CrimeStopper RS-999.FM Installation Instructions Manual
Coolstart series vi remote engine starting system 2-way paging system
Hide thumbs
Also See for RS-999.FM:
- Installation instructions manual (28 pages) ,
- Installation instructions manual (16 pages) ,
- Installation instructions manual (26 pages)
Table of Contents
Advertisement
COOLSTART SERIES VI
RS900/RS901
RS999 FM / TW1 2-WAY PAGING SYSTEM
Congratulations on your choice of a Crimestopper CoolStart™ remote engine starter! This installation Handbook covers
the following models: RS900 VI Remote Start & Keyless Entry System, RS901 Upgrade/Expansion module (No remotes
or antenna), and the 2-Way RS999FM/TW1 system with 2-Way FM paging technology.
This installation book is designed for the installer or individual with an existing understanding of automotive electrical
systems, along with the ability to test and connect wires for proper operation. To ease installation, we suggest that you
READ THIS MANUAL before beginning your installation. This book is provided as a GENERAL GUIDELINE and the
information contained herein may differ from your vehicle.
DISCLAIMER:
Crimestopper Security Products, Inc. and its' vendors shall not be liable for any accident resulting from the use of this
product. This system is designed to be professionally installed into a vehicle in which all systems and associated
components are in perfect working condition.
TECHNICAL SUPPORT: (800) 998-6880
Monday - Friday 8:00am - 4:30pm Pacific Std. Time
Web Site: www.crimestopper.com
E-mail: tech-support@crimestopper.com
CRIMESTOPPER SECURITY PRODUCTS, INC.
1770 S. TAPO STREET, SIMI VALLEY, CA. 93063
REV A 06.2003
REMOTE ENGINE STARTING SYSTEM
INSTALLATION INSTRUCTIONS
INTRODUCTION
This device complies with FCC Rules part 15. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference that
may be received, including interference that may cause undesired
operation. The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment.
Such modification could void the user's authority to use the
equipment.
Advertisement
Table of Contents
Related Manuals for CrimeStopper RS-999.FM
Summary of Contents for CrimeStopper RS-999.FM
-
Page 1: Installation Instructions
DISCLAIMER: Crimestopper Security Products, Inc. and its’ vendors shall not be liable for any accident resulting from the use of this product. This system is designed to be professionally installed into a vehicle in which all systems and associated components are in perfect working condition. -
Page 2: Table Of Contents
TABLE OF CONTENTS Pre-Installation Considerations……….………...……...……………………………………………………………….……2 Cautions & Warnings…….…………...….……..…..……………………………………………………………….…..……3 Wiring……..…………………………...……………………………………………………………………………….…….3-7 Wiring High-Current Connector…….………………...…………………………………………………………………...8-9 Power Door Lock Wiring...………………………………………….…………….……..…………...……………………10-11 Smart Tachless, Tach Reference, Tach Finder, & Timed Crank Modes…………………..…..………...…...………12-14 Diesel Glow Plug Delay..………………….…………………………………...……………………...…..…………………15 Option Programming ………..……………………….…………………………………...……………..…………………15-19 Transmitter / Transceiver Programming……………………….…………………….……………..………...………...….20 2 Vehicle Operation.……………………………….……………………………………...…………………….……………21 Troubleshooting “Before You Call”... -
Page 3: Cautions & Warnings
INSTALLATION CAUTIONS & WARNINGS **FOR SAFETY REASONS, DO NOT INSTALL RS900/901/999FM in vehicles with MANUAL TRANSMISSIONS.** If accidentally left in gear, a remote started vehicle could become a self-propelled threat to life and property. DO NOT extend the RS900/901/999FM Remote start ignition harness length. Mount the module so that main harness reaches all ignition switch wiring. - Page 4 PIN 3: YELLOW/BLACK FOR NEGATIVE IGNITION OUTPUT: (Relay and/or Module not included) YELLOW/BLACK Diode isolate if using both! PIN 3: YELLOW/BLACK: FOR ANTI-GRIND/STARTER DISABLE OUTPUT: (Relay not included) IGN 1 IGN 2 MOTOR START WIRING 3rd IGN (If needed) BROWN YELLOW/BLACK MAKE CERTAIN TO CONNECT "BROWN"...
- Page 5 PIN 4: BROWN: (-) AUX OUTPUT (TRUNK POP) or DOME LIGHT ILLUMINATION OUTPUT This output is programmable for two modes of operation. See Programming Option #9 Page 16. Mode (1) DEFAULT: Provides a Ground pulse when button #3 (Trunk) on the remote transmitter is pushed to activate a factory electric trunk release or other optional accessory.
