Advertisement
Quick Links
Operation Manual
Ground Drill
62350, 62351
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ insignificantly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for WilTec 62350
Summary of Contents for WilTec 62350
- Page 1 Operation Manual Ground Drill 62350, 62351 Illustration similar, may vary depending on model Read and follow the operating instructions and safety information before using for the first time. Technical changes reserved! Due to further developments, illustrations, functioning steps and technical data can differ insignificantly.
- Page 2 All rights re- served. The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual, nor in the diagrams and figures shown.
- Page 3 Warnings found on the device Caution! Fire hazard! Caution! Hot surfaces! Caution! Toxic gas! Wear ear protection. Read the operation manual. © by WilTec Wildanger Technik GmbH Item 62350, 62351 Page 3 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 4 • Do not touch the motor or the carburettor while or shortly after operation. Non-compliance bears the risk of burns. © by WilTec Wildanger Technik GmbH Item 62350, 62351 Page 4 http://www.WilTec.de http://www.aoyue.eu...
- Page 5 (Fig. 1, B) from the connection plate. • Turn the right handle (Fig. 2, C) downward as depicted in fig. 2 and keep moving it until it reaches the position shown in fig. 3. © by WilTec Wildanger Technik GmbH Item 62350, 62351 Page 5 http://www.WilTec.de http://www.aoyue.eu...
- Page 6 Connect the auger (Fig. 4, D) to the device by placing it onto the shaft (Fig. 4, E) and secure it with the help of the bolt (Fig. 4, F) and the cotter pin (Fig. 4, G). © by WilTec Wildanger Technik GmbH Item 62350, 62351 Page 6 http://www.WilTec.de...
- Page 7 Left handle bar Cotter pin Control handle Base plate Bolt Right handle bar Gasket Screw Auger Connecting plate Handle Fixture Screw Gearbox Base plate Screw © by WilTec Wildanger Technik GmbH Item 62350, 62351 Page 7 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 8 № № Name Name Starter Auger Fuel tank Control handle Left handle bar Right handle bar Gearbox Motor Handle © by WilTec Wildanger Technik GmbH Item 62350, 62351 Page 8 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 9 Never fill the fuel tank while the motor is operating and instead ensure that the motor has been turned off before placing the device on an even ground in order to prevent two-stroke mixture from spilling in the process. © by WilTec Wildanger Technik GmbH Item 62350, 62351 Page 9 http://www.WilTec.de...
- Page 10 Do not pull the rope as far as it will go, since this will damage the rope start. • Always let the rope slide back slowly in order to allow it to roll up properly. © by WilTec Wildanger Technik GmbH Item 62350, 62351 Page 10 http://www.WilTec.de...
- Page 11 Make sure to regularly check the petrol filter (Fig. 14, U) and replace it immediately, in case of it being heavily polluted. A polluted petrol filter may cause issues while starting the device as well as a loss of performance. © by WilTec Wildanger Technik GmbH Item 62350, 62351 Page 11 http://www.WilTec.de...
- Page 12 Check the condition of the auger before every use and sharpen or replace it, if necessary. Always make sure to choose the auger according to the requirements of the task at hand (Fig. 16). © by WilTec Wildanger Technik GmbH Item 62350, 62351 Page 12 http://www.WilTec.de...
- Page 13 • Store the ground drill within a dry environment inaccessible to children. Make thereby sure that it is stored with sufficient distance to the ground and potential heat sources. © by WilTec Wildanger Technik GmbH Item 62350, 62351 Page 13 http://www.WilTec.de...
-
Page 14: Troubleshooting
Drain fuel and replace. Motor is very noisy or Combustion chamber is polluted Clean combustion chamber. stutters Moving parts are worn Check and replace worn parts. © by WilTec Wildanger Technik GmbH Item 62350, 62351 Page 14 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de... - Page 15 Important notice: The reprint or reproduction, even of excerpts, and any commercial use, even in part, of this instruction manual require the written permission of WilTec Wildanger Technik GmbH. © by WilTec Wildanger Technik GmbH Item 62350, 62351 Page 15 http://www.WilTec.de...
Need help?
Do you have a question about the 62350 and is the answer not in the manual?
Questions and answers