Advertisement

PARTS & OPERATORS MANUAL
PEGASUS
4000-6000
WWW.CROPLANDS.COM.AU
BT-POM 00808 Rev 3B
STOP
BEFORE COMMENCING
operation, ENSURE you read
& understand this manual, its
contents, and any additional
information supplied.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PEGASUS 4000 and is the answer not in the manual?

Questions and answers

Summary of Contents for Croplands PEGASUS 4000

  • Page 1 PARTS & OPERATORS MANUAL PEGASUS 4000-6000 STOP BEFORE COMMENCING WWW.CROPLANDS.COM.AU operation, ENSURE you read & understand this manual, its contents, and any additional information supplied. BT-POM 00808 Rev 3B...
  • Page 2: Table Of Contents

    Contents Foreword Important Information Section 1 Pre-Operation Section 2 Sprayer Operation Section 3 Sprayer Calibration Section 4 Lubrication & Maintenance Section 5 Trouble Shooting Section 6 Assembly Drawings & Parts Listings Section 7 Pegasus BT-POM 1212 - Rev 3...
  • Page 3: Foreword

    Your Sprayer This manual provides assembly, These terms/symbols used throughout setting up, operating and maintenance this manual: 1. Before attempting to use your instructions for the Croplands Pegasus • NOTE - to convey useful sprayer, make sure you sprayer. operating information.
  • Page 4: Important Information

    Important Information Section 1 Introduction General Specifications Warranty Policy Safety Shipping Information & Product ID Pegasus BT-POM 1212 - Rev 3...
  • Page 5: Introduction

    Croplands has taken steps to ensure this operator’s manual is as current and as accurate as possible. Due to the ever-changing markets of cropping and farming, Croplands is constantly striving to be at the forefront of innovation and technology. While the information in this manual is considered accurate at the time of writing, Croplands reserves the right to change this information without notice.
  • Page 6: General Specifications

    General Specifications Important Information 6000 litre Pegasus with 20.8 x 42 single wheels. General Description & Pump Chemical handling Boom & Lift Specifications AR positive displacement oil-bath four Integrated chemical mixer/induction unit 24, 28, 30, 33 & 36 metre booms are diaphragm pump, chemical resistant, is fitted with a drop-leg device.
  • Page 7: Warranty Policy

    • the Sprayer’s unique serial number, WARRANTY & PRE-DELIVERY • the Sprayer’s specification sheet, BROADACRE • a pre-delivery checklist and • outlines the Croplands Warranty policy. STOP Always contact your Croplands Dealer first and foremost for warranty matters. BEFORE COMMENCING WWW.CROPLANDS.COM.AU...
  • Page 8: Safety

    This includes the Croplands Operators Safety Manual – as pictured here. OPERATORS This manual is available on the Croplands SAFETY Web site, or for printed versions contact Croplands customer support and ask for MANUAL part number GP-SAFE-A (or later version if available).
  • Page 9: Shipping Information & Product Id

    Shipping Information & Product ID Section 1 Use the tie-down points provided when transporting. Pegasus Serial Number AR Pump Serial Number 6000 litre Pegasus with 20.8 x 42 single wheels. Shipping Information Product Pegasus Serial Number Pump Serial Number Plate Plate Identification The Pump Serial Number Plate is located...
  • Page 10: Pre-Operation

    Section 2 Pre-Operation Hook-up Un-hook 2.11 Main Controls & Functions 2.12 Pre-Operation Check 2.13 Pegasus BT-POM 1212 - Rev 3...
  • Page 11 Section 2 Hook-up The Pegasus is fully assembled at the factory. Adjust the hitch jack until the work platform is level. Remove the pin adjust the hitch height as required. Assembly Connect the 1. Connect the Pegasus To adjust the hitch height: Hitch to the Tractor a) Using the front and/or rear pins Instructions...
  • Page 12 Pre-Operation Hook-up Correctly fit the PTO shaft to the Pegasus. Unpin and lift up the lift jack base. 2 Fit the PTO Shaft 3. Measure and fit the PTO to the 3 Insert the drawbar pin & lock the retaining pin in position to ensure the Pegasus ensuring the locking pin This section is not applicable to any pin cannot come out while...
  • Page 13 Section 2 Hook-up The tractor-sprayer hitch point should be centred between the two universal joints of the PTO shaft Pivot point of tow hitch centred between PTO universal joints Minimum shaft Standard PTO contact length Make sure shaft ends Make sure shaft ends of 300mm (12") do not butt up.
  • Page 14 (optional) - see following boom lock-plate (see pic). This plate is in place for transport pages. to your dealer from the Croplands' factory. d) If fitted, connect the hoses for the hydraulic pump drive (optional) - Prior to operating remove the boom lock-plate (in position).
  • Page 15 Section 2 Hook-up Electric/hydraulic valves. Connect electric/hydraulic console cables at rear of Hydraulic drive pump. Hose marked with cable-tie is for the PRESSURE line. tractor. 3a. Electric/Hydraulic 3b. Hydraulic Pump Drive 3. Ensure the power leads are If your sprayer is fitted with a connected to the battery terminals hydraulic pump drive, connect the Valves...
  • Page 16 NOTE tractor has this system. the amount of oil bypassed should be kept to a minimum. Consult your Croplands dealer if you require assistance with determining Tractor adjustments may be necessary, pump RPM. consult your dealer if you are unsure.
  • Page 17 Section 2 Hook-up MT3405 Controller standard. Connect the leads of the Controller to loom. Connect the main loom couplings. Dual lines on the boom. 4 Fit the Spray Controller Dual Line Option 2. Connect the leads at the rear of the 4.
  • Page 18 Pre-Operation Hook-up The BA7000 Manual. Mount the Foam Marker Controller in the cab. Connect the 4-pin plugs of the Foam Marker Controller. Connect Foam Marker. 5. Fit the Foam Marker For the operation of dual lines, you will 3. Connect and lock the Foam Marker 5.
  • Page 19 Section 2 Hook-up Connect the main harness cables to the battery. Connect the auxillary power cables to the battery (if fitted). Air tank compressor. Air chamber/tank. 7. Activate the Airbag Ensure air-tank drain valve is shut. 6. Connect Power Leads Suspension The system is fitted with a pressure to the Tractor Battery...
  • Page 20 Pre-Operation Un-hook Disconnect hydralulic hoses & PTO shaft. Disconnect the main loom coupling. Unhitching the 2. Locate the sprayer on level ground and disconnect the: Pegasus from the • PTO shaft, Tractor • Hydraulic hoses - for the boom and/or the hydraulic pump-drive, To disconnect the Pegasus sprayer from •...
  • Page 21 Section 2 Main Controls & Functions The location of the Pegasus main control panel & other valves facilitates central, easy access of all control points for filling, mixing, spraying & cleaning functions: Fill Control Lever Pressure Control Lever (4 operating positions): (4 operating positions): •...
  • Page 22 Pre-Operation Pre-Operation Check Read Operators’ Manuals before operating machine. Check pump oil level. Check pump air chamber pressure. Check the suction filter is clean. Pre-Operation 9. Check diaphragm pump oil level. 10. Check air pressure in the 11. Check the suction filter is clean. diaphragm pump air chamber is 70 Thoroughly clean the suction filter Check List...
  • Page 23 Section 2 Pre-operation Check Check the pressure filter is clean. Airbag Suspension. Check foam marker operates correctly. 12. Check the pressure filter is clean. 13. If fitted, check the airbag 14. Check the foam marker operates 15. Check all Pegasus spraying functions suspension system is working correctly (Refer to Foam Marker (Refer to “Check the Spray Controller...
  • Page 24 Pre-Operation Check MT3405 Controller standard. Place the suction valve in "Spray" position. Rotate the Pressure Control Lever to "Spray" position. Enter the flow meter calibration factor. Check the Spray 2. Fill an appropriate quantity of 4. Rotate the Pressure Control Lever 5.
  • Page 25 Pre-operation Check Adjust the manual pressure relief valve. Check the tank agitator valve is open. +/- keys and auto/man key. Boom switches on, master switch in hold. 9. Adjust the spraying pressure as (e) Use the “-” key to reduce the Turn the Controller Master switch With all boom operating, re-check follows with the tractor &...
  • Page 27: Sprayer Operation