- Page 6 PIN 5: GREEN: (-) START ACTIVATION INPUT, OEM INTERFACE or TURBO TIMER INPUT See descriptions & diagrams below. See Programming Option #5 on page 16. Mode (1) [Default (-) Neg. Start Activation] This wire allows a host (or parent) alarm’s or keyless entry system to activate a Remote Start by sending a 1-Second Negative signal to the Green input wire to trigger a remote engine start or stop.
- Page 7 WIRING PIN 6: GRAY: (-) NEGATIVE HOOD PIN SWITCH Connect the Gray wire to a switch that is at ground when the hood is open. If an existing switch is not available, then we recommend one be installed. When this wire is grounded, the remote start is inhibited. If hood is opened on a remote started engine, the unit will immediately shut the motor off.
-
Page 8: Wiring High-Current Connector
WIRING: 7-PIN HIGH-CURRENT CONNECTOR BROWN: +12V STARTER OUTPUT 30A: Connect to circuit in the vehicle that has power ONLY while the STARTER MOTOR is CRANKING. GRAY: +12V ACCESSORY OUTPUT 30A: Connect to circuit in the vehicle that provides Accessory Power for systems such as HEAT and A/C. Typically, this wire turns ON with the first position of the key, DROPS OUT WHEN CRANKING, then returns as the engine starts and runs. - Page 9 WIRING: 7-PIN HIGH-CURRENT CONNECTOR 7-PIN High Current Connector PARKING LIGHTS WHITE FUSE +10A or 500mA (-) PINK/WHITE FUEL ENGINE PUMP COIL IGN 2 ACC 2 START 2 IF NECESSARY NOTE: Heavy duty/High Current Ignition circuits greater than 30 AMPS. Industrial vehicles, dual AC, etc. require high- current relays.
-
Page 10: Power Door Lock Wiring
To install aftermarket systems in these vehicles, an interface module is required that converts the regular lock/unlock pulses into “Data messages” to allow locking & unlocking. Interface modules are sold separately. Crimestopper Door Lock Accessories: CS-6600DLM: Dual-relay plug-in module for Reverse Polarity, Positive, or Aftermarket Motors. - Page 11 BASIC DOOR LOCK DIAGRAMS NEGATIVE TRIGGER DOORLOCK WIRING GREEN BLUE REVERSE POLARITY DOOR LOCK WIRING GREEN BLUE MASTER SWITCH POSITIVE TRIGGER DOORLOCK WIRING GREEN BLUE FACTORY POWER LOCKING RELAYS AFTERMARKET MOTOR/DOOR LOCK WIRING GREEN FUSED +12V BLUE FUSED +12V FACTORY POWER LOCKING RELAYS...
-
Page 12: Smart Tachless, Tach Reference, Tach Finder, & Timed Crank Modes
Your CoolStart system includes a unique voltage monitor called “Smart Tachless” mode. This mode allows this unit to efficiently start an engine without the use of a tach signal wire. These modules actively monitor the voltage level of the vehicle to control the starter motor each time a remote start is requested. IMPORTANT NOTES: (1) SETUP may be required for the RS900/901/999FM “Smart Tachless”... - Page 13 TACH REFERENCE, TACH FINDER, TACH PROGAMMING Tach Reference Mode provides reliable remote starting performance though engine speed (RPM) sensing. When using Tach Reference Mode, the Red/White wire is used for Tach signal [Engine RPM] input. Most modern engines include various points where the Engine Speed [Tach] or A/C signal may be obtained. Tach Signal examples: Negative (-) side of ignition coil, at the Distributor or Ignition Control Module, Coil Pack, Engine Computer, or Crankshaft Sensor.
- Page 14 This feature provides an easy method of starting the vehicle without locating an exact tach wire. The system uses an exact timed cranking output combined with the use of the Red/White tach wire as an engine ON/OFF monitor. The Red/White Tach wire must still be used in this mode of operation. THIS FEATURE MUST BE PROGRAMMED BEFORE USE! THERE ARE 2 LEVELS of programming required: First, set the system for “Timed Crank”...
-
Page 15: Diesel Glow Plug Delay
This feature provides a solution for diesel vehicles without having to connect to the Glow Plug-“Wait to Start Circuit”. This may be needed for various reasons. If your vehicle does not have a viable “Wait to Start Circuit”, or you cannot locate and identify the circuit, then change your system to “Diesel Glow Plug Delay”... - Page 16 OPTION PROGRAMMING CHART Option Option Description Engine Monitoring Autolock with Ignition Door Lock Pulse Time Double Unlock Pulse OEM Interface (RS901 MODEL ONLY) Passive Starter Disable Horn Chirps on remote start ON or OFF Lock During and After Remote Start Abort Tan Wire Output function “Wake up”...
