Page 2
IMPORTANT! READ CAREFULLY BEFORE USE. KEEP THIS GUIDE FOR FUTURE REFERENCE. Screenshots and graphics in this book may differ slightly from what you see due to differences in your product firmware or your computer operating system. Every effort has been made to ensure that the information in this manual is accurate.
Document Conventions Warnings and Notes These are how warnings and notes are shown in this guide. Warnings tell you about things that could harm you or your device. Note: Notes tell you other important information (for example, other things you may need to configure or helpful tips) or recommendations.
Table of Contents Table of Contents Document Conventions ........................3 Contents Overview ..........................4 Table of Contents ..........................5 Part I: User’s Guide..................10 Chapter 1 Introduction ............................11 1.1 Overview ............................11 1.2 Dual-Band WiFi ..........................12 1.3 Daisy Chain ............................. 13 1.4 MPro Mesh ............................14 1.5 Ways to Manage the WX3401-B0 ....................
Page 6
Table of Contents 4.3 Setting Up Your WX3401-B0 ......................31 4.3.1 Scenario 1-Connect to a Zyxel MPro Mesh Router Wirelessly .......... 31 4.3.2 Scenario 2-Connect to a Non-MPro Mesh Router with an Ethernet Cable ....36 4.4 Use the MPro Mesh App to Manage Your Mesh Network ............43 4.4.1 Home Screen .........................
Page 7
Table of Contents 6.4.1 Add/Edit MAC Addresses ....................92 6.5 WPS Settings ............................ 92 6.6 WMM Settings ..........................94 6.7 Others Settings ..........................95 6.8 Channel Status Settings ......................... 97 6.9 Operating Modes Settings ......................98 6.10 AP List Screen ..........................100 6.11 Technical Reference ........................
Page 8
Table of Contents 11.1 System Overview ........................124 11.2 System Settings ..........................124 Chapter 12 User Account............................125 12.1 User Account Overview ......................125 12.2 User Account Settings ........................ 125 12.2.1 User Account Add/Edit ....................126 Chapter 13 Remote Management ........................128 13.1 Remote Management Overview .....................
Page 9
Table of Contents 18.1 Power, Hardware Connections, and LEDs ................143 18.2 WX3401-B0 Access and Login ....................144 18.3 Internet Access ........................... 145 18.4 Wireless Internet Access ......................146 18.5 IP Address Setup ......................... 147 18.6 Resetting the WX3401-B0 to Its Factory Defaults ..............150 18.7 MPro Mesh App Problems ......................
H A P T E R Introduction 1.1 Overview The WX3401-B0 can function as a Repeater or an Access Point (AP). Set your WX3401-B0 as an AP if you already have a router in your network and you want to bridge a wired network (LAN) and another LAN or wireless LAN (WLAN) in the same subnet.
Chapter 1 Introduction You can add more WX3401-B0s to your network to form a daisy chain, see Section 1.3 on page 13 more information. Set up a Mesh network with your WX3401-B0 to enjoy band steering, AP steering, auto-configuration and other advances for your wireless network, see Section 1.4 on page 14 for more information.
Chapter 1 Introduction Figure 4 Dual-Band Application The WX3401-B0 can act as an Access Point (AP) for IEEE 802.11a/b/g/n/ac/ax wireless clients, such as notebook computers, iPads, smartphones, and so on. It allows them to connect to the Internet without having to rely on Ethernet cables. Figure 5 Wireless Access Example 1.3 Daisy Chain You can add more extenders to your network to form a daisy chain.
Chapter 1 Introduction Figure 6 Scenario 1: three APs Figure 7 Scenario 2: two APs and one RP Figure 8 Scenario 3: one AP and two RPs Figure 9 Scenario 4: two RPs Note: Set up your network as in Sencario1-3 if your router does not support Zyxel MPro Mesh. Scenario 4 in Figure 9 is only for routers that support Zyxel MPro Mesh.
Page 15
Chapter 1 Introduction Figure 10 AP Steering Application • Band steering allows 2.4GHz/5GHz dual-band wireless clients to move from one band to another. For example, if the 2.4GHz channel is congested, wireless clients that support 5GHz can move to the 5GHz band.
Page 16
Chapter 1 Introduction Figure 11 Band Steering Application You need a router or an AP that can function as a controller in order to set up a Mesh network. A controller manages and coordinates WiFi activity in a network. A controller also manages the SSIDs and password on all APs in a network (auto-configuration). For example, if you change the SSID on a router, all the SSIDs of APs in a network will also change.
Chapter 1 Introduction • RP- Repeater • C1- Client1 • C2- Client2 • APC- Access Point coverage area • RPC- Repeater coverage area Note: Your router must have an Internet connection whether it supports MPro Mesh or not. Note: If your router supports Zyxel MPro Mesh, it will serve as the router controller in a Mesh network with the WX3401-B0.
Page 18
Chapter 1 Introduction Note: You modem/router must have an Internet connection. Connect your computer to the LAN port of the WX3401-B0. Give your computer a fixed IP address in the range between 192.168.1.3 and 192.168.1.254. After you have set your computer’s IP address, open a web browser such as Internet Explorer and enter “http://192.168.1.2”...
H A P T E R Hardware This section describes the front and back panel of the WX3401-B0. Refer to the Quick Start Guides to see how to make the hardware connections. 2.1 Front Panel and LEDs This figure shows the front panel of the WX3401-B0. Use the LEDs to determine if the WX3401-B0 is behaving normally or if there are problems on your network.
Chapter 2 Hardware 2.2 Rear Panel Figure 14 The WX3401-B0’s Rear Panel Table 1 Panel Ports and Buttons LABEL DESCRIPTION LAN1/LAN2 Connect computers or other Ethernet devices to Ethernet ports for Internet access. Press the WPS button once within eight seconds to enable the AP/Repeater mode. POWER ON/OFF Connect the power cable and then press the power button to start the device.
Page 21
Chapter 2 Hardware Figure 15 Screw Specifications Select a position free of obstructions on a wall strong enough to hold the weight of the device. Mark two holes on the wall at the appropriate distance apart for the screws. Be careful to avoid damaging pipes or cables located inside the wall when drilling holes for the screws.
Chapter 2 Hardware Figure 17 Wall Mounting Example 2.4 WPS Button Your WX3401-B0 supports WiFi Protected Setup (WPS), which is an easy way to set up a secure wireless network. WPS is an industry standard specification, defined by the Wi-Fi Alliance. WPS allows you to quickly set up a wireless network with strong security, without having to configure security settings manually.