    Sprayer Operation Section 3 Filling Foam Marker Filters Cleaning 3.10 Boom Adjustment: - Boom Set Up - 24 to 30 metre 3.12 - Boom Adjustment - 36 metre 3.14 Boom Operation - All Sizes 3.17 Chemical Mixing 3.18 Airbag Suspension 3.24 Dual Lines 3.25...
  • Page 28 Filling Sprayer Operation Spray tank Fresh Water tank Flush tank Foam Marker tank Open spray tank lid for top-filling. Clean the bottom fill filter. Rotate the Fill Control Lever to "Fill Spray Tank" Rotate the Fill Control Lever to "Fill Flush Tank" position.
  • Page 29 Section 3 Filling Rotate the Fill Control Lever to "Fill Foam Tank" Filling pump (if fitted). Hydraulic supply tap. Orion filling flow-meter. position. Operating the Filling Pump Operating the Orion Filling g) After filling the tanks, rotate the Fill f) Shut the hydraulic supply tap Control Lever to “Off”...
  • Page 30 Filling Sprayer Operation Open Spray tank lid for top-filling. Open Flush tank lid for top-filling. Open Foam tank lid for top-filling/adding concentrate. Top-Filling 2. Flush Tank 3. Foam Marker Tank To top-fill the Spray tank: Use clean, fresh water (preferably The Pegasus incorporates a 130 litre a) Open the Spray tank lid and ensure All Pegasus tanks can be filled via the...
  • Page 31 Operating the Foam 4. Fresh Water Tank Marker The Pegasus incorporates a 30 litre fresh Croplands also offer a water conditioner The performance of the the foam marker water tank for personal safety when if your water has a high mineral content.
  • Page 32 Foam Marker Sprayer Operation Make sure the foam marker liquid filter is clean. Make sure air filter is clean "Left (On) / Off / Right (On)" switch. Foam density control knob. Foam Marker Controller 2. Make sure the air filter is clean. 4.
  • Page 33 Section 3 Foam Marker The foam marker pressure gauge. Adjusted for low foam output. Adjusted for high foam output. Setting Liquid Pressure Adjust the pressure to obtain the best • Generally you won't operate over 55 foam result for your conditions. psi as it will use excessive solution The foam marker injects the foam liquid and create a very wet foam.
  • Page 34 Filters Sprayer Operation WARNING Always wear protective gloves when cleaning filters containing toxic chemicals. Clean bottom-fill filter regularly. Clean suction filter regularly. Clean pressure filter regularly (Inset shows valve). Cleaning Filters Bottom-Fill Filter Suction Filter Pressure Filters The bottom-fill filter should be cleaned The suction filter should be cleaned The pressure line filter should be cleaned Filters are used to stop solids entering...
  • Page 35 Section 3 Filters Clean nozzle filters regularly. Close the filter tap & then remove the filter bowl. After cleaning, replace the screen & filter bowl. Ensure agitator valve is open before adding chemical. Nozzle Filters Foam Marker Filters Tank Agitation 3.
  • Page 36 Cleaning Sprayer Operation Open the Tank Drain valve to drain the tank. Open the Tank Rinse & Agitator valves. Remove and clean the suction filter Remove and clean the pressure filter Flushing the Pegasus 6. Turn the Suction Line valve to 9.
  • Page 37 Section 3 Cleaning Open the Tank Rinse & Agitator valves. Place the suction valve in "Spray" position. Open the Tank Drain valve to drain the tank. Using Tank and 8. Engage PTO and bring the PTO speed 12. If you require the cleaning agent to up to 540 RPM.
  • Page 38 Boom Adjustment - 24 to 30m Sprayer Operation Unique parallelogram boom lift - low position. Unique parallelogram boom lift - high position. Boom Set-Up - 24-30 control are options (see page 2.14). 1. Wing Alignment metre Boom set-up requires: Wings are aligned to the central frame 1.
  • Page 39 Section 3 Boom Adjustment - 24 to 30m 2. Wing Extension Alignment 3. Balancing Device Alignment 4. Backlash Between Sliding After inner wing alignment is completed, The boom is fitted with an adjustable The balancing device oscillation must be 5. Locking the Balancing align the wing extensions by: connecting rod which allows the boom to adjusted so that the surfaces slide freely...
  • Page 40 Boom Adjustment - 36m Sprayer Operation Take the pressure off the boom by nudging the Adjust the nut, until the desired level is found. Adjust the sleeve until the boom is at the desired Finally, adjust the breakaway arm to the desired boom forward.
  • Page 41 Section 3 Grub Screw Boom Wing Section Centre Section 5-10° Rear of boom (this side) Direction of travel Adjustment clevis Ensure the boom wing is slightly forward in relation Remove the grub screws & adjust the clevis, then, Set the bolt stopper to stop the boom at the Lock the nuts in place when set correctly.
  • Page 42 Sprayer Operation Locking lever Horizontal bolt touching front for adjustment of slot Adjust the turnbuckle sleeve until the centre When locked the hook part of the locking lever Loosen the lock nuts and then adjust the horizontal section is level. should be in contact with the front edge of the slot.
  • Page 43 Section 3 Boom Operation - All Sizes Boom in raised position. Boom in lowered position. Unfolding & folding the CAUTION: To operate the boom: If working on steep terrain, please Spray Boom 1. Use the tractor remote controls to note the following: fold and unfold the spray boom.
  • Page 44 Chemical Mixing Sprayer Operation Accurately calculate the amount of chemical Unlock the Chem-E-Flush with the foot latch. Lower hopper into the filling position. Rotate the Pressure Control lever to "CHEM- required. HOPPER". Calculate Water & Adding Chemical To 2. For volume of mixture required c) Lower the hopper to filling position.
  • Page 45 Section 3 Chemical Mixing Open the Agitator valve. Open hopper lid & add chemical powder/liquid. Open the Transfer valve to transfer the mixture. Lift the hopper & lock it back into transport position. o) To transfer the rinse mixture to f) Open the Agitator valve.
  • Page 46 Chemical Mixing Sprayer Operation Connect Probe & Probe Rinse hoses. Turn the Suction Line Valve to "Flush" position. Open Probe valve to transfer mixture to spray tank. Close probe valve. 2. Chemical Probe d) Turn the Suction Line valve to h) Place the probe in the chemical and j) Close the Probe valve when the "Flush"...
  • Page 47 Section 3 Chemical Mixing Unclip the Micromatic fitting from its docking point. Turn the rotary selector to “Chem Hopper”. Enviro-transfer Kit Step 1 Step 2 Step 3 Unclip the Micromatic fitting from the Turn the rotary selector on the main Engage the PTO to start the main spray The Enviro-transfer kit is a volumetric docking fitting on the sprayer and clip...
  • Page 48 Chemical Mixing Sprayer Operation Unclip the Micromatic fitting from the Envirodrum. With the pump running, turn the two taps into the Watch the level closely - maximum fill is 50 litres. Turn the Chem-e-flush tap to introduce the Enviro-transfer position. chemical directly to tank (as shown).
  • Page 49 Section 3 Chemical Mixing A fresh water hose allows the Micromatic fittings Return the two taps to the normal spray position. Return the main rotary selector to the Turn-off the tap on the bottom to be flushed after use. “Spray” position. of the Chem-e-flush.
  • Page 50 Airbag Suspension Sprayer Operation Airbag suspension system. Unladen airbag ride height is pre-set to 220mm. Slacken the clamp on the vertical vertical rod. Check the Airbag Airbag Ride Height Airbag Pressure To lower (decrease pressure in) an airbag: Adjustment 1. Slacken the clamp on the vertical Suspension The ride height of the airbag is factory pre- valve rod, and...
  • Page 51 Dual Lines Section 3 Dual lines on the boom. Dual line valves at the rear of the sprayer. The BA7000 Manual. X20 Manual. Dual Lines 2. To increase the speed range available For the operation of dual lines, you for your sprayer by having the will need the refer to the BA7000/X20 second boom line cut in/out at a Controller booklet supplied with your...
  • Page 52 Operating Pointers Sprayer Operation Operating Methodology for Proceed to Spray Operating Pointers Broadacre Spraying Once the chemical mixture is in the While spraying, continually observe that: It is always preferable to spray travelling Travelling with the wind increases the tank, proceed to spray: 1.
  • Page 53: Sprayer Calibration

