Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Harper DewEze S3
Summary of Contents for Harper DewEze S3
- Page 1 S3 SUPER SLICER OPERATOR’S & PARTS MANUAL 8-2021...
-
Page 3: To The Owner Or Operator
(620) 896-7381 • Fax (620) 896-7129 Toll Free 800-835-1042 Email info@deweze.com Website www.deweze.com © 2021 Harper Industries, Inc. The Harper and DewEze names are registered trademarks of Harper Industries, Inc. All other brand and productnames are trade- marks or registered trademarks of their respective companies. -
Page 4: Warranty Statement
Statement of Warranty Harper Industries, Inc. (HII) warrants to each purchaser of a new DewEze S3 from an authorized dealer or representative, that such equipment is free of manufacturer’s defects in workmanship and materials which appear while in normal service for a period of ONE YEAR commencing with delivery to the original user. -
Page 5: Table Of Contents
Table of Contents OPERATOR SECTION To the Owner or Operator..........Warranty Statement............Table of Contents............Specifications..............Safety Guidelines............Set-Up Instructions............Operation Hydraulic Requirements........Loading Instructions......... Feeding Instructions......... Adjustments Feed Rate............Flow Control Valve Adjustments....... Table Speed Operating Range......Suggusted Rebaling Settings......Suggested Bunk Feeding Settings.... -
Page 6: Specifications
91.63” H x 148” L 102.0” W Tire Pressure 35 psi cold NOTE: Following publication of this manual, certain changes in standard equipment and options may have occurred which would not be included in these pages. Your Harper dealer is the best source for up-to-date information. -
Page 7: Safety Guidelines
Safety Decals Safety Guidelines • If safety related or instructional decals become illegible or are removed, re- place them immediately. New decals • Use genuine factory parts or parts may be obtained from your local Harp- with equivalent characteristics, includ- er Dealer. -
Page 8: Set-Up Instructions
• Grease Lubrication Points on lower Set-Up Instructions fork (3 Grease Zerks) S3 Load Arm Assembly • Remove Load arm from inside of table, and lay on ground • Align load arm bolt flanges with table flanges • Bolt the load arm flanges on the back side of the table flanges, with the (9) bolts, flat &... -
Page 9: Operation
THAT NO DAMAGE HAS OCCURRED DUR- ING SHIPPING. HYDRAULIC REQUIREMENTS Your new DEWEZE S3 is designed to be used as a mobile feeding unit mounted on a trailer or as a stationary unit in a permanent installation. Regardless of the type of use... -
Page 10: Loading Instructions
LOADING INSTRUCTIONS Flow (speed) must be controlled on the tractor remote outlet. To set this (Trailer Mounted Unit Only) speed first set the Slicer flow as outlined in the manual. Secondly, Approach the bale on its right side with the turn the flow control toward the “turtle”... -
Page 11: Adjustments
Suggestion: When adjusting the sickle and Adjustments the backboard sliding with it, loosen the bolts and nuts shown. There are nuts, bolts, and FEEDING RATE straps on both the front and rear sides of the machine. The feeding rate may be adjusted by chang- ing the speed of the feeder chain, or by Retighten the four 5/8”... -
Page 12: Suggusted Rebaling Settings
TABLE SPEED OPERATING RANGE Arm Width Adjustment Measurements • Flow Control Valve Between 2 – 7. • Below 2 can cause the table to stall out. • Above 7 any increase in speed with be negligible, and could allow flow to by- pass. -
Page 14: Maintenance Schedule
Maintenance TRAILER MAINTENANCE MONTHLY (Or every 100 bales) Grease the linkage of the lift arm to avoid binding and rust. ANNUALLY Clean and repack the wheel bearings. TABLE MAINTENANCE MONTHLY (Or every 100 bales) Grease Shumacher gear box with MAX 5 shots of lithium based grease every 50 operating hours. - Page 15 Lubricate the system drive chains with chain oil. - Non-detergent petroleum based or synthetic, multigrade 20/50 oil. Inspect Schumacher drive belt for stretching from normal wear, tighten belt as necessary. Inspect for unusual/excessive belt wear such as fraying, glazing, or other abnormalities, replace as necessary.
-
Page 17: Parts Section
PARTS SECTION... -
Page 19: Trailer Assembly
Table of Contents PARTS SECTION Table and Feed Chain........Trailer Assembly..........Hub and Bearing Assembly......Backboard and Sides........Safety Shields........... Table Safety Stops........... Sickle Height Adjustment........Twine Box - Optional......... Decals............... Sickle Drive Assembly........PTO Kit............. Sickle Assy............PTO Holder............Hose Assy - PTO.......... - Page 21 ii 1.1...
- Page 22 iii 1.1...
- Page 23 iv 1.1...
- Page 33 ii 1.9...
- Page 37 ii 2.3...
- Page 41 ii 2.5...
- Page 43 ii 2.6...
- Page 44 iii 2.6...
- Page 45 NOTES Harper Industries, Inc. Telephone: 620-896-7381 151 E. Highway 160 Toll-Free: 800-835-1042 Harper, KS 67058 Fax: 620-896-7129 Website: www.harperindustries.com E-mail: info@harperindustries.com...
Need help?
Do you have a question about the DewEze S3 and is the answer not in the manual?
Questions and answers