Vertiv NetSure 7100 Series Installation And User Manual
Supervision module for distribution unit plus
Hide thumbs
Also See for NetSure 7100 Series:
- Installation manual (222 pages) ,
- Quick start manual (130 pages) ,
- User manual (106 pages)
Related Manuals for Vertiv NetSure 7100 Series
Summary of Contents for Vertiv NetSure 7100 Series
- Page 1 NetSure™ SM-DU+ Supervision Module for Distribution Unit Plus Installation and User Manual Specification Number: 10010507 Model Number: SM-DU+...
- Page 2 Vertiv™ NetSure™ Supervision Module for Distribution Unit Plus Installation and User Manual The information contained in this document is subject to change without notice and may not be suitable for all applications. While every precaution has been taken to ensure the accuracy and completeness of this document, Vertiv assumes no responsibility and disclaims all liability for damages resulting from use of this information or for any errors or omissions.
-
Page 3: Table Of Contents
Vertiv™ NetSure™ Supervision Module for Distribution Unit Plus Installation and User Manual TABLE OF CONTENTS Admonishments Used in this Document ......................... iv Important Safety Instructions ............................. v Static Warning ..................................vi 1 Introduction ..................................1 1.1 Overview ......................................................... 1 1.2 Technical Specifications ................................................. 1 2 Switch Settings .................................. -
Page 4: Admonishments Used In This Document
Vertiv™ NetSure™ Supervision Module for Distribution Unit Plus Installation and User Manual Admonishments Used in this Document will likely DANGER! Warns of a hazard the reader be exposed to that will result in death or serious injury if not avoided. (ANSI, OSHA) -
Page 5: Important Safety Instructions
Vertiv™ NetSure™ Supervision Module for Distribution Unit Plus Installation and User Manual Important Safety Instructions Safety Admonishments Definitions Definitions of the safety admonishments used in this document are listed under “Admonishments Used in this Document” on page iv. General Safety DANGER! YOU MUST FOLLOW APPROVED SAFETY PROCEDURES. -
Page 6: Static Warning
Vertiv™ NetSure™ Supervision Module for Distribution Unit Plus Installation and User Manual Static Warning This equipment contains static sensitive components. The warnings listed below must be observed to prevent damage to these components. Disregarding any of these warnings may result in personal injury or damage to the equipment. -
Page 7: Introduction
1.1 Overview This assembly consists of a Vertiv™ NetSure™ SM-DU+ enclosed in a sheet metal housing. This assembly is used in applications where the NetSure™ SM-DU+ is mounted external to a power system equipped with an NCU controller. The NetSure™ SM-DU+ assembly is used to connect load shunts and fuse alarm signals to the NCU controller. - Page 8 Vertiv™ NetSure™ Supervision Module for Distribution Unit Plus Installation and User Manual Figure 1.2 Dimensions 10.00 4.76 Bottom 2.57 Left Side Front Right Side 9.43 Diameter 0.14” (4-places) 3.86 Notes: 1. All dimensions are in inches, unless otherwise specified.
-
Page 9: Switch Settings
2 Switch Settings 2.1 General The Vertiv™ NetSure™ SM-DU+ assembly uses two (2) 8-bit switches for parameter settings (SW1 and SW2). Refer to Figure 2.1 for SW1 and SW2 locations. Refer to Table 2.1 for SW1 and SW2 settings. Perform the following procedure to make switch setting adjustments. - Page 10 Vertiv™ NetSure™ Supervision Module for Distribution Unit Plus Installation and User Manual Figure 2.1 NetSure™ SM-DU+ Assembly Switch Locations Note that these ports are not used in this application, refer to below image for customer connections terminal blocks location. See also Figure 4.2.
- Page 11 Vertiv™ NetSure™ Supervision Module for Distribution Unit Plus Installation and User Manual Table 2.1 Vertiv™ NetSure™ SM-DU+ Switch Settings DIP Switch SW1 HW/S Shunt Reserved Shunt Voltage Current Description of Status Shunt parameter is set through DIP switch. Shunt parameter is set through software (note 1).
