Advertisement
MAJOR COMPONENTS AND WHAT THEY DO
Tank and Air Volume Control
The tank serves two functions. It provides a reservoir
of water, so that the pump doesn't need to start every
time water is drawn from a fixture in the house, and it
maintains a cushion of air under pressure.
When SEARS Captive Air
ume control is necessary. This tank contains a perma-
nent precharge of air.
When a SEARS Standard Tank is used, an air volume
control adds air to the tank when it is needed. See in-
structions included with Air Volume Control for details
on installation and operation.
Pressure Switch
The pressure switch provides automatic control.
Model No.
Pump Starts At
390.250252
30 Pounds
Impeller and Jet
The impeller of the pump rotates with the motor shaft,
causing the water to fly out from its rim by centrifugal
force. The rotation of the impeller creates a vacuum
which pulls in more water. Part of the water is diverted
back to the jet where it passes through the nozzle and
venturi, creating additional vacuum to draw in more
water and delivering it at a high pressure to the im-
peller.
Because of the shallow setting, the vacuum created by
the pump is sufficient to pull water to the pump, there-
fore, the jet assembly is attached directly to the pump.
Piping In The Well
A Shallow well jet pump can be installed on a dug well,
drilled well or with a driven point. SEARS shallow well
jet pumps have a built-in check valve. In a dug or cased
well, a foot valve and strainer is recommended and
should be installed 5 to 10 feet below the lowest level
to which the water will drop while pump is operating
(pumping water level), See Figure 3, Page 4. Your well
driller can furnish this information. The strainer should
not be too close to the bottom, or sediment may clog
it. Before installing foot valve, check to see that it work
freely.
When using a foot valve, a priming tee and a plug as
shown in Figure 1, is recommended.
Be sure the total lift from the pumping water level to
the pump does not exceed 20 feet if the pump is over
the well, or less if the pump is offset from the well.
Both figures are for sea level – the maximum lift at
which the pump can operate satisfactorily decreases
with the elevation at the approximate rate of 1 foot per
1,000 feet of elevation. Thus, if the lift is 17 feet and
your elevation is 3,000 feet above sea level, you would
then be pumping 17 plus 3 or 20 feet. This is still sat-
isfactory for shallow well pumping.
®
Tanks are used, no air vol-
Pump Stops At
50 Pounds
Horizontal Piping From Well To Pump
On well point installations where the horizontal pip-
ing is more than 25 feet, a check valve should be in-
stalled as shown in Figure 3, Page 4.
When the pump is offset more than 25 feet from the
well, horizontal piping should be increased in size to
reduce friction losses. In no case should the offset pip-
ing be smaller than the suction tapping of the pump.
Horizontal Offset Piping Sizes
for Shallow Well Jets
1-1/4"
Up to 25 Ft.
Discharge Pipe Sizes
When the pump is set a distance from the house or
point of water use, the discharge pipe size should be
increased to reduce pressure losses caused by friction.
1"
Up to 25 Ft.
Emergency Power
In some areas and with some installations, an emer-
gency power supply to guard against power failure is a
good idea. If you install an engine-generator set for
emergency backup power for your pump, supply the
generator set manufacturer with the nameplate data
from the pump motor. He will then be able to provide
a generator of the correct size to power your pump.
Also, be sure to add the load from any other accessories
(such as lights) that may be on the same circuit.
To
Service
1251 0994
Figure 1
3
1-1/2"
2"
25 to 50 Ft.
50 to 200 Ft.
1-1/4"
1-1/2"
25 to 100 Ft.
100 to 600 Ft.
Priming
Port
Priming
Tee
Check
Valve
Advertisement
