Related Manuals for jcb 21-DH1700
Summary of Contents for jcb 21-DH1700
- Page 1 POWER TOOL INSTRUCTION & USER MANUAL 21-DH1700 Original Instructions IM-DH1700-EN Iss: 06/2021...
- Page 2 The month and year of manufacture can be found within the product serial number e.g. MMYYPPPAXXXXX. Where production month (MM) and production year (YY) are included. 21-DH1700 Designation of the tool (DH - Demolition Hammer, 1700 - 1700W power) 21-DH1700...
-
Page 3: Table Of Contents
Electrical Safety COMPONENT LIST TECHNICAL DATA NOISE INFORMATION VIBRATION INFORMATION OPERATING INSTRUCTIONS Intended Use Changing the Tool Initial Operation Switching On and Off Maintenance Transport and Storage WARRANTY STATEMENT Terms and Conditions EU/UK DECLARATION OF CONFORMITY 21-DH1700 Instruction & User Manual... -
Page 4: General Power Tool Safety Warnings
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. 21-DH1700 Instruction & User Manual... -
Page 5: Power Tool Use And Care
Such preventive safety measures reduce the risk of starting the power tool accidentally. 21-DH1700 Instruction & User Manual... -
Page 6: Tool Specific Safety Warnings
Keep the power cord away from the bit. Do not wrap the cord around any point of your body. An electric cord damaged by a chisel bit may cause personal injury and loss of control. 21-DH1700 Instruction & User Manual... -
Page 7: Electrical Safety
10% lower operating voltage (or incorrect mains Hz frequency) can cause loss of power and overheating. All JCB tools are factory tested. If this tool does not operate check the power supply. Make sure your power supply agrees with the voltage specified on the product rating label. -
Page 8: Component List
COMPONENT LIST Fig. 1 30MM HEX CHUCK ON/OFF TRIGGER LOCK-ON BUTTON AUXILIARY HANDLE OIL CAP POWER CABLE 6a/6b. ANTIVIBRATION CONTROL DEVICE Fig. 2 Fig. 3 Fig. 4 21-DH1700 Instruction & User Manual... -
Page 9: Technical Data
(taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time). 21-DH1700 Instruction & User Manual... -
Page 10: Vibration Information
Avoid using tools in temperatures of 10 ° exposure. or less. Plan your work schedule to spread any high THIS TOOL MAY CAUSE HAND-ARM vibration tool use across a number of days. VIBRATION SYNDROME IF USAGE IS NOT ADEQUATELY MANAGED. 21-DH1700 Instruction & User Manual... -
Page 11: Operating Instructions
Inserting (see Fig. 2) Clean tool bits and grease with a thin layer of machine grease before fitting. Insert the chisel into the chuck and push it in as far as possible. 21-DH1700 Instruction & User Manual... -
Page 12: Switching On And Off
Never try to repair the tool yourself. Release pressure on the ON/OFF trigger. Take to an authorised service centre. The tool will come to a stop. If the carbon brushes require replacement, this must be performed by an authorised warranty agent. 21-DH1700 Instruction & User Manual... -
Page 13: Transport And Storage
Always carry the tool using the purpose- designed handle. Ensure that the tool is not at risk of tipping over or exposed to vibration and shocks during transport, especially if the tool will be transported by car or other vehicle. 21-DH1700 Instruction & User Manual... -
Page 14: Warranty Statement
Warranty cover commences from the date of purchase on the retail sales receipt and is valid only for JCB Tools products purchased within the UK bearing the CE and UKCA mark and a visible serial number. - Page 15 Repairs have not been undertaken using non-genuine spare parts. JCB Power Tools used for Hire Fleets or as part of B2B and Service Contracts are not covered by these terms and conditions. JCB Tools 3 Year Warranty excludes the following (where applicable): Components normally subject to wear such as carbon brushes.
-
Page 16: Eu/Uk Declaration Of Conformity
JCB-DH1700, 21-DH1700 DECLARATION: EU Product Code No. JCB-DH1700-E Factory Reference No. Z1G-DS-117H Name: Yellow and Black Tools Ltd. (T/A: JCB Tools) IDENTIFICATION DETAILS OF Unit 55 Romsey Industrial Estate, Greatbridge Road Address: MANUFACTURER: Romsey, Hampshire SO51 0HR Country: Authorised Representative Service...
Need help?
Do you have a question about the 21-DH1700 and is the answer not in the manual?
Questions and answers