Chapter 2 Hardware • Repeater mode (the WX3401-B0 to the wireless client) 1. Press the WX3401-B0 WPS button twice within 8 seconds to copy the WiFi settings from the WX3401- B0 to a wireless client, such as your smartphone or laptop. 2.
H A P T E R The Web Configurator 3.1 Overview The Web Configurator is an HTML-based management interface that allows easy system setup and management via Internet browser. Use a browser that supports HTML5, such as Microsoft Edge, Internet Explorer 11, Mozilla Firefox, or Google Chrome.
Page 25
Chapter 3 The Web Configurator Note: The default allowable times that you can enter the Password is 3. If you entered the wrong password for the fourth time, by default the Web Configurator will lock itself for 5 minutes before you can try entering the correct Password again. You can change these settings at Maintenance >...
Page 26
Chapter 3 The Web Configurator Figure 20 Connection Status WX3401-B0 User’s Guide...
Chapter 3 The Web Configurator 3.2 Web Configurator Layout Figure 21 Screen Layout As illustrated above, the main screen is divided into these parts: • A - Navigation Panel • B - Layout Icon • C - Main Window 3.2.1 Navigation Panel Click the menu icon ( to display the navigation panel that contains configuration menus and icons (quick links).
Page 28
Chapter 3 The Web Configurator Figure 22 Navigation Panel 3.2.1.1 Configuration Menus Use the menu items on the navigation panel to open screens to configure WX3401-B0 features. The following tables describe each menu item. Table 3 Configuration Menus Summary LINK FUNCTION Connection Status Use this screen to configure basic Internet access and wireless settings.
Page 29
Chapter 3 The Web Configurator Table 3 Configuration Menus Summary (continued) LINK FUNCTION Wireless General Use this screen to configure the WiFi settings and wireless LAN authentication/security settings. The main 2.4G and/or 5G is enabled by default and not configurable. Guest/More AP Use this screen to configure multiple BSSs on the WX3401-B0.
Page 30
Chapter 3 The Web Configurator 3.2.1.2 Icons The navigation panel provides some icons on the right hand side. The icons provide the following functions. Table 4 Web Configurator Icons ICON DESCRIPTION Theme: Click this icon to select a color that you prefer and apply it to the Web Configurator. Restart: Click this icon to reboot the WX3401-B0 without turning the power off.
H A P T E R Tutorials 4.1 Overview This chapter provides tutorials for setting up the WX3401-B0 using a wireless or a wired connection. Besides the Web Configurator, this chapter shows you how to use the MPro Mesh app to manage the WX3401-B0 and its Mesh network.
Page 32
Chapter 4 Tutorials Connect your mobile device to the wireless network of the Zyxel MPro Mesh Router. Note the SSID and password on the back label of the Zyxel MPro Mesh Router. Find this SSID on your mobile device. Enter the key to connect to your router.
Page 33
Chapter 4 Tutorials Rotate the stand on the bottom of the WX3401-B0 90 degrees. Place the WX3401-B0 where you want to extend the coverage of your wireless network. Plug in the power cable and switch on the WX3401-B0. Wait until the POWER LED turns steady green. This may take up to 2.5 minutes.
Page 34
Chapter 4 Tutorials Select the Use WiFi scenario. Follow the instructions to start pairing the WX3401-B0 with a Zyxel MPro Mesh Router (with the DX5301-B as an example). Once the pairing starts, a 3-minute countdown timer will begin. Within 2 minutes, press the WPS button once on the WX3401-B0 until WiFi LED starts blinking slowly. WX3401-B0 User’s Guide...
Page 35
Chapter 4 Tutorials 10 After the WIFI LED turns steady green or fast blinking, wait for up to 2 minutes. The POWER LED should start blinking. The POWER and Link LED will turn solid green if the pairing process is successful. You can also check the result on the app screen.
Chapter 4 Tutorials Zyxel MPro Mesh router Table 5 LED Table (for the WX3401-B0) COLOR STATUS DESCRIPTION POWER Green Power is on or the MPro Mesh configuration process is done. Blinking The WX3401 is starting up or under the MPro Mesh configuration process.
Page 37
Chapter 4 Tutorials Rotate the stand on the bottom of the WX3401-1 90 degrees. Plug in the power cable and switch on the WX3401-1. Wait until the POWER LED turns steady green. This may take up to 2.5 minutes. On your mobile device, go to the WiFi settings. Long press your existing WiFi connection. Tap Forget network to remove your existing WiFi connection.
Page 38
Chapter 4 Tutorials Connect your mobile device to the wireless network of the WX3401-1. Note the SSID and key on the side label of the WX3401-1. Find this SSID on your mobile device. Enter the key to connect to your WX3401-1. Note: In this scenario, the is the wireless controller, so you must connect to it to use WX3401-1...
Page 39
Chapter 4 Tutorials Connect the MPro Mesh App to the WX3401-1. Open the app, enter the username and password on the side label of the WX3401-1 when prompted. Connect the WX3401-2 to the WX3401-1 Rotate the stand on the bottom of the WX3401-2 90 degrees. Rotate the stand Place the WX3401-2 where you want to extend the coverage of your network.
Page 40
Chapter 4 Tutorials Plug in the power cable and switch on the WX3401-2. Wait until the POWER LED turns steady green. This may take up to 2.5 minutes. Turn on the second WX3401-B0 When the POWER LED on the WX3401-2 is steady green, open the MPro Mesh App. On the Home screen, tap on the icon to add the WX3401-2.
Page 41
Chapter 4 Tutorials Paring Within 2 minutes, press the WPS button once on the WX3401-2 for less than 3 seconds. Press the WPS button on the second WX3401-B0 The POWER and Link LED on the WX3401-2 turns steady green if the pairing process is successful. You can also check the result on the app screen.
Page 42
Chapter 4 Tutorials Click Done to finish the pairing process. The the WX3401-1 (the controller) will undergo an auto - configuration after a Mesh network is established. (See Section 1.4 on page 14 for more information). Check the status of your wireless Mesh network on the Home screen. Successful pairing The POWER LED shows if the WX3401-2 is ready to join the WiFi network.
Chapter 4 Tutorials 10 Now you can connect your wireless clients to your wireless Mesh network. To do this, note the SSID and wireless key printed on the side label of the WX3401-1 using this SSID. Connect your other wireless clients to your wireless Mesh network 4.4 Use the MPro Mesh App to Manage Your Mesh Network You can manage your controller (the WX3401-1 or a Zyxel MPro Mesh Router) and their WiFi settings...
