Download Print this page
Mercia Garden Products 8x8 Helios Summerhouse General Instructions Manual

Mercia Garden Products 8x8 Helios Summerhouse General Instructions Manual

Advertisement

Quick Links

General Instructions
03HEL0808DDFW-V2
8x8 Helios Summerhouse
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-
driver, Stanley knife, wood saw, step ladder and drill with 2mm bit.
- Ensure there is plenty of space and a clean dry area for assembly.
TIMBER
As with all natural materials, timber can be a ected during various weather conditions. For the duration of heavy or
extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during
excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be
helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine
and sheltered as much as possible during rain or snow.
Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent
the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.
Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-
ment to prevent water ingress
Pressure Treated buildings - Require a waterproof treatment to prevent water ingress
Log Cabins - Are supplied untreated and require a preservative and waterproo ng treatment.
BUILDING A BASE
When thinking about where the building and base is going to be constructed:
Ensure that there will be access to all sides for maintenance work and annual
treatment.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base
dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding
should overlap the base, creating a run o for water. It is also recommended that the oor be at least 25mm above
the surrounding ground level to avoid ooding.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens
products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or
using this product.
Refer to the instructions pages for you speci c product code
Please retain product label and instructions for future reference
x2
All building's should be
erected by two adults
For ease of assembly, you
MUST pilot drill all screw
holes and ensure all screw
heads are countersunk.
2mm Drill bit
**Protim Aquatan T5 (621)**
Your building has been treated with Aquatan.
Aquatan is a water-based concentrate which is diluted with water, the building as been treated by the correct
application of Aquatan solution and then allowed to dry.
Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and
garden buildings.
Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl
sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.
For assistance please contact customer care on: 01636 821215
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
www.merciagardenproducts.co.uk
Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
CAUTION
Every e ort has been made during the
manufacturing process to eliminate the
prospect of splinters on rough surfaces of the
timber. You are strongly advised to wear gloves
when working with or handling rough sawn
timber.
P 1

Advertisement

loading
Need help?

Need help?

Do you have a question about the 8x8 Helios Summerhouse and is the answer not in the manual?

Questions and answers

Summary of Contents for Mercia Garden Products 8x8 Helios Summerhouse

  • Page 1 All building’s should be Winter = High Moisture = Expansion erected by two adults Summer = Low Moisture = Contraction 03HEL0808DDFW-V2 8x8 Helios Summerhouse BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY For ease of assembly, you CAUTION MUST pilot drill all screw Every e ort has been made during the - Check the pack and make sure you have all the parts listed.
  • Page 2 03HEL0808DDFW-V2 Please retain product label and instructions for future reference Overall Dimensions: Length = 2506mm Width = 2942mm Height = 2137mm Base Dimensions: Key Plate Hinge QTY 6 Turn Button QTY 2 Tower Bolt QTY 2 Length = 2387mm PI-07-0023 PI-07-0034 PI-07-0114 Width = 2400mm...
  • Page 3 Please retain product label and instructions for future reference Step 1 Step 2 Door Fixings Join the ush hinges (No. 24) to the Position the oor (No.5)sections door frames (No. 7 & 8) using together as shown in the 30mm screws. Ensure hinges are illustration, ensure that the oors attached using the outer plate of are ush together and secure into...
  • Page 4 Please retain product label and instructions for future reference Step 3 Step 2 Continued... Fix the door bar (No. 20) to the Place the back panel (No.4) and the inside of the slave door using right gable (No. 2)onto the oor. 6x30mm screws as shown in the illustration.
  • Page 5 Please retain product label and instructions for future reference Step 6 Step 5 Place the rst ridge bar Following the same method outlined (No.9) inside the building in step 3, place the assembled door and line up with the upright panel onto the oor inbetween the framing on each gable.
  • Page 6 Please retain product label and instructions for future reference Please retain product label and instructions for future reference Step 8 Step 7 Position the roof ends (No. 13) onto Place the rst roof panel (No. 6) onto the roof, ensuring the tongue and the supports (making sure the roof groove align and the boards sit framing sits behind the support bar)
  • Page 7 Please retain product label and instructions for future reference Step 10 Step 12 Fix the fascia’s (No. 17) to the front Cut the felt into 4x strips and lay onto of the building using 4x40mm the roof in the order shown in the screws.
  • Page 8: After Treatment

    Please retain product label and instructions for future reference Step 14 Fix the turn button’s (No. 25) to the top and bottom of the slave door using 2x 30mm black screws. 2x30mm Black Screws 30mm Pre drill screw hole *These turn buttons help keep your doors straight during high and low levels of moisture content in the air. Step 15 Fix the large rain guard (No.

This manual is also suitable for:

03hel0808ddfw-v2