Starspace SKY-029 Instruction Manual

IN S T R U C T I O N M A NU A L
ASSEMBLY GUIDE
Congratulations, you are now the owner of a
brand new STARSPACE chair!
Following this assembly guide, you will
find a quick start guide to assemble your
STARSPACE chair. We highly recommend
checking out our Assembly Videos as well for
even more detailed and visual instructions.
If you run into any difficulty during the
a s s e m b l y , r e m e m b e r t o c h e c k o u t t h e
Assembly Video to see if you've missed
anything. If you're unable to resolve your
problems, drop us an email as well and our
support team will assist you.
PACKAGE LIST
[A] [G] [K]
Upper
Adjuster Covers
Casters *5 Bolts M8*25mm *16
[B] [G1] [L]
Star Base *1 Bolts M5*12mm *4
[C] [G2] [M]
Lower
Adjuster Covers
Gas Lift *1 Plastic Covers *4
[D] [H] [N]
Gas Lift Cover *1 Back Cushion *1
[E] [I]
Seat Plate *1 Head Pillow *1
[F] [J]
Seat Cushion *1 Back Pillow *1
Scan this QR Code to
STARSPACE CHAIR watch our assembly
video for the chair.
SUBSCRIBE
MODEL: SKY-029
ASSEMBLY INSTRUCTION
Make sure all bolts and screws are fully tightened before
CAUTION
using chair. Lubricate all moving parts and tighten all bolts/
screws every 6 month or whenever needed.
S T E P
Turn the Star Base(B) upside down,
then press the Casters(A) into
the holes at the end of each base
leg, insert the Gas Lift(C) into the
center hole of the Star Base, the
Gas Lift Cover(D) should be placed
over the Lift.
S T E P
Attach two Arms(N) and the Seat
*2
Plate(E) to the Seat Cushion(F)
with twelve Bolts M8*25mm(G),
using the Wrench(L).
NOTE
Arm rests are labeled with an "L" (left)
Wrench *1
or "R" (right) to show which sides they
should be placed on.
Make sure that the front of the seat plate
is facing the front of the Seat Cushion
*2
S T E P
Connect Back Cushion(H) and
Arms *2
Seat Cushion(F) with four Bolts
M8*25mm(G), using the Wrench(L),
install the back pillow(J) and head
pillow(I).
NOTE
Tight bolts to 50% at the first, after all
bolts were installed, tight all bolts to
100%.
Before you get started, a few pointers:
Having a friend to help
makes assembly extra-easy
1
[D]
[C]
[A]
[G]
2
[E]
3
[L]
[I]
[G]
[H]
[J]
[G]
[F]
Mind the important Contact us if you have
safety information any issues
S T E P 4
Attach two Upper Adjust covers
and Lower Adjuster cover with
four Bolts M5*12mm, using the
wrench(L), and press four Plastic
C o v e r s ( G 2 ) t o b o t h s i d e s o f
adjusters.
[B] [G2]
S T E P 5
Turn the Seat Cushion upright
and align the center hole of the
seat plate over the lift, then push
the seat cushion down onto the
lift firmly until the connection is
[N]
secure.
[F]
INSTRUCTIONS FOR USE
[L]
1
Seat Height:Paddle-shaped
lever on the right side
While taking your weight off
chair, lift lever up.
While seated, lift lever up.
At the proper height, your feet should rest flat on the floor.
CONTACT US
>>>
www.starspacechair.com
[L]
[G2]
[G1]
[G1]
+1 628-222-2513
service@starspacechair.com