Chapter 4 Tutorials Home 4.4.2 Gateway Detail Screen Use this screen to view basic information of your controller (Zyxel MPro Mesh Router or the WX3401-1). Tap on the icon next to the model name WX3401-00016 to open the following screen. WX3401-B0 User’s Guide...
Page 45
Chapter 4 Tutorials Gateway Detail Tap on the icon to change the model name shown on the app. WX3401-B0 User’s Guide...
Page 46
Chapter 4 Tutorials Change model name Tap the icon to save the changes made. Tap on Reboot at the bottom left corner to restart your device. WX3401-B0 User’s Guide...
Chapter 4 Tutorials Reboot 4.4.3 Add Mesh Screen Use this screen to add extenders or APs to your network to form a daisy chain (for more information on daisy chain, see Section 1.3 on page 13). On the Home screen, tap on the icon to open the following screen.
Page 48
Chapter 4 Tutorials Select the Connection Method To add an extender to your network wirelessly: Tap on the icon under Use WiFi. The following screen appears. Follow the instruction to set your device to the Repeater mode. Then click Next to go to the next step. WX3401-B0 User’s Guide...
Page 49
Chapter 4 Tutorials Place WiFi Extender Note: You can tap on See Tips on the top right corner to see instruction for finding ideal places to set up your devices. Note: Your device may not have a mode switch. The method for setting modes for your device may vary depending on the device you use.
Page 50
Chapter 4 Tutorials The following screen appears. Wait for the WX3401-B0 to connect to the MPro Mesh Router through the WPS method. WX3401-B0 User’s Guide...
Page 51
Chapter 4 Tutorials Press the WPS button The following screen appears if the connection fails. Tap on Need help to see possible reasons for the connection failure or tap on Try Again to try connecting your devices through WPS button once more. WX3401-B0 User’s Guide...
Page 52
Chapter 4 Tutorials Unsuccessful connection The following screen appears if the WX3401-B0 is connected to the MPro Mesh Router successfully. WX3401-B0 User’s Guide...
Page 54
Chapter 4 Tutorials To add an extender to your network with an Ethernet cable: Tap on the icon under Use Ethernet Cable. The following screen shows. Follow the instruction to set your device to the AP mode. Then click Done to go back to the Home page.
Chapter 4 Tutorials 4.5 Devices Screen Use this screen to view clients that are connected to the WX3401-B0 and their link quality. You can tap on the search icon to search for a certain client. Tap on Devices in the navigation panel to open the following screen. WX3401-B0 User’s Guide...
Chapter 4 Tutorials Devices 4.5.1 Device Detail Screen Use this screen to view basic information of the client connected to the WX3401-B0 and block Internet access to it. Tap on the icon to open the following screen. WX3401-B0 User’s Guide...
Chapter 4 Tutorials Device Detail Tap on the icon to change the name of your device shown on the app. 4.6 WiFi Settings Screen Use this screen to configure settings for your wireless network. For more information on Guest WiFi, see Section 4.7 on page Tap on WiFi in the navigation panel to open the following screen.
Page 58
Chapter 4 Tutorials WiFi Settings Tap on the icon to show the QR code for connecting a WiFi client to the WX3401-B0. WX3401-B0 User’s Guide...
Page 59
Chapter 4 Tutorials QR Code for WiFi Connection Tap on the icon to open the following screen. Use this screen to edit the SSID (WiFi name) and password for your WiFi network. WX3401-B0 User’s Guide...
Chapter 4 Tutorials Edit WiFi Settings Tap on Save to save your changes, or tap on Cancel to go back to the previous screen. 4.7 Guest WiFi Settings Screen Use this screen to configure guest WiFi settings. Slide the Guest WiFi switch to the right to enable guest WiFi.
Page 61
Chapter 4 Tutorials Tap on the icon to open the following screen. Use this screen to edit the SSID (WiFi Guest name) and password for your wireless network. Note: If you disable your guest WiFi, be sure to connect to the to manage your WiFi WX3401-1 settings.
Page 62
Chapter 4 Tutorials Tap on Save to save your changes, or tap on Cancel to go back to the previous screen. WX3401-B0 User’s Guide...
Chapter 4 Tutorials 4.8 Account Screen Use this screen to logout or view the app version and privacy policy. 4.9 Setting Up a Secure Wireless Network Thomas wants to set up a wireless network so that he can use his notebook to access the Internet. In this wireless network, the WX3401-B0 serves as an access point (AP), and the notebook is the wireless client.
Chapter 4 Tutorials Thomas has to configure the wireless network settings on the WX3401-B0. Then he can set up a wireless network using WPS (Section 4.9.2 on page 66) or manual configuration (Section 4.9.3 on page 67). 4.9.1 Configuring the Wireless Network Settings This example uses the following parameters to set up a wireless network.
Page 65
Chapter 4 Tutorials Go to the Wireless > Others screen and select 802.11b/g/n/ax Mixed in the 802.11 Mode field. Click Apply. WX3401-B0 User’s Guide...
Chapter 4 Tutorials Thomas can now use the WPS feature to establish a wireless connection between his notebook and the WX3401-B0 (see Section 4.9.2 on page 66). He can also use the notebook’s wireless client to search for the WX3401-B0 (see Section 4.9.2 on page 66).
Chapter 4 Tutorials 4.9.3 Without WPS Use the wireless adapter’s utility installed on the notebook to search for the “Example” SSID. Then enter the “DoNotStealMyWirelessNetwork” pre-shared key to establish a wireless Internet connection. Note: The WX3401-B0 supports IEEE 802.11a/b wireless clients. Make sure that your /g/n/ac/ax notebook or computer’s wireless adapter supports one of these standards.
Page 68
Chapter 4 Tutorials • Employees in Company A will use a general Company wireless network group. • Higher management level and important visitors will use the VIP group. • Visiting guests will use the Guest group, which has a different SSID and password. Company A will use the following parameters to set up the wireless network groups.
Page 69
Chapter 4 Tutorials Click Network Setting > Wireless > Guest/More AP to open the following screen. Click the Edit icon to configure the second wireless network group. Configure the screen using the provided parameters and click Apply. WX3401-B0 User’s Guide...
Page 70
Chapter 4 Tutorials Note: The Guest SSID (Wireless Network Name) depends on the state of the Main SSID. For example, when the 2.4GHz Main SSID is enabled, then the 2.4GHz Guest SSID can be enabled. But when the 2.4GHz Main SSID is disabled, then the 2.4GHz Guest SSID is automatically disabled (cannot be enabled by the user).
Page 71
Chapter 4 Tutorials Check the status of VIP and Guest in the Guest/More AP screen. The yellow bulbs signify that the SSIDs are active and ready for wireless access. Account WX3401-B0 User’s Guide...
