Metabo FSX 200 Intec Original Instructions Manual page 9

8. Cleaning, Maintenance
Empty dust collection box (4).
- Open cleaning flap (5).
- Empty dust collection box (4).
- Remove fluted filter (6) and knock off dust stuck to
filter or remove with brush.
- When inserting, ensure that the fluted filter (6) is
inserted in the lateral guides.
Clean the machine regularly. This includes
vacuum cleaning the ventilation louvres on the
motor.
Replacing a worn support plate (2)
- Remove fixing screws (on lower side of support
plate).
- Remove support plate.
- For replacement support plates, refer to the
Accessories chapter.
- Mount support plate.
- Refit fixing screws (on lower side of support plate)
and tighten.
Replacing support plate brake / braking ring
If the idling speed of the support plate increases in
the course of time, the braking ring is worn and must
be replaced in a service workshop for Metabo
power tools.
Note: If abrasive material (e.g. gypsum, etc.) is
being sanded, the braking ring inevitably wears
faster.
9. Accessories
Use only genuine Metabo accessories.
See page 4.
Use only accessories which fulfil the requirements
and specifications listed in these operating instruc-
tions.
A Support plate with velcro-type fastening
(as replacement)
B Adhesive intermediate disc
C Adhesive sanding discs
D Adhesive polishing sponge
E Lambskin adhesive polishing disc
F Adhesive polishing felt
G Adhesive sanding fleece
H Adhesive sanding screen
I Fluted filter (as replacement)
J Dust collection box (as replacement)
K Dust extraction connection
L Metabo universal vacuum cleaner
For complete range of accessories, see
www.metabo.com or the main catalogue.
10. Repairs
Repairs to electrical tools must be carried out
by qualified electricians ONLY!
If you have Metabo electrical tools that require
repairs, please contact your Metabo service centre.
For addresses see www.metabo.com.
You can download spare parts lists from
www.metabo.com.
11. Environmental Protection
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Guideline 2002/
96/EC on used electronic and electric equipment
and its implementation in national legal systems,
used power tools must be collected separately and
handed in for environmentally compatible recycling.
12. Technical Specifications
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
D = Dimensions of sanding plate
P = Nominal power input
1
P = Power output
2
n = Idle speed
0
n = Speed at rated load
1
s = Orbital frequency at no load
0
s = Orbital frequency at nominal load
1
S = Oscillating circuit diameter
Intec = Dust collection box
m = Weight without mains cable
Measured values determined in conformity with
EN 60745.
Machine in protection class II
~
Alternating current
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. Depending on the operating
conditions, the condition of the power tool or the
accessories, the actual load may be higher or lower.
For assessment purposes, please allow for breaks
and periods when the load is lower. Based on the
adjusted estimates, arrange protective measures
for the user e.g. organisational measures.
Vibration total value (vector sum of three directions)
determined in accordance with EN 60745:
a = Vibration emission value
h, DS
(sanding surfaces)
a = Vibration emission value
h, P
(polishing)
K /K =Uncertainty (vibration)
h,DS h,P
Typical A-effective perceived sound levels:
L = Sound pressure level
pA
L = Acoustic power level
WA
K , K = Uncertainty
pA WA
During operation the noise level can exceed
80 dB(A).
Wear ear protectors!
ENGLISH en
9