    Sprayer Calibration Section 4 Calibration Procedure XR & AI TeeJet Nozzle Chart Air-Mix & Turbodrop® Nozzle Chart 4.10 Calibration Work Sheet 4.12 Pegasus BT-POM 1212 - Rev 3...
  • Page 54 Calibration Procedure Sprayer Calibration Proper calibration considers all spraying variables. Rapid Check Flowmeter Calibration IMPORTANT: Applying the correct amount of chemical Proper calibration involves setting up to a crop is only possible if: the sprayer (nozzle selection, pressure, Procedure 1. It should be remembered that the speed), calculating chemical and water •...
  • Page 55 Section 4 Calibration Procedure For correct calibration, your flowmeter must be clean & accurate. Unscrew the the Rapid Check assembly. Wash any impurities out of the removable Unscrew the sensor. Place the Rapid Check unit in a detergent bath. turbine unit. Daily Check &...
  • Page 56 Calibration Procedure Sprayer Calibration Determine actual speed of travel. Buyers Guide - courtesy of Teejet. AI nozzle - courtesy of Teejet. Step 2 Step 3 Step 4 a) Use Your Manual's Chart Or Manufacturer’s Nozzle Chart. Determining the Actual Measure Swath Width Select Nozzle Type &...
  • Page 57 Section 4 Calibration Procedure L/min column on nozzle chart - courtesy of Teejet. Test the actual output of the nozzles. Step 5 Step 6 (Recommended) An alternative formula is: Fit the Selected Nozzles to Check Nozzle Accuracy & Nozzle Flow Rate (l/min) = the Boom Determine Nozzle Output Speed (km) x Nozzle Spacing (cm)
  • Page 58 Calibration Procedure Sprayer Calibration Step 7 Spray tip wear - courtesy of Teejet. f) Discard and replace any nozzle that deviates more than 10% from the Calculate Application Rate c) Collect and measure the volume of d) When the pressure is set to give a specified output (eg with a 0.5 l/min spray from one nozzle and adjust specified nozzle output (using a new...
  • Page 59 Section 4 Calibration Procedure +/- keys. Step 8 Step 9 b) In Manual mode - the Controller c) For land area covered, use the formula: application rate can be altered by: If tested application is not Add The Correct Amount Area Covered (ha) = i) Adjusting pressure up or down to satisfactory:...
  • Page 60 Calibration Procedure Sprayer Calibration Boom height - courtesy of Teejet. Step 10 Step 11 Adjust Boom Height Record All Data For Future Reference Boom height should be adjusted to suit the type of nozzle used, terrain and crop Record all your calibration data on the or soil being sprayed.
  • Page 61 XR & AI TeeJet Nozzle Chart Section 4 [ XR = Extended Range ] [ AI = Air Induction ] Litres/ha @ 500mm nozzle spacing Nozzle (filter) l/min 4km/h 5km/h 6km/h 7km/h 8km/h 10km/h 12km/h 16km/h 18km/h 20km/h 25km/h 30km/h 35km/h 0.23 69.0...
  • Page 62 Sprayer Calibration Air-Mix & Turbodrop Nozzle Chart ® Litres/ha @ 500mm nozzle spacing Nozzle l/min 5km/h 6km/h 7km/h 8km/h 10km/h 12km/h 16km/h 20km/h 25km/h 30km/h 35km/h 0,346 0,490 0,600 TDAM015 0,693 TD015 0,775 0,849 (Green) 0,917 0,980 1,039 1,095 0,462 0,653 0,800 TDAM02...
  • Page 63 Section 4 Air-Mix & Turbodrop Nozzle Chart ® Litres/ha @ 500mm nozzle spacing Nozzle l/min 5km/h 6km/h 7km/h 8km/h 10km/h 12km/h 16km/h 20km/h 25km/h 30km/h 35km/h 0,924 1,306 1,600 TDAM04 1,847 TD04 2,066 2,263 (Red) 2,444 2,612 2,771 2,921 1,155 1,633 2,000 TDAM05...
  • Page 64 Calibration Work Sheet Sprayer Calibration Step 1 Nozzle Flow Rate (l/min) If Tested Application is Not Satisfactory - Make Changes & Repeat Procedure Check the Sprayer is in Good Working Order Speed (km/hr) x Swath Width (m) x Application ................. Step 2 Rate (l/ha) ÷...
  • Page 65 Section 4 Calibration Work Sheet Step 1 Nozzle Flow Rate (l/min) If Tested Application is Not Satisfactory - Make Changes & Repeat Procedure Check the Sprayer is in Good Working Order Speed (km/hr) x Swath Width (m) x Application ................. Step 2 Rate (l/ha) ÷...
  • Page 66 Calibration Work Sheet Sprayer Calibration Step 1 Nozzle Flow Rate (l/min) If Tested Application is Not Satisfactory - Make Changes & Repeat Procedure Check the Sprayer is in Good Working Order Speed (km/hr) x Swath Width (m) x Application ................. Step 2 Rate (l/ha) ÷...
  • Page 67: Lubrication & Maintenance