H A P T E R Connection Status 5.1 Overview After you log into the Web Configurator, the Connection Status screen appears. You can configure basic Internet access and wireless settings in this screen. It also shows the network status of the WX3401- B0 and computers/devices connected to it.
Chapter 5 Connection Status 5.1.1 Layout Icon Click this icon ( ) to arrange the screen order. Select a block and hold it to move around. Click the Check icon ( ) in the lower left corner to save the changes. 5.1.2 Connectivity Use this screen to view the network connection status of the WX3401-B0 and its clients.
Chapter 5 Connection Status Figure 25 Connectivity: Connected Devices Icon and Device Name You can change the icon and name of a connected device by clicking the device’s Edit icon. Select an icon and/or enter a name in the Device Name field for a connected device. Click Save to save your changes.
Page 76
Chapter 5 Connection Status Click the Arrow icon ( ) to open the following screen. Use this screen to view more information on the status of your firewall and interfaces (LAN, and WiFi). Figure 28 System Info: Detailed Information Each field is described in the following table. Table 7 System Info: Detailed Information LABEL DESCRIPTION...
Chapter 5 Connection Status Table 7 System Info: Detailed Information (continued) LABEL DESCRIPTION MAC Address This shows the wireless adapter MAC (Media Access Control) address of the wireless interface. Status This displays whether WiFi is activated. SSID This is the descriptive name used to identify the WX3401-B0 in a wireless LAN. Channel This is the channel number used by the wireless interface now.
Chapter 5 Connection Status Figure 30 WiFi Settings: Configuration Each field is described in the following table. Table 8 WiFi Settings: Configuration LABEL DESCRIPTION Keep 2.4G and 5G Select this and the 2.4G and 5G wireless networks will use the same SSID. the same If you deselect this, the screen will change.
Page 79
Chapter 5 Connection Status Figure 31 Guest WiFi Settings Click the Arrow icon ( ) to open the following screen. Use this screen to configure the 2.4G and 5G SSIDs and/or passwords for your guest wireless networks. Figure 32 Guest WiFi Settings: Configuration To assign different SSIDs to the 2.4G and 5G guest wireless networks, clear the Keep 2.4G and 5G the same check box in the WiFi Settings screen, and the Guest WiFi Settings screen will change.
Chapter 5 Connection Status Each field is described in the following table. Table 9 WiFi Settings: Configuration LABEL DESCRIPTION WiFi Click this switch to enable or disable the 2.4G and/or 5G wireless networks. When the switch goes to the right , the function is enabled.
Page 81
Chapter 5 Connection Status Figure 35 LAN Setup Each field is described in the following table. Table 10 Status Screen LABEL DESCRIPTION LAN IP Setup IP Address Enter the LAN IPv4 address you want to assign to your WX3401-B0 in dotted decimal notation, for example, 192.168.1.2 (factory default).
H A P T E R Wireless 6.1 Wireless Overview This chapter describes the WX3401-B0’s Network Setting > Wireless screens. Use these screens to set up your WX3401-B0’s WiFi connection and security settings. 6.1.1 What You Can Do in this Chapter This section describes the WX3401-B0’s Wireless screens.
Chapter 6 Wireless WiFi6 / IEEE 802.11ax WiFi6 is backwards compatible with IEEE 802.11a/b/g/n/ac and is most suitable in areas with a high concentration of users. WiFi6 devices support Target Wakeup Time (TWT) allowing them to automatically power down when they are inactive. The following table displays the comparison of the different WiFi standards.
Page 84
Chapter 6 Wireless Figure 36 Network Setting > Wireless > General The following table describes the general WiFi labels in this screen. Table 11 Network Setting > Wireless > General LABEL DESCRIPTION Wireless Wireless Select Keep the same settings for 2.4G and 5G wireless networks and the 2.4 GHz and 5 GHz wireless networks will use the same SSID and wireless security settings.
Page 85
Chapter 6 Wireless Table 11 Network Setting > Wireless > General (continued) LABEL DESCRIPTION Wireless Click this switch to enable or disable WiFi in this field. When the switch turns blue , the function is enabled. Otherwise, it is not. Channel Select a channel from the drop-down list box.
Chapter 6 Wireless Table 11 Network Setting > Wireless > General (continued) LABEL DESCRIPTION Security Mode Select More Secure (Recommended) to add security on this wireless network. The wireless clients which want to associate to this network must have same wireless security settings as the WX3401- B0.
Page 87
Chapter 6 Wireless Figure 38 Wireless > General: More Secure: WPA2-PSK The following table describes the labels in this screen. Table 13 Wireless > General: More Secure: WPA2-PSK LABEL DESCRIPTION Security Level Select More Secure to enable WPA2-PSK data encryption. Security Mode Select the data encryption method the WX3401-B0 uses.
Chapter 6 Wireless 6.3 Guest/More AP This screen allows you to configure a guest wireless network that allows access to the Internet only through the WX3401-B0. You can also configure additional wireless networks, each with different security settings, in this screen. Click Network Setting >...
Page 89
Chapter 6 Wireless Figure 40 Network Setting > Wireless > Guest/More AP > Edit The following table describes the fields in this screen. Table 16 Network Setting > Wireless > Guest/More AP > Edit LABEL DESCRIPTION Wireless Network Setup Wireless Click this switch to enable or disable WiFi in this field.
Chapter 6 Wireless Table 16 Network Setting > Wireless > Guest/More AP > Edit (continued) LABEL DESCRIPTION Access Scenario If you select Home Guest, clients can connect to each other directly. If you select External Guest, clients are blocked from connecting to each other directly. BSSID This shows the MAC address of the wireless interface on the WX3401-B0 when WiFi is enabled.
Page 91
Chapter 6 Wireless Setting > Wireless > MAC Authentication. The screen appears as shown. Figure 41 Network Setting> Wireless > MAC Authentication The following table describes the labels in this screen. Table 17 Network Setting > Wireless > MAC Authentication LABEL DESCRIPTION General...
Chapter 6 Wireless 6.4.1 Add/Edit MAC Addresses Click Add new MAC address in the Network Setting > Wireless > MAC Authentication screen to add a new MAC address. You can also click the Edit icon next to a MAC authentication rule to edit the rule. Enter the MAC addresses of the wireless devices that are allowed or denied access to the WX3401-B0 in these address fields.
Page 93
Chapter 6 Wireless Figure 43 Network Setting > Wireless > WPS The following table describes the labels in this screen. Table 18 Network Setting > Wireless > WPS LABEL DESCRIPTION General Click this switch to activate or deactivate WPS on this WX3401-B0. When the switch turns blue , the function is enabled.
