Stihl HT 105 Instruction Manual page 37

Cutting attachment HT 135
The actual cutting length may be less
than the specified cutting length.
Rollomatic E Mini / Rollo Light 01 guide
bar
Blade length: 25, 30, 35 cm
Pitch: 3/8" P (9.32 mm)
Groove width: 1.1 mm
Rollomatic E Mini / Rollo Light 01 guide
bar
Blade length: 25, 30, 35 cm
Pitch: 1/4" P (6.35 mm)
Groove width: 1.1 mm
Saw chain 3/8" P
Picco Micro Mini 3 (61 PMM3)
Type 3610
Pitch: 3/8" P (9.32 mm)
Drive link gauge: 1.1 mm
Saw chain 1/4" P
Picco Micro3 (71PM3) Type 3670
Pitch: 1/4" P (6.35 mm)
Drive link gauge: 1.1 mm
Chain sprocket
7-tooth for 3/8" P
8-tooth for 1/4" P
Sound and Vibration Levels
Noise and vibration data measurements
include idling and rated maximum speed
with the same duration of exposure.
HT 105, HT 134, HT 135
For further details on compliance with
Vibration Directive 2002/44/EC see
www.stihl.com/vib
Sound pressure level L
peq
HT 105: 92 dB(A)
HT 134: 92 dB(A)
HT 135 3/8" P: 93 dB(A)
HT 135 1/4" P: 92 dB(A)
Sound power level L to ISO 22868
w
HT 105: 108 dB(A)
HT 134: 109 dB(A)
HT 135 3/8" P: 109 dB(A)
HT 135 1/4" P: 109 dB(A)
Vibration level a to ISO 22867
hv,eq
HT 105
Shaft compressed
Shaft: 5.0 m/s
Control handle: 5.5 m/s
Shaft extended
Shaft: 5.0 m/s
Control handle: 5.0 m/s
HT 134
Shaft:
HT 134 3.2 m/s
Control handle:
HT 134 3.2 m/s
HT 135
Shaft compressed
Shaft: 4.3 m/s
Control handle: 4.8 m/s
Shaft extended
Shaft: 4.8 m/s
Control handle: 5.0 m/s
The K-factor in accordance with
Directive 2006/42/EC is 2.0 dB(A) for
the sound pressure level and sound
power level; the K-factor in accordance
to ISO 22868
with Directive 2006/42/EC is 2.0 m/s
for the vibration level.
REACH
REACH is an EC regulation and stands
for the Registration, Evaluation,
Authorisation and Restriction of
Chemical substances.
For information on compliance with the
REACH regulation (EC) No. 1907/2006
see www.stihl.com/reach.
Exhaust Emissions
The CO value measured in the EU type
2
approval procedure is specified at
2
www.stihl.com/co2.
2
The measured CO
determined on a representative engine
2
in accordance with a standardized test
2 procedure under laboratory conditions
and does not represent either an explicit
or implied guarantee of the performance
of a specific engine.
2
The applicable exhaust emission
requirements are fulfilled by the
intended usage and maintenance
2
described in this instruction manual. The
type approval expires if the engine is
modified in any way.
2
2
2
2
English
2
value was
2
35