    Lubrication & Maintenance Section 5 Greasing & Service Procedures Grease Point Diagrams Diaphragm Pumps Filters Diaphragms, Straps & Foam Markers Motor Valves Booms Airbag Suspension 5.11 Pegasus BT-POM 1212 - Rev 3...
  • Page 68 Greasing & Service Procedures Lubrication & Maintenance Greasing & Service Every 200 Hours or 6 Months 8. Grease tractor to sprayer PTO 11. Check pump air chamber pressure universal joints every 8 hours. on a regular basis. As a general - Whichever comes sooner Procedures guideline it should be 10%-20% of...
  • Page 69 Grease Point Diagrams Section 5 Chassis & PTO Grease Points Boom Grease Points Pegasus BT-POM 1212 - Rev 3...
  • Page 70 Diaphragm Pumps Lubrication & Maintenance Diaphragm Pump Daily after Use Every 50 Hours Every 250 hours or Every Season - Whichever Maintenance Check surge chamber pressure and 1. Flush pump with clean water. Comes Sooner adjust as follows: 2. Drain filters and clean. A high Annovi &...
  • Page 71 Section 5 Diaphragm Pumps Excessive Pre-Season Pump Storage and 8. Bypass line too small to carry full Diaphragm Failure Servicing Corrosion Protection capacity of pump. 9. In cold climates - frozen suction/ 1. Warm Climates If you have excessive diaphragm failure For thorough pre-season servicing - discharge lines or water remaining in If you operate in a warm climate with...
  • Page 72 Filters Lubrication & Maintenance Remove outer screw & bowl of suction filter. Remove & clean the filter element & components. Reassemble & tighten outer screw of suction filter. Regularly check and clean nozzle filters. Filter Maintenance Suction Filter Pressure Filters Nozzle Filters The suction filter should be cleaned The pressure filters should be cleaned...
  • Page 73 Diaphragms, Straps & Foam Markers Section 5 Remove & clean non-drip diaphragms regularly. Regularly check that tank straps are tight. Remove the Outback cabinet. Use an air hose clean out the cabinet area. Non-Drip Tank Straps Foam Marker Off-Season Storage Diaphragms Maintenance To prepare the foam marker for storage,...
  • Page 74 Foam Markers, Motor Valves Lubrication & Maintenance Regularly clean the air filter. Regularly clean the foam marker filter. 5-bank motor valves pictured. Air Cleaner Liquid Filter Electric Motor-Valve 4. Check with the chemical manufacturer to be sure chemicals Maintenance The air cleaner, located on the frame The liquid filter, located on the bottom being used are compatible with the as shown should be cleaned weekly.
  • Page 75 Booms Section 5 Boom Maintenance Every 50 Hours Maintenance Careful and regular maintenance will 4. Check wear of sliding shoes (D), 6. Grease the boom parellelogram lift & ensure good, long operational life. Carry out the following maintenance shown in figure 2 (above). suspension pivot points.
  • Page 76 Booms Lubrication & Maintenance Periodical Maintenance End of Season Maintenance 1. Check springs(A) [New SF only] and B) shown in figure 4 above; 1. Before storage clean all equipment thoroughly. replace them if flattened or damaged. 2. If necessary protect sprayer plumbing components with 2.
  • Page 77 Airbag Suspension Section 5 Airbag suspension system. Air chamber drain valve/tap. Air levelling valve with adjustable linkage. Trailing Arm Front Air Chamber Drain Adjustable Linkage Hinge Valve Assembly Linkage assembly illustration. The bush of the Trailing Arm Front Hinge The air chamber features a drain valve To assemble the adjustable linkage of the Note: To select the right or left hand assembly can be replaced when worn.
  • Page 78 5.12 Pegasus BT-POM 1212 - Rev 3...
  • Page 79: Trouble Shooting

    Trouble Shooting Section 6 Diaphragm Pump Problems General Sprayer Problems Hydraulic Pump Drive Problems Foam Marker Problems Airbag Suspension Problems Boom Problems Motor Valve Problems 6.10 Pegasus BT-POM 1212 - Rev 3...
  • Page 80 Diaphragm Pump Problems Trouble Shooting PROBLEM PROBABLE CAUSE REMEDY A Pump does not draw or deliver liquid. 1 One or more valves are not seating properly. 1 Clean valve seating. Pressure gauge fluctuates badly. 2 The pump is sucking in air through suction line. 2 Examine the suction hose and ensure it is firmly secured.
  • Page 81 Section 6 Diaphragm Pump Problems PROBLEM PROBABLE CAUSE REMEDY E Oil being discharged through delivery 1 One or more diaphragms split or ruptured. 1 Immediately drain oil from pump and flush to remove all spray residues from sump. Remove line or discoloured oil in sight glass of pump.
  • Page 82 General Sprayer Problems Trouble Shooting PROBLEM PROBABLE CAUSE REMEDY 1 No spray when turned on. 1 Filter on the inlet side of the pump blocked. 1 Dismantle, clean & re-assemble. 2 Faulty pump. 2 Change pump. 1 Air inlet to tank blocked. 1 Clean air vent.
  • Page 83 Hydraulic Pump Drive Problems Section 6 PROBLEM PROBABLE CAUSE REMEDY A Hydraulic system overheating 1 Refer to pump selection guide to determine 1 Improper hydraulic motor size. proper size for your system. 2 Close adjustment screw on side of hydraulic 2 Bypass adjustment screw set to bypass too motor to lessen the amount of bypassing oil.
  • Page 84 Foam Marker Problems Trouble Shooting PROBLEM PROBABLE CAUSE REMEDY A Marker doesn’t run at all 1 Harness plug not plugged in or 1 Check all wiring plugs and connections. 2 Circuit breaker popped or fuse blown. 2 Check breaker/fuse and reset/replace if necessary. B Air pump runs –...
  • Page 85 Foam Marker Problems Section 6 PROBLEM PROBABLE CAUSE REMEDY 1 Air On/Off solenoid valve doesn't operate. 1 Check for 12V to solenoid. If not, check for D Discharges almost all water - Air Flow Restricted electrical issues. If so, replace air ON/Off solenoid valve.
  • Page 86 Airbag Suspension Problems Trouble Shooting PROBLEM PROBABLE CAUSE REMEDY A Air compressor runs constantly. 1 Air leakage in the system. 1 Find the air leak. Test by using full air pressure and applying soapy water. Fix any air leaks. Use Loctite 569 on all air threads. B Airbags lose pressure (when left standing for 1 Air leakage in the system.
  • Page 87 Boom Problems Section 6 Problem: Problem: The boom unfolds halfway and then stops. The boom does not align when unfolding. Probable Cause: Probable Cause: Problem: Impurity in calibrated joint during assembly of 1. Ball joint of the unfolding cylinder not adjusted. cylinders.
  • Page 88 Motor Valve Problems Trouble Shooting PROBLEM PROBABLE CAUSE REMEDY A Boom line valve opens when it should be closed 1 Wiring incorrect. 1 Reverse polarity of valve by changing wires at the and closes when it should be open. valve cap. 1 Replace seat/hosetail and/or valve system if B Water leaks past valve when valve is shut.
  • Page 89 Assembly Drawings & Parts Listings Section 7 AR160/185 Pump AR250 Pump Liquid Control System Rotary Valves Liquid System Filling System 7.10 Valves - Transfer Kit 7.11 EnviroTransfer Kit - AR180/AR250 7.12 Chem E Flush Assembly 7.14 Filters 7.16 Lids, Venturis & Tank Rinse Jet 7.17 Foam Marker Components 7.18...
  • Page 90: Assembly Drawings & Parts Listings