Chapter 6 Wireless Table 18 Network Setting > Wireless > WPS (continued) LABEL DESCRIPTION Register Enter the PIN of the device that you are setting up a WPS connection with and click Register to authenticate and add the wireless device to your wireless network. You can find the PIN either on the outside of the device, or by checking the device’s settings.
Chapter 6 Wireless Figure 44 Network Setting > Wireless > WMM Note: WMM cannot be disabled if 802.11 mode includes 802.11n or 802.11ac. The following table describes the labels in this screen. Table 19 Network Setting > Wireless > WMM LABEL DESCRIPTION WMM of SSID1~4 Select On to have the WX3401-B0 automatically give the wireless network (SSIDx) a priority level...
Page 96
Chapter 6 Wireless Figure 45 Network Setting > Wireless > Others The following table describes the labels in this screen. Table 20 Network Setting > Wireless > Others LABEL DESCRIPTION Output Power Set the output power of the WX3401-B0. If there is a high density of APs in an area, decrease the output power to reduce interference with other APs.
Chapter 6 Wireless Table 20 Network Setting > Wireless > Others (continued) LABEL DESCRIPTION 802.11 Mode For 2.4 GHz frequency WiFi devices: • Select 802.11b Only to allow only IEEE 802.11b compliant WiFi devices to associate with the WX3401-B0. • Select 802.11g Only to allow only IEEE 802.11g compliant WiFi devices to associate with the WX3401-B0.
Chapter 6 Wireless Note: If the current channel is a DFS channel, the warning ‘Channel scan process is denied because current channel is a DFS channel (Channel: 52~140). If you want to run channel scan, please select a non-DFS channel and try again.’ appears. Figure 46 Network Setting >...
Page 99
Chapter 6 Wireless Figure 47 Network Setting > Wireless > Operating Modes The following table describes the labels in this screen. Table 21 Network Setting > Wireless > Operating Modes LABEL DESCRIPTION Operating Modes Modes This displays the operating mode of the WX3401-B0. •...
Chapter 6 Wireless Table 21 Network Setting > Wireless > Operating Modes LABEL DESCRIPTION Select this to activate or deactivate the WPS method. Click WPS button Click this to connect the WX3401-B0 to the AP using the WPS method. Apply Click Apply to save your changes.
Chapter 6 Wireless Table 22 Network Setting > Wireless > AP List LABEL DESCRIPTION SSID This shows the network name of the AP the WX3401-B0 can detect. MAC Address This shows the MAC address of the AP. Channel This shows the channel the AP uses. RSSI (dbm) This shows the strength of the AP’s radio signal measured in dbm.
Page 102
Chapter 6 Wireless Figure 49 Example of a Wireless Network The wireless network is the part in the blue circle. In this wireless network, devices A and B use the access point (AP) to interact with the other devices (such as the printer) or with the Internet. Your WX3401-B0 is the AP.
Chapter 6 Wireless 6.11.2 Additional Wireless Terms The following table describes some wireless network terms and acronyms used in the WX3401-B0’s Web Configurator. Table 23 Additional Wireless Terms TERM DESCRIPTION RTS/CTS Threshold In a wireless network which covers a large area, wireless devices are sometimes not aware of each other’s presence.
Page 104
Chapter 6 Wireless Vanishing Point (which you know was made in 1971) you could use “70dodchal71vanpoi” as your security key. The following sections introduce different types of wireless security you can set up in the wireless network. 6.11.3.1 SSID Normally, the WX3401-B0 acts like a beacon and regularly broadcasts the SSID in the area. You can hide the SSID instead, in which case the WX3401-B0 does not broadcast the SSID.
Chapter 6 Wireless 6.11.3.4 Encryption Wireless networks can use encryption to protect the information that is sent in the wireless network. Encryption is like a secret code. If you do not know the secret code, you cannot understand the message. Many types of encryption use a key to protect the information in the wireless network.
Chapter 6 Wireless Figure 50 Basic Service Set 6.11.6 MBSSID Traditionally, you need to use different APs to configure different Basic Service Sets (BSSs). As well as the cost of buying extra APs, there is also the possibility of channel interference. The WX3401-B0’s MBSSID (Multiple Basic Service Set IDentifier) function allows you to use one access point to provide several BSSs simultaneously.
Chapter 6 Wireless Use long preamble if you are unsure what preamble mode other wireless devices on the network support, and to provide more reliable communications in busy wireless networks. Use short preamble if you are sure all wireless devices on the network support it, and to provide more efficient communications.
Page 108
Chapter 6 Wireless 6.11.8.2 PIN Configuration Each WPS-enabled device has its own PIN (Personal Identification Number). This may either be static (it cannot be changed) or dynamic (in some devices you can generate a new PIN by clicking on a button in the configuration interface).
Page 109
Chapter 6 Wireless Figure 51 Example WPS Process: PIN Method 6.11.8.3 How WPS Works When two WPS-enabled devices connect, each device must assume a specific role. One device acts as the registrar (the device that supplies network and security settings) and the other device acts as the enrollee (the device that receives network and security settings.
Page 110
Chapter 6 Wireless Figure 52 How WPS Works The roles of registrar and enrollee last only as long as the WPS setup process is active (two minutes). The next time you use WPS, a different device can be the registrar if necessary. The WPS connection process is like a handshake;...
Page 111
Chapter 6 Wireless Figure 53 WPS: Example Network Step 1 In step 2, you add another wireless client to the network. You know that Client 1 supports registrar mode, but it is better to use AP1 for the WPS handshake with the new client since you must connect to the access point anyway in order to use the network.
Page 112
Chapter 6 Wireless Figure 55 WPS: Example Network Step 3 6.11.8.5 Limitations of WPS WPS has some limitations of which you should be aware. • WPS works in Infrastructure networks only (where an AP and a wireless client communicate). It does not work in Ad-Hoc networks (where there is no AP).
Page 113
Chapter 6 Wireless point is the WPS registrar, the enrollee, or was not involved in the WPS handshake; a rogue device must still associate with the access point to gain access to the network. Check the MAC addresses of your wireless clients (usually printed on a label on the bottom of the device). If there is an unknown MAC address you can remove it or reset the AP.
H A P T E R Home Networking 7.1 Home Networking Overview A Local Area Network (LAN) is a shared communication system to which many networking devices are connected. It is usually located in one immediate area such as a building or floor of a building. Use the LAN screens to help you configure a LAN DHCP server and manage IP addresses.
