Related Manuals for Edwards E2M175S
Summary of Contents for Edwards E2M175S
- Page 1 A366-99-840 Issue C Original Instructions E2M175S and E2M275S Rotary Pump Service Kits Description Item Number Clean and Overhaul Kit A366-01-131 Blade Kit for E2M175S A366-01-134 Blade Kit for E2M275S A367-01-134...
- Page 2 Never allow unqualified personnel to attempt to remove or replace any part of the pump. If you have any doubts about the servicing procedures or the products capabilities please contact Edwards. Before returning any equipment to Edwards for repair please follow the Edwards HS1 procedure and complete an HS2 declaration form to warn of any substances used or produced in the equipment that can be dangerous.
-
Page 3: Table Of Contents
E2M175S Blade Kit items ....................4 E2M275S Blade Kit items ....................4 Trademark credits Viton™ is a trademark of DuPont Performance Elastomers L.L.C. © Edwards Limited 2008. All rights reserved. Page i Edwards and the Edwards logo are trademarks of Edwards Limited. - Page 4 A366-99-840 Issue C This page has been intentionally left blank. Page ii © Edwards Limited 2008. All rights reserved. Edwards and the Edwards logo are trademarks of Edwards Limited.
-
Page 5: Introduction
E2M275S. These items are shown in Figures and 7. Instructions for the use of the Blade Kits are given in Section © Edwards Limited 2008. All rights reserved. Page 1 Edwards and the Edwards logo are trademarks of Edwards Limited. -
Page 6: Kit Parts
LV exhaust valve rubber Filter head gasket Ballast gasket Ballast gasket Valve body gasket Exhaust gasket End plate gasket Body gasket Page 2 © Edwards Limited 2008. All rights reserved. Edwards and the Edwards logo are trademarks of Edwards Limited. - Page 7 E2M275S only Knitmesh gasket E1M175S only Knitmesh gasket E2M275S only Body nut Exhaust warning label Inlet valve assembly item: see Figure © Edwards Limited 2008. All rights reserved. Page 3 Edwards and the Edwards logo are trademarks of Edwards Limited.
-
Page 8: Parts In The Blade Kits
Oil pump blade Table 3 - E2M275S Blade Kit items Illustration Quantity Description Item supplied HV blade LV blade Oil pump blade Page 4 © Edwards Limited 2008. All rights reserved. Edwards and the Edwards logo are trademarks of Edwards Limited. -
Page 9: Kit Items For Main Oil Box Sub-Assembly
A366-99-840 Issue C Figure 1 - Kit items for main oil box sub-assembly © Edwards Limited 2008. All rights reserved. Page 5 Edwards and the Edwards logo are trademarks of Edwards Limited. -
Page 10: Kit Items For Inlet Valve Sub-Assembly
Figure 2 - Kit items for inlet valve sub-assembly... -
Page 11: Kit Items For Oil Box End-Plate And Oil Filter Sub-Assembly
Figure 3 - Kit items for oil box end-plate and oil filter sub-assembly... -
Page 12: Kit Items For Gas Ballast Valve Sub-Assembly
Figure 4 - Kit items for gas ballast valve sub-assembly... -
Page 13: Kit Items For Oil Distributor Sub-Assembly
A366-99-840 Issue C Figure 5 - Kit items for oil distributor sub-assembly © Edwards Limited 2008. All rights reserved. Page 9 Edwards and the Edwards logo are trademarks of Edwards Limited. -
Page 14: Kit Items For Hv Stator Sub-Assembly
Figure 6 - Kit items for HV stator sub-assembly Supplied separately in the appropriate Blade Kit... -
Page 15: Kit Items For Lv Stator Sub-Assembly
Figure 7 - Kit items for LV stator sub-assembly Supplied separately in the appropriate Blade Kit... -
Page 16: How To Use The Kits
If this does not happen, refer to the pump instruction manual. 9. Open the gas ballast valve and operate the rotary pump for at least 1 hour. Page 12 © Edwards Limited 2008. All rights reserved. Edwards and the Edwards logo are trademarks of Edwards Limited.