Page 1
MANUAL inverter semi-automatic WELDING Model: MIG / MMA 160 Mini Drawings devices in the manual may differ from the original colors. Original instructions. with NOTE: Please use a welder after a very careful reading the manual. 1. In order to ensure safety should be determined by qualified personnel responsible for installation, maintenance, periodic inspection and repair equipment.
Table of Contents 1. INTENDED USE ..........3 1. INTENDED USE ..........3 1. INTENDED USE ..........3 1. INTENDED USE ..........3 2. TECHNICAL DATA ................3 2. TECHNICAL DATA ................3 2. TECHNICAL DATA ................3 2.
1. INTENDED USE 1. INTENDED USE It is a semi-automatic welding The device brand MAGNUM MIG / MMA_160_mini The device brand MAGNUM MIG / MMA_160_mini designed for manual electric welding of low carbon steel, low-alloy (MAG), alloy steel (MIG), and aluminum and its alloys.
3. PRECAUTIONS FOR USE 3. PRECAUTIONS FOR USE Please read all safety regulations and all instructions. Failure to comply with Please read all safety regulations and all instructions. Failure to comply with safety regulations and instructions may result in electric shock, fire and / or serious injury.
Page 5
d) prepare adequate protection face and eyes, e) check the condition of the welding connections and the operating handle, check whether the execution of the welding does not endanger the environment (radiation curve, the possibility of ignition elements flammable) g) check whether in the case of welding on the wall, the other side can not occur inflammation, 3.3.
Page 6
d) Organize welding equipment. 3.6. Final remarks. a) When performing welding work inside the tanks, boilers or other confined spaces (to 15m3), a welder should be insured by another person, who will remain on the outside. ELECTRIC SHOCK CAN KILL: Welding apparatus produce a high voltage. Do not touch the torch or welding material ELECTRIC SHOCK CAN KILL: Welding apparatus produce a high voltage.
4. SYMBOLS 4. SYMBOLS To reduce the possibility of injury, the user must first read all the instructions. General warning sign notes for each user on the general danger. It is combined with other instructions warning or other symbols that failure can lead to personal injury or equipment damage.
5. CONSTRUCTION AND CONTROL PANEL 5. CONSTRUCTION AND CONTROL PANEL 1. Welding current regulator. 1. Welding current regulator. 2. The switch methods MIG / MMA. 2. The switch methods MIG / MMA. 3. Signaling overheating. 3. Signaling overheating. 4. Current socket, output polarity "minus". 4.
6. KIT CONTENTS 6. KIT CONTENTS The following items should be included: The welding device with a handle MIG-MAG x 1 pc. Work cable MMA x 1 pc. Cable to the common terminal x 1 pc. Attention! For the safety of children should not be left freely accessible parts of the packaging (plastic bags, cardboard, polystyrene, etc.).
Insulated wire of yellow-green is grounded and should always be connected to the outlet marked earth, regardless of whether there is power supply 230 [V] and 400 [V]. Symbol earth (PE). 7.2 Inserting the conductors MIG-MAG welding. ATTENTION! Before all work carried out on the unit, unplug the power cord. 1.
4. The end of the wire wound on the spool, flatten or cut off the bent section, then 4. The end of the wire wound on the spool, flatten or cut off the bent section, then file off, so that was not sharp. 5.
Page 12
welding in a plane perpendicular to the direction of welding. In the case of filling the wide grooves in the flat position or the vertical end of the handle must be performed lateral swinging movements. During welding, the welding gun should be conducted at a right angle relative to the parts to be welded.
protective gas Chemical action welded metal inert Basically, all metals except for carbon steels Al, Cu, Cu alloys, Mg alloys, ensured high heat input welding inert Al, Cu alloys, Cu, Mg, there is provided a large heat input welding, low 20-80% Ar + He inert thermal conductivity gas...
welding speed, thickness, the type of the electrode and the work piece. The amount of current is adjusted so that it could probably ignite the arc, and in the course of welding was steady and stable. For example, the electrode "Pink 6012" needs to 2.0 mm - 40 to 60 A 2.5 mm - 50 to 70 A, 3.25 mm - 70 to 110 A, 4.0 mm - 110 ÷...
• Replace or repair damaged or worn parts. Every month? • Check the condition of the electrical connections inside the source. • Oxidized surfaces should be clean and tighten loose parts. • Clean the inside of the device by means of compressed air. 9.
11. UTILIZATION 11. UTILIZATION The packaging materials for use as a secondary raw material. Disposal of packaging should be in accordance with local regulations. Packaging materials must be protected from children, because they represent a potential source of danger. Proper disposal of this product: 1.