Chapter 7 Home Networking 7.2 Home Networking Screen Use this screen to set the IP address and subnet mask of your WX3401-B0. Configure DHCP settings to have a DHCP server assign IP addresses to devices. Click Network Setting > Home Networking to open the Home Networking screen.
Page 116
Chapter 7 Home Networking Table 24 Network Setting > Home Networking > LAN Setup (continued) LABEL DESCRIPTION Subnet Mask Type the subnet mask of your network in dotted decimal notation, for example 255.255.255.0 (factory default). Your WX3401-B0 automatically computes the subnet mask based on the IP address you enter, so do not change this field unless you are instructed to do so.
H A P T E R 8.1 Log Overview These screens allow you to determine the categories of events that the WX3401-B0 logs and then display these logs or have the WX3401-B0 send them to an administrator (through e-mail) or to a syslog server. 8.1.1 What You Can Do in this Chapter •...
Chapter 8 Log 8.2 System Log Settings Use the Log screen to see the system logs. You can filter the entries by selecting a severity level and/or category. Click System Monitor > Log > System Log to open the System Log screen. Figure 58 System Monitor >...
Page 119
Chapter 8 Log Table 26 System Monitor > Log > System Log (continued) LABEL DESCRIPTION Facility The log facility allows you to send logs to different files in the syslog server. Refer to the documentation of your syslog program for more details. Level This field displays the severity level of the log.
H A P T E R Multicast Status 9.1 Multicast Status Overview Use the Multicast Status screens to view IPv4 or IPv6 multicast group information. 9.2 IGMP Status Use this screen to look at the current list of IPv4 multicast groups the WX3401-B0 manages through IGMP. Internet Group Multicast Protocol (IGMP) is a network-layer protocol used to establish membership in a Multicast group - it is not used to carry user data.
Page 121
Chapter 9 Multicast Status settings in Network Setting > MLD Status. To open this screen, click System Monitor > Multicast Status > MLD Status. Figure 60 System Monitor > Multicast Status > MLD Status The following table describes the labels in this screen. Table 28 System Monitor >...
H A P T E R WLAN Station Status 10.1 WLAN Station Status Overview Click System Monitor > WLAN Station Status to open the following screen. Use this screen to view information and status of the wireless stations (wireless clients) that are currently associated with the WX3401-B0.
Page 123
Chapter 10 WLAN Station Status Table 29 System Monitor > WLAN Station Status (continued) LABEL DESCRIPTION The Signal-to-Noise Ratio (SNR) is the ratio between the received signal power and the received noise power. The normal range is 15 to 40. If the value drops below 15, try moving the associated wireless station closer to the WX3401-B0 to get better quality WiFi.
H A P T E R System 11.1 System Overview In the System screen, you can name your WX3401-B0 (Host) and give it an associated domain name. Domain is the name given to a network. It will be required to reach a network from an external point (like the Internet).
Chapter 12 User Account H A P T E R User Account 12.1 User Account Overview In the User Account screen, you can view the settings of the ‘admin’ and other user accounts that you use to log into the WX3401-B0 to manage it. 12.2 User Account Settings Click Maintenance >...
Chapter 12 User Account Table 31 Maintenance > User Account (continued) LABEL DESCRIPTION Retry Times This field displays the number of times consecutive wrong passwords can be entered for this account. 0 means there is no limit. Idle Timeout This field displays the length of inactive time before the WX3401-B0 will automatically log the user out of the Web Configurator.
Page 127
Chapter 12 User Account Table 32 Maintenance > User Account > Add/Edit (continued) LABEL DESCRIPTION Password Type your new system password. The Password must contain 6 to 64 characters, including 0 to 9 and a to z. Note that as you type a password, the screen displays a (*) for each character you type.
H A P T E R Remote Management 13.1 Remote Management Overview Use remote management to control what services you can use through which interface(s) in order to manage the WX3401-B0. 13.1.1 What You Can Do in this Chapter • Use the Remote Management screen to allow various approaches to access the WX3401-B0 remotely from a LAN connection (Section 13.2 on page 128).
Page 129
Chapter 13 Remote Management The following table describes the fields in this screen. Table 33 Maintenance > Remote Management > Remote Management LABEL DESCRIPTION Service This is the service list you may use to access the WX3401-B0. • HTTP provides a non secured way. •...
H A P T E R Time Settings 14.1 Time Settings Overview This chapter shows you how to configure the WX3401-B0’s system date and time. 14.2 Time For effective scheduling and logging, the WX3401-B0’s system time must be accurate. Use this screen to configure the WX3401-B0’s time based on your local time zone.
Page 131
Chapter 14 Time Settings Figure 66 Maintenance > Time The following table describes the fields in this screen. Table 34 Maintenance > Time LABEL DESCRIPTION Current Date/Time Current Time This field displays the time of your WX3401-B0. Each time you reload this page, the WX3401-B0 synchronizes the time with the time server. Current Date This field displays the date of your WX3401-B0.
Page 132
Chapter 14 Time Settings Table 34 Maintenance > Time (continued) LABEL DESCRIPTION Time Zone Choose the time zone of your location. This will set the time difference between your time zone and Greenwich Mean Time (GMT). Daylight Savings Daylight Saving Time is a period from late spring to early fall when many countries set their clocks ahead of normal local time by one hour to give more daytime light in the evening.
H A P T E R Firmware Upgrade 15.1 Firmware Upgrade Overview This screen lets you upload new firmware to your WX3401-B0. You can download new firmware releases from your nearest Zyxel FTP site (or www.zyxel.com) to upgrade your device’s performance. Only use firmware for your device’s specific model.
Page 134
Chapter 15 Firmware Upgrade The following table describes the labels in this screen. After you see the firmware updating screen, wait two minutes before logging into the WX3401-B0 again. Table 35 Maintenance > Firmware Upgrade LABEL DESCRIPTION Upgrade Firmware Restore Default Select the check box to have the WX3401-B0 automatically reset itself after the new firmware is Settings After uploaded.
Page 135
Chapter 15 Firmware Upgrade Note that the WX3401-B0 automatically restarts during the upload, causing a temporary network disconnect. In some operating systems, you may see the following icon on your desktop. Network Temporarily Disconnected WX3401-B0 User’s Guide...
H A P T E R Backup/Restore 16.1 Backup/Restore Overview The Backup/Restore screen allows you to backup and restore device configurations. You can also reset your device settings back to the factory default. 16.2 Backup/Restore Settings Click Maintenance > Backup/Restore. Information related to factory default settings and backup configuration are shown in this screen.
