Advertisement
Quick Links
:',~-.'
OPERATOR'S MANUAL
ROTARY
42"
MOWER
MODELS:
AGT42D
UT36037
..JACOBSEN
HOMELITE
IFINCORRECTLY USEDTHISMACHINECANCAUSE SEVERE INJURY.
THOSE WHOUSE AND
AWARNING
MAINTAIN THE MACHINE SHOULD BETRAINED INITS PROPER USE,
WARNED OFITS DANGERS,
AND SHOULD READTHE ENTIRE MANUALBEFORE ATTEMPTING TO SET UP,
OPERATE,ADJUST
OR SERVICE THE MACHINE.
PART NO. JA-99211-0
Advertisement
Related Manuals for Jacobsen AGT42D
Summary of Contents for Jacobsen AGT42D
- Page 1 :',~-.' OPERATOR'S MANUAL ROTARY 42" MOWER MODELS: AGT42D UT36037 ..JACOBSEN HOMELITE IFINCORRECTLY USEDTHISMACHINECANCAUSE SEVERE INJURY. THOSE WHOUSE AND AWARNING MAINTAIN THE MACHINE SHOULD BETRAINED INITS PROPER USE, WARNED OFITS DANGERS, AND SHOULD READTHE ENTIRE MANUALBEFORE ATTEMPTING TO SET UP, OPERATE,ADJUST OR SERVICE THE MACHINE.
- Page 2 SAFETY PRECAUTIONS THE FOLLOWINGPRECAUTIONS ARE SUGGESTED TO HELP PREVENTACCIDENTS. A CAREFUL OPERATOR ISTHE BEST OPERATOR. MOST ACCIDENTS CAN BEAVOIDED BYOBSERVING CERTAIN PRECAUTIONS. READANDTAKE THE FOLLOWING PRECAUTIONS BEFORE OPERATING THIS TRACTOR TO HELP PREVENTACCIDENTS. EQUIPMENT SHOULD BEOPERATED ONLY BYTHOSE WHO ARE RESPONSIBLE AND INSTRUCTED TO DOSO. THE TRACTOR Do not start the engine or operate controls...
- Page 3 When using the vehicle withmower, proceed as Watch out for traffic when crossing or near follows: roadways. Itis recommended that this machine notbeused a) Mowonly in daylight or ingood artificallight. on public roads. However, if riding on public b) Never make a cutting height adjustment while roads is unavoidable you must comply to equip-...
- Page 4 CONTENTS SAFETY PRECAUTIONS............2-3 SAFETY DEFINITIONS. .
- Page 5 SET-UP INSTRUCTIONS DEFINITIONS OF DIRECTIONS 2. Assemble discharge chute deflector tounderside of mower housing, using two (short) carriage bolts, flat used throughout this manual, following washers, lockwashers, nuts, by inserting definitions apply: "Right" and "Left" refer fo the carriage bolts through deflector andthen through operator's right and left when seated in the normal...
- Page 6 1.1/2" (3.81em) rPIN ~GRIP LIFT HANDLE 4-1/2" (11.43 em) (TRANSPORT) FIGURE4 FIGURE3 IMPLEMENT LIFT HANDLE ELECTRIC The mower is raised or lowered manually by the CLUTCHSWITCH implement Ii.ft handle. Moving thelift handle rearward as far aspossible and locking the handle inthe nearest notch inthe quadrant (See Fig.
- Page 7 the implement lift handle perthe Instructions on Page 5. If the tractor has a hydraulic lift, set the cutting height by using the position control as follows: (See Fig. 3). a. Raise mowerto transport position. NEW CUTTER BAR b. LoosenLock Bar. c.
- Page 8 MAINTENANCE receives anequal amount of grinding to prevent having unbalanced which will cause excessive vibrations at high speeds and maydamage the mower. A WARNING Incorrect resharpening ofthe cutter bar as illustrated in"A", Fig. 10,may result in serious bodily injuryshould FIGURE8 the sudden impact ofthe bar anda foreign object occur during operation...
- Page 9 of holesto makeit shorter and raisethe lowside of 7. Push down the lift linkage manually, thenslide the the mower. mower forward, making surethe front and rearhitch brackets areinside the mower lift arms. Lift mower 2. Blade Tilt: Position cutter blade parallel to tractor with implement lift handle to lockfront...
- Page 10 .the spring is completely (solid) compressed. If the latch fromthefront hanger bar. '811owable inside movement between the totaLspring coils is 118"(3.17 mm) or less, the spring should be d. Slide the mower to the rear as far as possible, adjusted by turning the nut on the rodextending rembving it from the lift linkage.
- Page 11 STORAGE MOWER At the endof the mowing season, or if the mower is to WASHING be stored for any length of time, the following steps are recommended. We recommend washing the mower with ahose to prevent the accumulation of grass clippings and dirt and to keepthe unit operating efficiently.