    AR160/185 Pump Assembly Drawings & Parts Listings NOTE This drawing is for illustration purposes only. Please refer to the parts list. Pegasus BT-POM 1212 Rev 3...
  • Page 91 Section 7 AR160/185 Pump Part No Description Part No Description AR3040430 Ø 40 Elbow - AR 160 bp AR390290 Ø 29x3 O-ring AR3040440 Ø 50 Elbow - AR 185 bp AR380243 Washer - Geomet AR3040450 2” G Ring nut AR390315 Washer - Inox AR3040470 OR Ø...
  • Page 92: Ar250 Pump

    AR250 Pump Assembly Drawings & Parts Listings NOTE NOTE This drawing is for illustration purposes only. Please refer to the parts list. Pegasus BT-POM 1212 Rev 3...
  • Page 93 Section 7 AR250 Pump Part No Description Part No Description AR750870 ø 50 Hose tail AR750122 Piston 80mm AR750730 ø 60 Hose tail AR750420 Manifold AR750071 M12 x 70 Bolt AR160700 AR750200 Base plate AR160691 Pin circlip AR750740 74 x 3.53 O-Ring AR750140 Connecting rod AR750860...
  • Page 94: Liquid Control System

    Liquid Control System Assembly Drawings & Parts Listings Electric Pressure Dump Valve, Manual Pressure Relief Valve, Electric Regulating Valve (Servo) and Flowmeter for AR185 Pumps Manual Regulator-Dump Valve Assembly Pos Part No Description A471502 Complete Regulator A010005 Clip A471202.A32 Bypass Tail A4653920S Valve Motor A010003...
  • Page 95 Section 7 Liquid Control System Electric Pressure-Dump Valve, Electric Regulating Valve (Servo), Manual Pressure Relief Valve and Flowmeter for AR250/280 Pumps Dump Valve Dump Valve Parts Pos Part No Description Manual PRV A473001 Complete Valve A4653920S Motor { Repair Kit } A473011.550 Regulator Stem Kit A473001.A25 Tail/Seat A010003...
  • Page 96: Rotary Valves

    Rotary Valves Assembly Drawings & Parts Listings 2'' Rotary Valve 1¼'' Rotary Valve Part No: POL10424399 Part No: POL10405899. Seal Kit (5 pieces). Seal Kit (5 pieces). (Kit includes seals & O-rings, but (Kit includes seals & O-rings, but not the ball, body or fittings). not the ball, body or fittings).
  • Page 97: Liquid System

    Liquid System Section 7 Boom Shut-Off Valves, Pressure Gauge & Control Valve/Taps Boom Shut-Off Valve (each) Pos Part No Description A463011ST Complete Valve Boom Shut-Off Valves A4653920S Motor A473011.550 Regulator Stem Kit A473001.125 Tail/Seat A010003 Clip [Internal] Shut-Off Taps - Tank Rinse, Probe Rinse & Agitators Pressure Gauge: L-G 1611 Pos Part No Description...
  • Page 98: Filling System

    Filling System Assembly Drawings & Parts Listings Filter Orion Filling Flow-meter Pos Part No Description A4622BA61717 Orion Complete Non-Return Valve 2" Pos Part No Description Filling System with Camlok A333072 Filter Complete A333000.050 Main Seal O-Ring Pos Part No Description A317003.030 Screen - internal BP-112A Valve complete...
  • Page 99: Valves - Transfer Kit

    Valves - Transfer Kit Section 7 Pos Part No Description A454137 Valve Complete Drain Valve 2" A454236.050 Tap Handle A-EL200 Tail Pos Part No Description Spray/Off/Flush Valve 1½" A454236 Valve Complete A454236.050 Tap Handle Pos Part No Description Boom Flushing Tap BALL12F2M Valve Complete BJHB050/075-90 Elbow...
  • Page 100 Enviro Transfer Kit - AR180/250 Assembly Drawings & Parts Listings Part No Description Part No: L-H9366/250 L-H9562 COUPLER 3 PIN VITON A-A1010 HOSEBARB 1" THREAD (M) X 1" HOSE TR1HC HOSE CLAMP 25mm HEP25 SUCTION HOSE 25mm A200010 FLY NUT 1" A116425 ELBOW 0.25 FOR FLY NUT AG10041...
  • Page 101 Section 7 PLEASE TURN TO THE NEXT PAGE Pegasus BT-POM 1212 Rev 3 7.13...
  • Page 102: Chem E Flush Assembly

    Chem E Flush Assembly Assembly Drawings & Parts Listings 60 litre ChemeFlush Drop Down Assembly Part No: L-H9351A Part No: L-H9355A Pegasus BT-POM 1212 Rev 3 7.14...
  • Page 103 Chem E Flush Assembly Section 7 Pos Part No Description Pos Part No Description L-H9351A 60 litre ChemeFlush TR12HC HOSE CLAMP 20MM 1/2” WORM DRIVE UP-105AB CHEM-E-FLUSH MOUNTING BRKT SERIES 2 A106425 TAIL 1” TO 25MM UP-116 NOZZLE 8.5 VENTURI CHEM E PLUS A106640 TAIL 1 1/2”...
  • Page 104: Filters

    Filters Assembly Drawings & Parts Listings Suction Filter Pos Part No Description A316 173 Filter Complete A316000.050 Main Seal A316003.030 Screen - internal A316300.60 Screen O-Rings Suction Filter (shown above on sprayer) Pressure Filter Pos Part No Description A32621135 Filter Complete AG10090 Main Seal A3260035.030 Screen - internal...
  • Page 105: Lids, Venturis & Tank Rinse Jet