- Page 17 PROGRAMMABLE OPTIONS CHART CONTINUED Diesel Glow Plug Delay Remote Start Engine Run Time Smart Tachless Voltage Adjust 80-100% (Only when Option #1 is set to “Tachless”) Option reset OPTION DESCRIPTIONS: 1. Engine Monitoring: This option sets how the unit monitors your engine. You can program either for Tach mode in which the unit uses a Tach signal (RPM) or for Tachless mode that monitors voltage level.
- Page 18 PROGRAMMABLE OPTIONS 5. OEM Interface (RS901 Add-on Model): This option controls this input selection for the Green Negative Start Trigger Wire. When using an Aftermarket Host Alarm or Keyless Entry System: Leave the setting as “1 pulse” and connect the Green wire to the (-) Auxiliary output wire of the Alarm or Keyless Entry System.
- Page 19 PROGRAMMABLE OPTIONS 13. Horn Chirp Confirmation with Double Lock/Unlock Press (When Optional Horn Output installed): This option allows the system to chirp the vehicle horn for Lock/Unlock confirmation when the Lock or Unlock Button on the remote is pressed a 2nd time within 3 seconds. The horn output must be connected to use this feature. 14.
-
Page 20: Transmitter / Transceiver Programming
900 VI TRANSMITTER / 999FM TRANSCEIVER CODE LEARNING Transmitter/Transceiver Code Learning: (Excludes RS901 model without remotes) Note: Remote Transmitters/Transceivers come pre-programmed from the Factory. When re-learning remotes or adding remotes, ALL your system’s remote codes must be learned at time of programming!! These systems allow storage of up to 4 different remote codes in memory. -
Page 21: Vehicle Operation
2-VEHICLE OPERATION Both the RS-900 VI and RS-999FM systems can be used for 2-car operation. A single RS900VI remote can control two independent vehicles with RS900 VI systems installed. A single RS-999FM transceiver remote can operate two independent cars with RS-999FM systems installed. NOTE: These systems ARE NOT interchangeable. -
Page 22: Troubleshooting "Before You Call" Section
TROUBLESHOOTING: “BEFORE YOU CALL” SECTION UNIT WILL NOT ATTEMPT A START (KEYLESS ENTRY FUNCTIONS NORMALLY): The unit is in Valet mode. Turn IGN ON, press and hold valet/programming button for about 6 seconds then turn key off. Unit is now out of valet mode and should perform a remote start. If optional LED is installed, then it will be on solid when in Valet. -
Page 23: Jumper Pin, Antenna, & System Diagrams
Jumper pins are used to change/configure the operation of the on board multi-function output PINK/WHITE wire, the Parking Light WHITE wire and the PINK glow plug input wire. See the diagrams below for Jumper Pin configurations. CONTROL MODULE JP1 JUMPERS: IGN2 / ACC2 / STR2 PINK WHITE JUMPER PIN DIAGRAMS... - Page 24 ANTENNA DIAGRAM ANTENNA LOCATIONS WINDSHIELD White Plug RS-900 V RS-999FM Black Plug...
- Page 25 TRANSMISSION ENGINE START #2 JUMPER STARTER SELECT (See page 23) +/- PARKING LIGHT JUMPER RS900/901 SERIES (See page ) ANTENNA/RECEIVER PLUG (OPTIONAL) (-) UNLOCK OUTPUT PROGRAM +12 V FOR RELAYS SWITCH (-) LOCK OUTPUT FUEL A/C - HEAT PUMP CONTROL (Only if necessary) BROWN GRAY...
- Page 26 CRIMESTOPPER INSTALLATION ACCESSORIES Crimestopper Security Products Inc. manufactures installation accessories, Databus interface modules and transponder override modules for remote start installation. Relays & Modules: XX-402A/SRS: 30A Relay/Single Relay Socket Transponder Override Module: RS-TATA: Universal Transponder Bypass Module (Requires use of a spare vehicle key) Transponder Override Modules (No Spare Key Required): PKG4: GM PassKey®...
- Page 27 CRIMESTOPPER INSTALLATION ACCESSORIES Databus Door Lock Interface Modules (Allows easy interface into Factory Databus type door lock systems): CHDL-1B: Chrysler Door Lock Interface Module • Lock/Unlock, Factory Alarm Arm/Disarm, Parking Lights, Starter Enable, & Panic • Power Sliding Door/Hatch Input controls, & Door Trigger Output for Aftermarket Alarm Chrysler: Town &...
- Page 28 • Lock/Unlock, Factory Alarm Arm/Disarm, Trunk, & Panic Chrysler: Neon 2002-03, PT Cruiser 2002-03, www.crimestopper.com email@crimestopper.com Phone (800) 998-6880 FAX (805) 581-9500 © 2003 Crimestopper Security Products Dodge: Caravan 2002 Dodge: Intrepid 2002, Stratus 2002 Dodge: Dakota 2002-03, Durango 2002-03, Ram 2002-03 ONLINE TECHNICAL SUPPORT www.crimestopper.com/techweb03.html...