Advertisement
Quick Links
Advertisement
Related Manuals for LAZBOY CHR10084A-C
Summary of Contents for LAZBOY CHR10084A-C
- Page 1 ASSEMBLY Instructions Executive Chair Model: CHR10084A-C...
- Page 2 Should you prefer to speak with a customer service representative, you may call toll free : 1-855-372-2315 U.S. 6am - 5pm PST, U.K. 2pm - 1am 0-800-051-6775...
- Page 3 Guidelines FAILURE TO FOLLOW THESE WARNINGS WHEN IN USE COULD RESULT IN INJURY Do not stand on the item or use as a step ladder. • The piece has been tested and approved for users • weighing up to 275 lbs (125kg) per seat. Do not use this item unless all bolts and screws are •...
- Page 4 Pre-Assembly Preparation: Please read through this instruction booklet before beginning assembly of this item. WARNING : DO NOT LET Two adults are recommended for assembly. CHILDREN PLAY IN OR Clear out the space for assembly and lay out all • AROUND THE UNIT DUE parts on Parts List, extra room will allow you to TO THE POSSIBLE RISK...
-
Page 5: Parts List
Parts List Casters Star Base Gas Lift Seat Plate Arms Quantity: 5 Quantity:1 Quantity: 1 Quantity: 2 Quantity: 1 1-1/4” Screws 1” Screws Seat Cushion Back Cushion Plastic Shroud Quantity: 6 Quantity: 2 Quantity:1 Quantity: 1 Quantity: 1 2” Screws with Spring Plastic Caps Allen Key Quantity: 4... - Page 6 Step 1 Step 2 Place the Star Base (B) upside down and insert 5 Casters (A) into the holes Turn the Star Base (B) over and insert the Gas Lift (C) through the center hole on top of Star Base (B). on the Star Base (B).
- Page 7 Step 3 Step 4 Attach Seat Plate (D) to the bottom of the Seat Cushion (F) (with the front Insert Levers (D1 & D2) of Seat Plate (D) to the pre-attached cable of the seat plate facing the front of seat cushion). Attach by using 1-1/4” lever receivers on the underside of Seat Cushion (F) (with the front Screws (I) for the front holes of the Seat Plate (D) and 1”...
- Page 8 Step 5 Step 6 Attach the Back Cushion (G) to the Seat Cushion (F) by positioning the Insert 2” Screws with Spring Washers (K) into arm holes, attaching back support plate over the Seat Plate (D) with 1-1/4” Screws (I). Arms (E) (with the front of arms facing the front of seat cushion) to *Note: Do not tighten the screws completely.
- Page 9 Step 7 Step 8 Put the Plastic Shroud (H) over the Seat Plate (D) (with the front of plastic Position the assembled chair upright with the seat plate facing down. shroud facing the front of seat cushion). Align shroud posts to holes on Insert the Gas Lift (C) into the center hole of the Seat Plate (D).
- Page 10 Step 9 Press the Plastic Caps (L) into armrest holes once all screws have been tightened.
- Page 11 Operating Instructions Function Instruction - 1 To Adjust Seat Height: While seated, lean forward and reach under the right side of the chair to find the lever. Lift the lever and raise your body up slightly to allow the chair to rise to the desired height. Once desired height is reached, release lever to lock chair at desired height.
- Page 12 Function Instruction - 2 To Operate Tilt Lockout: While seated, reach under the left side of the chair to find the lever. Push down the lever and lean back to allow the chair to tilt backwards. To lock the chair in the upright or vertical position, sit upright and pull the lever to the up position.
- Page 13 Function Instruction - 3 To Adjust Tension On The Tilt: Reach under the front center of the chair, grasp the round knob (R) and turn it counter - clockwise to stiffen the tilt mechanism for a heavier user. Turn the knob (R) clockwise to loosen the tilt mechanism for a lighter user.
- Page 14 Function Instruction - 4 360˚ Swivel: 360˚ seat swivel.
-
Page 15: Limited Warranty
Limited Warranty The exceptions or exclusions to this warranty are: • Upholstery material and foam cushion material is The product you have purchased is warranted against warranted against defects in material and workmanship defects in material and workmanship while owned by for a period of one year, beginning on the date of the “Original Purchaser”.