    Lids, Venturis & Tank Rinse Jet Section 7 Tank Lid Basket Pos Part No Description Part No: A300.0134 Tank Lid & A356060 Lid Complete Basket A356660.02 Seal Ring Lid on top of tank, basket inside. Foam & Rinse Tank Lids Breather Foam &...
  • Page 106: Foam Marker Components

    Foam Marker Components Assembly Drawings & Parts Listings Foam Boot & Foam Tubing Foam Boot, Foam Tubing & Salamander Boost Foam Tube Kits Note: Standard length 20m coil, see Part # 1 (at left) Pos Part No Description HCVT20 Foam Tube RHAA120 Foam Boot Complete RHSJ000...
  • Page 107 Foam Marker - Outback 10 Section 7 [Not shown] 1 Directional 2 Foam Chamber 3 Gauge 4 AR Pump Solenoid Valve Assembly P/N: RHGF60 P/N: RHFU001 P/N: AA144P-1-3 P/N: LST075-HB (0-100 kpa) 5 Cab Mounted Switch Box 6 Check Valve 7 Liquid Pump Assembly 8 Liquid Filter P/N: RHAB371...
  • Page 108: Boom Fittings

    Boom Fittings Assembly Drawings & Parts Listings Boom Fittings 1 Boom Tube: a) 2-hole Part No: GB550200500 b) 3-hole Part No: GB550300500 c) 4-hole Part No: GB550400500 d) 5-hole Part No: GB550500500 e) 6-hole Part No: GB550600500 [not shown] f) 7-hole Part No: GB550700500 2 See page 7.11 Boom flush tap...
  • Page 109: Nozzles & Nozzle Bodies

    Nozzles & Nozzle Bodies Section 7 Triplex Nozzle Complete Triplex Nozzle Body Part No: QJ363B-¼-NYB (does not include caps & seals) Cap & Seal 1 Cap & Seal for XR Teejets Part No: 25612-*3-NYR Cap & Seal 2 Cap & Seal for AI Teejets Part No: 25298-*3-NYR Nozzle Jet Selection Pos Part No...
  • Page 110: Chassis, Tank & Wheels

    Chassis, Tank & Wheels Assembly Drawings & Parts Listings Pegasus BT-POM 1212 Rev 3 7.22...
  • Page 111 Section 7 Chassis, Tank & Wheels Part No Description Part No Description BP-700A CHASSIS PEGASUS 4000/5000LT P30CAP CAP 30LT FM TANK C/W O RING BP-700B CHASSIS PEGASUS (6000LT only) A356060 LID HINGED 180 DEGREE 455MM BP-700A-1 PEGASUS DRAWBAR 4000/5000LT A300130...
  • Page 112: Axles & Stub Axles

    Axles & Stub Axles Assembly Drawings & Parts Listings PART NO: BP-509D PEGASUS 4000/5000L FIXED AXLE 8 STUD PART NO: BP-545A STUB AXLE Part No Description Part No Description BP-545A STUB AXLE 90mm 8/275 PCD BP-532-1 STUB AXLE 90SQ x 538 LONG...
  • Page 113 Section 7 Axles & Stub Axles PART NO: BP-509E PEGASUS 4000/5000L AIRRIDE FIXED AXLE 8 STUD PART NO: BP-545A STUB AXLE Part No Description Part No Description BP-545A STUB AXLE 90mm 8/275 PCD BP-532-1 STUB AXLE 90SQ x 538 LONG...
  • Page 114 Axles & Stub Axles Assembly Drawings & Parts Listings PART NO: BP-509F PEGASUS 6000L AJUSTABLE AIRRIDE AXLE 10 STUD PART NO: BP-532 STUB AXLE Part No Description Part No Description BP-532 STUB AXLE 90SQ 10/335PCD BP-532-1A STUB AXLE 90SQ x 390 LONG MT10013 SPEED SENSOR MOUNTING BRACKET BP-532-2...
  • Page 115 Section 7 Axles & Stub Axles PART NO: BP-509G PEGASUS 6000L AIRRIDE FIXED AXLE 10 STUD PART NO: BP-532A STUB AXLE Part No Description Part No Description BP-532A STUB AXLE 90mm 10/335PCD 538LG BP-532-1 STUB AXLE 90SQ x 538 LONG MT10013 SPEED SENSOR MOUNTING BRACKET BP-532-2...
  • Page 116 Axles & Stub Axles Assembly Drawings & Parts Listings PART NO: BP-509H PEGASUS 4000/5000L AJUSTABLE AIRRIDE AXLE 8 STUD PART NO: BP-545A STUB AXLE Part No Description Part No Description BP-545A STUB AXLE 90mm 8/275 PCD BP-532-1 STUB AXLE 90SQ x 538 LONG...
  • Page 117: Compressor & Air Tank

    Compressor & Air Tank Section 7 Compressor Pos Part No Description BP-625 Compressor Complete 1 BP-625KIT BP-624 Coupler [internal] Compressor Air Tank Pos Part No Description FM-NRV Non-return Valve BP-622 Air Relief Valve Ass BALL14MF2M Exhaust/drain tap TFEL144MF Brass Elbow BP-627 Pilot Operated Relief Assembly...
  • Page 118: Air Ride Suspension System

    Air Ride Suspension System Assembly Drawings & Parts Listings Part No Description BP-625 AIR COMPRESSOR PTO DRIVE FM-NRV NON RETURN VALVE BP-627 UNLOADER KIT L-G1420 GAUGE BP-620 AIR TANK RH-69539 LEVELLING VALVE BP-610 RELIEF VALVE BP-608B AIR BAG SPRING BALL14MF2M BALL VALVE DRAIN TFEL1414MF BRAS ELBOW ¼"...
  • Page 119: Electrical Wiring