-
Page 12: Installation
Vertiv™ NetSure™ Supervision Module for Distribution Unit Plus Installation and User Manual 3 Installation 3.1 Mounting The Vertiv™ NetSure™ SM-DU+ assembly provides mounting holes in each corner. Refer to Figure 1.2 for location and dimensions. 4 Electrical Connections 4.1 Important Safety Instructions DANGER! Adhere to the “Important Safety Instructions”... -
Page 13: Frame Grounding Connection
Vertiv™ NetSure™ Supervision Module for Distribution Unit Plus Installation and User Manual 4.3 Frame Grounding Connection A frame ground stud (M3) is located on the outside of the Vertiv™ NetSure™ SM-DU+ assembly. Procedure Connect a frame ground lead to the frame ground stud located on the NetSure™ SM-DU+ assembly. Refer to Figure 4.1 for location. -
Page 14: Load Shunt Input Connections
Vertiv™ NetSure™ Supervision Module for Distribution Unit Plus Installation and User Manual 4.4 Load Shunt Input Connections The Vertiv™ NetSure™ SM-DU+ assembly provides connections for up to twenty-five (25) load shunt inputs. See also “Switch Settings” on page 3. Procedure Connect up to twenty-five (25) load shunt inputs to the NetSure™... - Page 15 Vertiv™ NetSure™ Supervision Module for Distribution Unit Plus Installation and User Manual Figure 4.2 Vertiv™ NetSure™ SM-DU+ Assembly Shunt and Fuse Alarm (FA) Inputs Connections NetSure™ SM-DU+ Assembly Top View Terminal Blocks Wire Size Capacity: 16-26 AWG. Recommended Torque: 2.2 in-lbs.
-
Page 16: Input Power Connections
4.6 Input Power Connections Input power must be supplied to each Vertiv™ NetSure™ SM-DU+ assembly installed in the system. A cable is factory provided for this connection. The ungrounded input lead should be fused at 1-1/3 ampere. Refer to Figure 4.3 for input power connection location. -
Page 17: Ncu Can Bus Connections
Vertiv™ NetSure™ Supervision Module for Distribution Unit Plus Installation and User Manual 4.7 NCU CAN Bus Connections Refer to Figure 4.4. Procedure (Connecting First Vertiv™ NetSure™ SM-DU+ Assembly to NCU) Connect the NetSure™ SM-DU+ assembly into the NCU CAN Bus. Connect CAN_H to CAN_H. Connect CAN_L to CAN_L. - Page 18 Vertiv™ NetSure™ Supervision Module for Distribution Unit Plus Installation and User Manual Figure 4.4 Vertiv™ NetSure™ SM-DU+ Assembly CAN Bus Connections NetSure™ SM-DU+ Assembly Top View Cable P/N 562868 provided. To power system’s CAN H Terminal. To power system’s CAN L Terminal.
-
Page 19: Operation
Vertiv™ NetSure™ Supervision Module for Distribution Unit Plus Installation and User Manual 5 Operation The Vertiv™ NetSure™ SM-DU+ assembly monitors load shunt inputs and fuse alarm inputs and reports this data to the NCU controller. 5.1 Indicators There is one (1) status and alarm indicator located on the NetSure™ SM-DU+ circuit card. The function of this indicator is as shown in Table 5.1. -
Page 20: Configuring The Ncu Sm-Du+ Parameters
Vertiv™ NetSure™ Supervision Module for Distribution Unit Plus Installation and User Manual 5.2 Configuring the NCU SM-DU+ Parameters Refer to the NCU controller manual (UM1M830BNA) for detailed instructions on how to program the monitored inputs to the SM-DU+ assembly. - Page 21 Vertiv™ NetSure™ Supervision Module for Distribution Unit Plus Installation and User Manual Connect with Vertiv on Social Media https://www.facebook.com/vertivI https://www.instagram.com/vertiv/ https://www.linkedin.com/company/vertiv/ https://www.twitter.com/vertiv/...
- Page 22 Vertiv.com | Vertiv Headquarters, 1050 Dearborn Drive, Columbus, OH, 43085, USA © 2021 Vertiv Group Corp. All rights reserved. Vertiv™ and the Vertiv logo are trademarks or registered trademarks of Vertiv Group Corp. All other names and logos referred to are trade names, trademarks or registered trademarks of their respective owners. While every precaution has been taken to ensure accuracy and completeness here, Vertiv Group Corp.