Page 137
Chapter 16 Backup/Restore Backup Configuration Backup Configuration allows you to back up (save) the WX3401-B0’s current configuration to a file on your computer. Once your WX3401-B0 is configured and functioning properly, it is highly recommended that you back up your configuration file before making configuration changes. The backup configuration file will be useful in case you need to return to your previous settings.
Chapter 16 Backup/Restore Reset to Factory Defaults Click the Reset button to clear all user-entered configuration information and return the WX3401-B0 to its factory defaults. The following warning screen appears. Figure 73 Reset Warning Message Figure 74 Reset In Process Message You can also press the RESET button on the rear panel to reset the factory defaults of your WX3401-B0.
Chapter 17 Diagnostic H A P T E R Diagnostic 17.1 Diagnostic Overview The Diagnostic screens display information to help you identify problems with the WX3401-B0. The route between a Central Office Very-high-bit-rate Digital Subscriber Line (CO VDSL) switch and one of its Customer-Premises Equipment (CPE) may go through switches owned by independent organizations.
Chapter 17 Diagnostic 17.3 Ping & TraceRoute Use this screen use ping, traceroute, or nslookup for troubleshooting. Ping and traceroute are used to test whether a particular host is reachable. After entering an IP address and clicking on one of the buttons to start a test, the results will be shown in the Ping/Traceroute Test area.
H A P T E R Troubleshooting This chapter offers some suggestions to solve problems you might encounter. The potential problems are divided into the following categories. • Power, Hardware Connections, and LEDs • WX3401-B0 Access and Login • Internet Access •...
Chapter 18 Troubleshooting Turn the WX3401-B0 off and on. If the problem continues, contact the vendor. 18.2 WX3401-B0 Access and Login I forgot the IP address for the WX3401-B0. The default LAN IP address is 192.168.1.2. If your router assigns an IP address to the WX3401-B0, you can find your new IP address on the Gateway Detail screen using the MPro Mesh App (See Section 4.4.2 on page 44 for more information) or log into...
Chapter 18 Troubleshooting Reset the device to its factory defaults, and try to access the WX3401-B0 with the default IP address. See Section 2.5.1 on page If the problem continues, contact the network administrator or vendor, or try one of the advanced suggestions.
Chapter 18 Troubleshooting I cannot connect to the Internet using an Ethernet connection. • Make sure you have the Ethernet LAN port connected to a MODEM or Router. (see Section 4.3.2 on page 36 for more information) I cannot access the WX3401-B0 anymore. I had access to the WX3401-B0, but my connection is not available anymore.
Chapter 18 Troubleshooting To optimize the speed and quality of your wireless connection, you can: • Move your wireless device closer to the AP if the signal strength is low. • Reduce wireless interference that may be caused by other wireless networks or surrounding wireless electronics such as cordless phones.
Page 148
Chapter 18 Troubleshooting Click Change adapter settings. Right-click the Ethernet icon, and then select Properties. WX3401-B0 User’s Guide...
Page 149
Chapter 18 Troubleshooting Click Internet Protocol Version 4 (TCP/IPv4) and then click Properties. Select Use the following IP address and enter an IP address from 192.168.1.3 to 192.168.1.254. The Subnet mask will be entered automatically. WX3401-B0 User’s Guide...
Chapter 18 Troubleshooting Click OK when you are done and close all windows. 18.6 Resetting the WX3401-B0 to Its Factory Defaults If you reset the WX3401-B0, you lose all of the changes you have made. The WX3401-B0 re-loads its default settings, and the password resets to the back-label default key. You have to make all of your changes again.
Chapter 18 Troubleshooting 18.7 MPro Mesh App Problems I cannot use the MPro Mesh app to manage my wireless network. • Make sure you connect your mobile device to the controller (Zyxel MPro Mesh Router in Scenario 1 and WX3401-B0-1 in Scenario 2) in order to manage the wireless network. •...
• Brief description of the problem and the steps you took to solve it. Corporate Headquarters (Worldwide) Taiwan • Zyxel Communications Corporation • http://www.zyxel.com Asia China • Zyxel Communications (Shanghai) Corp. Zyxel Communications (Beijing) Corp. Zyxel Communications (Tianjin) Corp. • https://www.zyxel.com/cn/zh/ India • Zyxel Technology India Pvt Ltd • https://www.zyxel.com/in/en/ Kazakhstan •...
Page 154
Appendix A Customer Support • https://www.zyxel.com/be/fr/ Bulgaria • Zyxel България • https://www.zyxel.com/bg/bg/ Czech Republic • Zyxel Communications Czech s.r.o • https://www.zyxel.com/cz/cs/ Denmark • Zyxel Communications A/S • https://www.zyxel.com/dk/da/ Estonia • Zyxel Estonia • https://www.zyxel.com/ee/et/ Finland • Zyxel Communications • https://www.zyxel.com/fi/fi/ France •...
Page 155
• Zyxel Communications Poland • https://www.zyxel.com/pl/pl/ Romania • Zyxel Romania • https://www.zyxel.com/ro/ro Russia • Zyxel Russia • https://www.zyxel.com/ru/ru/ Slovakia • Zyxel Communications Czech s.r.o. organizacna zlozka • https://www.zyxel.com/sk/sk/ Spain • Zyxel Communications ES Ltd • https://www.zyxel.com/es/es/ Sweden • Zyxel Communications • https://www.zyxel.com/se/sv/ Switzerland •...
Page 156
Appendix A Customer Support Turkey • Zyxel Turkey A.S. • https://www.zyxel.com/tr/tr/ • Zyxel Communications UK Ltd. • https://www.zyxel.com/uk/en/ Ukraine • Zyxel Ukraine • http://www.ua.zyxel.com South America Argentina • Zyxel Communications Corporation • https://www.zyxel.com/co/es/ Brazil • Zyxel Communications Brasil Ltda. • https://www.zyxel.com/br/pt/ Colombia •...
Page 157
Appendix A Customer Support Middle East • Zyxel Communications Corporation • https://www.zyxel.com/me/en/ North America • Zyxel Communications, Inc. - North America Headquarters • https://www.zyxel.com/us/en/ Oceania Australia • Zyxel Communications Corporation • https://www.zyxel.com/au/en/ Africa South Africa • Nology (Pty) Ltd. • https://www.zyxel.com/za/en/...
P P E N D I X IPv6 Overview IPv6 (Internet Protocol version 6), is designed to enhance IP address size and features. The increase in IPv6 address size to 128 bits (from the 32-bit IPv4 address) allows up to 3.4 x 10 IP addresses.