    Electrical Wiring Section 7 MT9000 / 3 PIN BALL VALVES WIRING CONFIGURATION FOR 24 PIN MT9000 BULKHEAD LOOM 4/12/2003 ALL WIRE 3mm 3 PIN YELLOW 2.5mm YELLOW 2.5mm SPEED YELLOW 2.5mm 3 PIN YELLOW pulse 3 PIN GREEN 2.5mm GREEN 2.5mm SPEED WHITE GREEN 2.5mm...
  • Page 120 Electrical Wiring Assembly Drawings & Parts Listings MT90LOOM/6. marker. Connects to MT90LOOM/1. MT90LOOM/1 Main loom from rear of tractor to the sprayer, MT90LOOM/2 MT90LOOM/3 connects to control valves, foam marker etc Main loom from Spray controller to the rear of the Extension loom that runs from front of sprayer, &...
  • Page 121 Plumbing Diagram AR180 Section 7 Pegasus BT-POM 1212 Rev 3 7.33...
  • Page 122 Plumbing Diagram AR250/280 Assembly Drawings & Parts Listings Pegasus BT-POM 1212 Rev 3 7.34...
  • Page 123 Hydraulic Plumbing Diagram - 24m Standard Fold Section 7 QUICK CONNECT 1/2” BSPP FOLD R81 - 08M COUPLERS Pegasus BT-POM 1212 Rev 3 7.35...
  • Page 124 Hydraulic Plumbing Diagram - 24m OWF Assembly Drawings & Parts Listings QUICK CONNECT 1/2” BSPP FOLD R81 - 08M COUPLERS Pegasus BT-POM 1212 Rev 3 7.36...
  • Page 125 Hydraulic Plumbing Diagram Section 7 - 24m Gvar QUICK CONNECT 1/2” BSPP R81 - 08M COUPLERS TO HYDRAULIC LIFT (refer separate lift drawing) Pegasus BT-POM 1212 Rev 3 7.37...
  • Page 126 Hydraulic Plumbing Diagram - 24m Gvar & OWF Assembly Drawings & Parts Listings QUICK CONNECT 1/2” BSPP R81 - 08M COUPLERS TO HYDRAULIC LIFT (refer separate lift drawing) Pegasus BT-POM 1212 Rev 3 7.38...
  • Page 127 Hydraulic Plumbing Diagram Section 7 - 28m Standard Fold QUICK CONNECT 1/2” BSPP FOLD R81 - 08M COUPLERS Pegasus BT-POM 1212 Rev 3 7.39...
  • Page 128 Hydraulic Plumbing Diagram - 28m OWF Assembly Drawings & Parts Listings QUICK CONNECT 1/2” BSPP FOLD R81 - 08M COUPLERS Pegasus BT-POM 1212 Rev 3 7.40...
  • Page 129 Hydraulic Plumbing Diagram Section 7 - 28m Gvar QUICK CONNECT 1/2” BSPP R81 - 08M COUPLERS TO HYDRAULIC LIFT (refer separate lift drawing) Pegasus BT-POM 1212 Rev 3 7.41...
  • Page 130 Hydraulic Plumbing Diagram - 28m Gvar & OWF Assembly Drawings & Parts Listings QUICK CONNECT 1/2” BSPP R81 - 08M COUPLERS TO HYDRAULIC LIFT (refer separate lift drawing) Pegasus BT-POM 1212 Rev 3 7.42...
  • Page 131 Hydraulic Plumbing Diagram Section 7 - 30m Standard Fold QUICK CONNECT 1/2” BSPP FOLD R81 - 08M COUPLERS Pegasus BT-POM 1212 Rev 3 7.43...
  • Page 132 Hydraulic Plumbing Diagram - 30m OWF Assembly Drawings & Parts Listings QUICK CONNECT 1/2” BSPP FOLD R81 - 08M COUPLERS Pegasus BT-POM 1212 Rev 3 7.44...
  • Page 133 Hydraulic Plumbing Diagram Section 7 - 30m Gvar QUICK CONNECT 1/2” BSPP R81 - 08M COUPLERS TO HYDRAULIC LIFT (refer separate lift drawing) Pegasus BT-POM 1212 Rev 3 7.45...
  • Page 134 Hydraulic Plumbing Diagram - 30m Gvar & OWF Assembly Drawings & Parts Listings QUICK CONNECT 1/2” BSPP R81 - 08M COUPLERS TO HYDRAULIC LIFT (refer separate lift drawing) Pegasus BT-POM 1212 Rev 3 7.46...
  • Page 135 Hydraulic Plumbing Diagram Section 7 - 33/36m Standard Fold QUICK CONNECT 1/2” BSPP FOLD R81 - 08M COUPLERS Pegasus BT-POM 1212 Rev 3 7.47...
  • Page 136 Hydraulic Plumbing Diagram - 33/36m Gvar Assembly Drawings & Parts Listings QUICK CONNECT 1/2” BSPP R81 - 08M COUPLERS TO HYDRAULIC LIFT (refer separate lift drawing) Pegasus BT-POM 1212 Rev 3 7.48...
  • Page 137 Hydraulic Plumbing Diagram Section 7 - 33/36m Gvar & OWF QUICK CONNECT 1/2” BSPP R81 - 08M Hydraulic Manifold Notes: COUPLERS • Use MP-631 5 Function Manifold for Factory fit • Add MP-628 Single station to MP-630 manifold for Retro-fit TO HYDRAULIC LIFT (refer separate lift drawing) Pegasus BT-POM 1212 Rev 3...
  • Page 138 GBCOMPL-24/28CA - Centre Section 24/28m Assembly Drawings & Parts Listings Pegasus BT-POM 1212 Rev 3 7.50...
  • Page 139 GBCOMPL-24/28CA - Centre Section 24/28m Section 7 Part No Description Part No Description GB550500500 5 HOLE SPRAY RAIL GBBG027334 24/28m CENTRE SECTION GBBG016908 Inner Fold Ram 24/28m GB999900467 WARNING LABEL PLATE KIT GB570500008Z 1/4” NIPPLE 0.8 ORIFICE GB201800065V WARNING PLATE GBBG50243113 COPPER WASHER GB50050004Z...
  • Page 140 GBCOMPL-24/28CA - Centre Section 24/28m Assembly Drawings & Parts Listings Pegasus BT-POM 1212 Rev 3 7.52...
  • Page 141 GBCOMPL-24/28CA - Centre Section 24/28m Section 7 Part No Description Part No Description GB382000023V MAIN LEVELLING FRAME GB900106010Z M6 x 20 BOLT (ZINC) GB993806001V TIE ROD ASSY. GB997000018 LOCK RAM ASSY COMPLETE GB500400019Z M24 WASHER (ZINC) GB702550023V LOCKING RAM GB905400024 M24 NYLOC NUT (ZINC) GB996000179 SEAL KIT...
  • Page 142 GBCOMPL-245-LH or RH - Boom Non Gvar 24m 24/28m Assembly Drawings & Parts Listings Pegasus BT-POM 1212 Rev 3 7.54...
  • Page 143 GBCOMPL-245-LH or RH - Boom Non Gvar 24m Section 7 Part No Description Part No Description GB022400030V INNER BOOM ARM R/H GB500400019Z WASHER GB022400031V INNER BOOM ARM L/H GB950130030 BOOM END CAP GB022400050V OUTER BOOM ARM R/H GB950200004 BOOM STOPPER 20MM GB022400051V OUTER BOOM ARM L/H GB950200001...
  • Page 144 GBCOMPL-245-LH or RH - Boom Gvar 24m Assembly Drawings & Parts Listings Pegasus BT-POM 1212 Rev 3 7.56...
