumper is two, three or more pins which may or may not be covered by a plastic connector plug (mini-jumper). A jumper is used for selecting different system options. Please make sure all jumpers at correct position before this system board used.

  • Page 19: Award Bios Setup

    PT-6IFB AWARD BIOS SETUP SYSTEM BOARD AWARD BIOS SETUP GETTING STARTED When the system is first powered on or reset, the BIOS will enter the Power-On Self Test routines ( POST : Display a copyright message on the screen followed by a diagnostics and initialization procedure.) (If an EGA or VGA card is installed, the...

  • Page 20: Control Keys

    PT-6IFB AWARD BIOS SETUP SYSTEM BOARD ESC : Quit : Select Item F10 : Save & Exit Setup (Shift)F2 : Change Color Time, Date, Hard Disk Type ... Fig. 5-2 CMOS SETUP MAIN MENU screen. CONTROL KEYS Listed below is an explanation of the keys displayed at the bottom of the screens...

  • Page 21: Bios Features Setup

    PT-6IFB AWARD BIOS SETUP SYSTEM BOARD HARD DISKS TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE Primary Master Auto Auto Primary Slave None ------ Secondary Master Auto Auto Secondary Slave None ------ Drive A : 1.44M, 3.5 in. Drive B : None...
  • Page 22 PT-6IFB AWARD BIOS SETUP SYSTEM BOARD Swap Floppy Drive : Disabled D8000-DBFFF Shadow : Disabled Boot Up Floppy Seek : Enabled DC000-DFFFF Shadow : Disabled Boot Up NumLock Status : On Boot Up System Speed : High Gate A20 Option...

  • Page 23: Chipset Features Setup

    PT-6IFB AWARD BIOS SETUP SYSTEM BOARD Some display cards that are non-standard VGA such as graphics accelerators or MPEG Video Cards may not show color properly. The setting Enabled should correct this problem. Otherwise leave this on the setup default setting of Disabled.
  • Page 24 PT-6IFB AWARD BIOS SETUP SYSTEM BOARD Read-Around-Write : Enabled PCI Burst Write Combine : Enabled PCI-To-DRAM Pipeline : Enabled ESC : Quit : Select Item CPU-To-PCI Write Post : Enabled : Help PU/PD/+/- : Modify CPU-To-PCI IDE Posting : Enabled...

  • Page 25: Power Management Setup

    PT-6IFB AWARD BIOS SETUP SYSTEM BOARD PCI-To-DRAM Pipeline : The default setting of Enabled will increase the bandwidth of the path between the PCI and the DRAM to enhance the PCI bus efficiency and DRAM accessing. CPU-To-PCI Write Post : The default setting of Enabled will increase the efficiency of the PCI bus and speed up the execution in the processor.

  • Page 26: Pnp/Pci Configuration

    PT-6IFB AWARD BIOS SETUP SYSTEM BOARD IRQ3 (Wake-Up Event) : ON IRQ 13 (Coprocessor) : ON IRQ4 (Wake-Up Event) : ON IRQ 14 (Hard Disk) : ON IRQ8 (Wake-Up Event) : OFF IRQ 15 (Reserved) : OFF IRQ12 (Wake-Up Event) : ON...
  • Page 27 PT-6IFB AWARD BIOS SETUP SYSTEM BOARD DMA-3 assigned to : PCI/ISA PnP ESC : Quit : Select Item DMA-5 assigned to : PCI/ISA PnP : Help PU/PD/+/- : Modify DMA-6 assigned to : PCI/ISA PnP : Old Values (Shift)F2 : Color...

  • Page 28: Integrated Peripherals

    PT-6IFB AWARD BIOS SETUP SYSTEM BOARD PCI-AUTO : The BIOS will scan for PCI IDE devices and determine the location of PCI IDE device, then assign IRQ 14 for primary IDE INT#, and assign IRQ 15 for secondary IDE INT#.

  • Page 29: Load Setup Defaults

    PT-6IFB AWARD BIOS SETUP SYSTEM BOARD Onboard Serial Port 1 : 3F8/IRQ4 Onboard Serial Port 2 : 2F8/IRQ3 Onboard IR Controller : Disabled ESC : Quit : Select Item : Help PU/PD/+/- : Modify : Old Values (Shift)F2 : Color : Load Setup Defaults Fig.

  • Page 30: Supervisor Password / User Password

    PT-6IFB AWARD BIOS SETUP SYSTEM BOARD stability. If CMOS RAM is corrupted, the SETUP DEFAULTS settings are loaded automatically. SUPERVISOR PASSWORD / USER PASSWORD Type the Password and press "Enter", then repeat. Enters up to eight alphanumeric characters. By pressing "Enter" key twice, without any alphanumeric character enters, the PASSWORD will be disabled.
  • Page 31 PT-6IFB AWARD BIOS SETUP SYSTEM BOARD...

  • Page 32: Installing And Removing The Processor

    PT-6IFB SYSTEM BOARD Installing and Removing the Processor Installing the Boxed Processor Mount the two black plastic pegs onto the motherboard. These pegs will be used attach the fan heatsink supports. Notice that one hole and the base of one peg are larger than the other hole and peg base.
  • Page 33 PT-6IFB AWARD BIOS SETUP SYSTEM BOARD Slide the clip (A) on each support toward the processor, exposing the hole that will fit over the peg on the motherboard. Push the latches (B) on the processor toward the center of the processor until they click into place.

  • Page 34: Removing The Processor

    PT-6IFB AWARD BIOS SETUP SYSTEM BOARD Attach the small end of the power cable (F) to the three-pin connector on the processor, then attach the large end to the three-pin connector on the motherboard. Consult the motherboard documentation to find the connector.
  • Page 35 PT-6IFB AWARD BIOS SETUP SYSTEM BOARD WARRING ! When handling the processor, avoid placing direct pressure on the label area of the fan. When removing the processor, avoid pressing down on the motherboard or components. Instead, press down on plastic connectors.

This manual is also suitable for:

Pt-6ifb

Table of Contents