Page 159
Appendix B IPv6 Unspecified Address An unspecified address (0:0:0:0:0:0:0:0 or ::) is used as the source address when a device does not have its own address. It is similar to “0.0.0.0” in IPv4. Loopback Address A loopback address (0:0:0:0:0:0:0:1 or ::1) allows a host to send packets to itself. It is similar to “127.0.0.1” in IPv4.
Page 160
Appendix B IPv6 Table 40 Reserved Multicast Address (continued) MULTICAST ADDRESS FF0E:0:0:0:0:0:0:0 FF0F:0:0:0:0:0:0:0 Subnet Masking Both an IPv6 address and IPv6 subnet mask compose of 128-bit binary digits, which are divided into eight 16-bit blocks and written in hexadecimal notation. Hexadecimal uses four bits for each character (1 ~ 10, A ~ F).
Page 161
Appendix B IPv6 Renew Renew Renew Rebind to S1 to S1 to S1 to S2 Renew Renew Renew Rebind to S1 to S1 to S1 to S2 DHCP Relay Agent A DHCP relay agent is on the same network as the DHCP clients and helps forward messages between the DHCP server and clients.
Page 162
Appendix B IPv6 • Router advertisement: A response to a router solicitation or a periodical multicast advertisement from a router to advertise its presence and other parameters. IPv6 Cache An IPv6 host is required to have a neighbor cache, destination cache, prefix list and default router list. The WX3401-B0 maintains and updates its IPv6 caches constantly using the information from response messages.
Page 163
Appendix B IPv6 Example - Enabling IPv6 on Windows XP/2003/Vista By default, Windows XP and Windows 2003 support IPv6. This example shows you how to use the ipv6 install command on Windows XP/2003 to enable IPv6. This also displays how to use the ipconfig command to see auto-generated IP addresses.
Page 164
Appendix B IPv6 Click Start and then OK. Now your computer can obtain an IPv6 address from a DHCPv6 server. Example - Enabling IPv6 on Windows 7 Windows 7 supports IPv6 by default. DHCPv6 is also enabled when you enable IPv6 on a Windows 7 computer.
Page 165
Appendix B IPv6 Click Close to exit the Local Area Connection Status screen. Select Start > All Programs > Accessories > Command Prompt. Use the ipconfig command to check your dynamic IPv6 address. This example shows a global address (2001:b021:2d::1000) obtained from a DHCP server. C:\>ipconfig Windows IP Configuration Ethernet adapter Local Area Connection:...
P P E N D I X Services The following table lists some commonly-used services and their associated protocols and port numbers. • Name: This is a short, descriptive name for the service. You can use this one or create a different one, if you like.
Page 167
Appendix C Services Table 41 Examples of Services NAME PROTOCOL PORT(S) DESCRIPTION AH (IPSEC_TUNNEL) User-Defined The IPSEC AH (Authentication Header) tunneling protocol uses this service. 5190 AOL’s Internet Messenger service. AUTH Authentication protocol used by some servers. Border Gateway Protocol. BOOTP_CLIENT DHCP Client.
Page 168
Appendix C Services Table 41 Examples of Services (continued) NAME PROTOCOL PORT(S) DESCRIPTION 2049 Network File System - NFS is a client/server distributed file service that provides transparent file sharing for network environments. NNTP Network News Transport Protocol is the delivery mechanism for the USENET newsgroup service.
Page 169
Appendix C Services Table 41 Examples of Services (continued) NAME PROTOCOL PORT(S) DESCRIPTION TACACS Login Host Protocol used for (Terminal Access Controller Access Control System). TELNET Telnet is the login and terminal emulation protocol common on the Internet and in UNIX environments. It operates over TCP/IP networks.
Regulatory Notice and Statement UNITED STATES of AMERICA The following information applies if you use the product within USA area. US Importer: Zyxel Communications, Inc, 1130 North Miller Street Anaheim, CA92806-2001, https://www.zyxel.com/us/en/ FCC EMC Statement • The device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Page 171
Appendix D Legal Information Innovation, Science and Economic Development Canada RSS-GEN & RSS-247 Statement • This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Page 172
Appendix D Legal Information Български С настоящото Zyxel декларира, че това оборудване е в съответствие със съществените изисквания и другите (Bulgarian) приложими разпоредбите на Директива 2014/53/ЕC. National Restrictions • The Belgian Institute for Postal Services and Telecommunications (BIPT) must be notified of any outdoor wireless link having a range exceeding 300 meters.
Page 173
Appendix D Legal Information Română Prin prezenta, Zyxel declară că acest echipament este în conformitate cu cerinţele esenţiale şi alte prevederi relevante ale (Romanian) Directivei 2014/53/UE. Slovenčina Zyxel týmto vyhlasuje, že zariadenia spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 2014/53/EÚ. (Slovak) Slovenščina Zyxel izjavlja, da je ta oprema v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 2014/53/EU.
Page 174
Appendix D Legal Information • CAUTION: Risk of explosion if battery is replaced by an incorrect type, dispose of used batteries according to the instruction. Dispose them at the applicable collection point for the recycling of electrical and electronic devices. For detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the store where you purchased the product.
Page 176
Appendix D Legal Information Explanation of the Symbols SYMBOL EXPLANATION Alternating current (AC): AC is an electric current in which the flow of electric charge periodically reverses direction. Direct current (DC): DC if the unidirectional flow or movement of electric charge carriers. Earth;...
Index Index copyright CTS threshold customer support activation SSID authentication 103, 104 RADIUS server daisy chain 12, 13 data fragment threshold disclaimer backup configuration Basic Service Set, see BSS example encryption Extended Service Set IDentification 85, 89 CCMs certifications filters viewing MAC address 90, 104...
Page 178
Index Restart logs 117, 120 Theme Loop Back Response, see LBR IEEE 802.11ax loopback IGMP multicast group list Internet Protocol version 6, see IPv6 IP address ping IPv6 addressing EUI-64 MAC address global address filter interface ID 90, 104 link-local address MAC authentication Neighbor Discovery Protocol Maintenance Association, see MA...
Page 179
Index Push Button Configuration, see PBC system information push button, WPS Theme icon RADIUS server thresholds data fragment reset RTS/CTS Reset button time Reset the device TWT (Target Wakeup Time) restart Restart icon restoring configuration RFC 3164 RTS threshold upgrading firmware screen order warranty change...
Page 180
Index status 107, 109 example limitations push button WiFi overview WiFi setting configuration WiFi6 introduction wireless basics wireless channel wireless group multiple setup wireless LAN wireless network secure setup wireless security troubleshooting wireless tutorial 22, 107, 109 example limitations example push button WPS button WPS methods...
Need help?
Do you have a question about the WX3401-BO and is the answer not in the manual?
Questions and answers