  • Page 145 GBCOMPL-245-LH or RH - Boom Gvar 24m Section 7 Part No Description Part No Description GBBG026447 G-VAR PIVOT ARM R/H V2 GB500100086 GBBG026449 G-VAR PIVOT ARM L/H V2 GB500200029Z SPACER GBBG026378 G-VAR INNER ARM R/H V2 GB022800037V LINK ARM ROD GBBG026379 G-VAR INNER ARM L/H V2 GB022800036V...
  • Page 146 GBCOMPL-285-LH or RH - Boom Non Gvar 28m Assembly Drawings & Parts Listings Pegasus BT-POM 1212 Rev 3 7.58...
  • Page 147 GBCOMPL-285-LH or RH - Boom Non Gvar 28m Section 7 Part No Description Part No Description GB950200001 RUBBER STOPPER 30mm GBBG002915 INNER BOOM ARM R/H GBBG002916 INNER BOOM ARM L/H GB907108024Z M8 X 24mm WASHER GB022400050V OUTER BOOM ARM R/H GB905400008 M8 NYLOC NUT (ZINC) GB022400051V...
  • Page 148 GBCOMPL-285GV-LH or RH - Boom Gvar 28m Assembly Drawings & Parts Listings Pegasus BT-POM 1212 Rev 3 7.60...
  • Page 149 GBCOMPL-285GV-LH or RH - Boom Gvar 28m Section 7 Part No Description Part No Description GB500100111Z BREAKAWAY SHAFT GBBG026447 G-VAR PIVOT ARM R/H V2 GBBG026449 G-VAR PIVOT ARM L/H V2 GB919900023Z BREAKAWAY SPRING GBBG026315 G-VAR INNER ARM R/H V2 GB500400019Z WASHER GBBG026316 G-VAR INNER ARM L/H V2...
  • Page 150 GBCOMPL-30C - Centre Section 30m Assembly Drawings & Parts Listings Pegasus BT-POM 1212 Rev 3 7.62...
  • Page 151 Section 7 GBCOMPL-30C - Centre Section 30m Part No Description Part No Description GBBG001108 30m CENTRE SECTION GB905300006 M6 NYLOC NUT (ZINC) GB703570018V HYDRAULIC RAM A425130 2 PIECE RAIL CLAMP GB500300032V M30 SPACER NUT GB904506040X M6 x 40mm SCREW STAINLESS GBBG001752 M30 BALL JOINT GB905400006X...
  • Page 152 GBCOMPL-30C - Centre Section 30m Assembly Drawings & Parts Listings Pegasus BT-POM 1212 Rev 3 7.64...
  • Page 153 Section 7 GBCOMPL-30C - Centre Section 30m Part No Description Part No Description GB500700069 STRAINER WIRE GB382000050V SELF LEVELLING FRAME GB993806001V TIE ROD ASSY. CABLE TIE GB950300004 FLEXIBLE BUSH GB905415014 M14 NUT FINE THREAD (1.5) GB500400019Z M24 WASHER GB900314060Z M14 x 60mm BOLT (ZINC) 8.8 GB905400024 M24 NYLOC NUT GB919800061Z...
  • Page 154 Assembly Drawings & Parts Listings GBCOMPL-305-LHA or RHA - Boom Non Gvar & Gvar 30m Pegasus BT-POM 1212 Rev 3 7.66...
  • Page 155 Section 7 GBCOMPL-305-LHA or RHA - Boom Non Gvar & Gvar 30m Part No Description Part No Description GB900124050Z M24 BOLT GBBG026414 INNER PIVOT R/H V2 GBBG026415 INNER PIVOT L/H V2 GB905200024Z M24 PLAIN NUT (ZINC) GBBG025150 INNER BOOM ARM R/H V2 GB500200049 CAP WASHER GBBG025151...
  • Page 156 GB990902501 - Skid Kit Pair 24m Assembly Drawings & Parts Listings Part No Description GG919900030V GG501100008V GG501100009V GG500500003Z Pegasus BT-POM 1212 Rev 3 7.68...
  • Page 157 GBBG016255 - Skid Kit Pair 28/30m Section 7 Part No Description BG016220 BG016280 BG016282 GG500500002Z GG905400010 Pegasus BT-POM 1212 Rev 3 7.69...
  • Page 158 AB19100-AA - 33/36m - Centre Section/Hanger V2 Assembly Drawings & Parts Listings Pegasus BT-POM 1212 Rev 3 7.70...
  • Page 159 AB19100-AA - 33/36m - Centre Section/Hanger V2 Section 7 Pos Part No Description Pos Part No Description AB19199 CYLINDER INNER FOLD 3” X 16” EZFIT AB191-100 SELF LEVELLER ADJUSTER AB191-101 SELF LEVELLER FIXED ARM AB19199-M ROD END MALE INNER FOLD CYLINDER AB19101 CENTRE SECTION HANGER AB19199-F...
  • Page 160 Complete Left/Right Boom Arm 33/36m Assembly Drawings & Parts Listings PART NUMBER DESCRIPTION AB19100-BR-33 33M RIGHTHAND BOOM ARM COMPLETE AB19100-BR-36 36M RIGHTHAND BOOM ARM COMPLETE AB19100-BL-33 33M LEFTHAND BOOM ARM COMPLETE AB19100-BL-36 36M LEFTHAND BOOM ARM COMPLETE Pegasus BT-POM 1212 Rev 3 7.72...
  • Page 161 Complete Left/Right Boom Arm 33/36m Section 7 Part No Description Part No Description M20X100BOLT M20 X 100 HEX HEAD BOLT HT ZP AB19107R FIRST ARM R.H. 33/36M AB19107L FIRST ARM L.H. 33/36M M20NNUT M20 NYLOC NUT HT ZP AB19100-A-2 FIXED WINGTIP ADJUSTMENT M20HNUT M20 HALF NUT ZP AB19100-A-3...
  • Page 162 Complete Left/Right Boom Arm 33/36m Assembly Drawings & Parts Listings PART NUMBER DESCRIPTION AB19100-BR-33 33M RIGHTHAND BOOM ARM COMPLETE AB19100-BR-36 36M RIGHTHAND BOOM ARM COMPLETE AB19100-BL-33 33M LEFTHAND BOOM ARM COMPLETE AB19100-BL-36 36M LEFTHAND BOOM ARM COMPLETE Pegasus BT-POM 1212 Rev 3 7.74...
  • Page 163 Complete Left/Right Boom Arm 33/36m Section 7 Part No Description Part No Description M10FWASHER M10 FLAT WASHER ZP AB19109AL BOOM ARM OUTER LH 36M AB19109AR BOOM ARM OUTER RH 36M M6GNIPPLE M6 GREASE NIPPLE AB19110L BOOM ARM OUTER LH 33M AB19110R BOOM ARM OUTER LH 33M NOTE...
  • Page 164 AB19196 - 33/36m - Skid Complete Single Assembly Drawings & Parts Listings Part No Description AB19196-1 SKID SET 3 PIECE AB19196-2 SKID MOUNT 36M BOOM FEMALE AB19196-3 SKID MOUNT SHAFT AB191 BOOM AB19196-4 COLLAR DIA 30MM AB19196-6 SKID LEAF CLAMP M12X55 M12 X 55 SET SCREW HT ZP M12NNUT...
  • Page 168 CROPLANDS AUSTRALIA NEW ZEALAND Croplands Equipment Pty Ltd Croplands Equipment Ltd ACN 006 450 184 PO Box 2004, Stortford Bridge, Hastings 4120 PO Box 2441 Dry Creek Location: 50 Cavan Road 1422 Omahu Road, Dry Creek SA 5094 Hastings 4120...

This manual is also suitable for:

Pegasus 5000Pegasus 6000

Table of Contents