Denon AVR-2113CI Owner's Manual page 106

Audio Delay
While viewing video, manually adjust the time to delay audio output.
0ms – 200ms
• This item can be set within the range of 0 to 100 ms when "Auto Lip Sync" (vpage 106) is set to
"On" and when a TV compatible with Auto Lip Sync is connected.
• Store "Audio Delay" for each input source.
• Audio Delay for game mode can be set when "Video Mode"
"Game".
Volume
Set the MAIN ZONE (room where the unit is located) volume setting.
Setting items
Scale 0 – 98 : Display in the range 0 (Min) to 98.
Set how volume is –79.5dB – 18.0dB : Display ---dB (Min), in the range –79.5 dB to 18.0 dB.
displayed.
• The "Scale" setting is applied also to the "Limit" and "Power On Level"
display method.
• The "Scale" setting applies to all zones.
Limit Off : Do not set a maximum volume.
Make a setting for 60 (–20dB) / 70 (–10dB) / 80 (0dB)
maximum volume.
Power On Level Last : Use the memorized setting from the last session.
Define the volume setting Mute : Always use the muting on condition when power is turned on.
that is active when the 1 – 98 (–79dB – 18dB) : The volume is adjusted to the set level.
power is turned on.
Mute Level Full : The sound is muted entirely.
Set the amount of –40dB : The sound is attenuated by 40 dB down.
–20dB : The sound is attenuated by 20 dB down.
attenuation when muting
is on.
DVD
Default settings are underlined.
Setting details
(vpage 107) is set to "Auto" or
Default settings are underlined.
Setting details
Audyssey
Set Audyssey MultEQ ® XT, Audyssey Dynamic EQ ® and Audyssey Dynamic Volume ® . These can be
selected after Audyssey ® Setup has been performed. For additional information on Audyssey technology,
please see page 141.
NOTE
• If you have not performed Auto Setup, or if you change the speaker settings after performing Auto Setup,
you may not be able to select Dynamic EQ/Dynamic Volume.
In this case, either perform Audyssey ® Setup over again or perform "Restore..."
return to the settings after Audyssey ® Setup was run.
• When HD Audio for which the sampling frequency exceeds 96 kHz is played back, the "Audyssey"
cannot be set.
Setting items
MultEQ ® XT
Audyssey : Optimize the frequency response of all speakers.
MultEQ ® XT compensates
Audyssey Byp.L/R : Optimize frequency response of speakers except
for both time and front L and R speakers.
frequency characteristics Audyssey Flat : Optimize frequency response of all speakers to flat
of the listening area based response.
on Audyssey ® Setup
Graphic EQ : Apply frequency response set with "Graphic EQ"
measurement results. (vpage 104).
Off : Turn "MultEQ ® XT" equalizer off.
Selection is done from three
types of compensation
curves. We recommend the
• "Audyssey", "Audyssey Byp. L/R" and "Audyssey Flat" can be
"Audyssey" setting.
selected after Audyssey ® Setup has been performed. "Audyssey"
MultEQ ® XT is the
is automatically selected after performing Audyssey ® Setup. When
prerequisite function for
"Audyssey", "Audyssey Byp. L/R" or "Audyssey Flat" is selected,
Dynamic EQ and Dynamic
Volume.
• After running Audyssey ® Setup, if the Speaker Configuration, Distance,
Channel Level, and Crossover Frequency have changed without
increasing the number of speakers measured, only
NOTE
When using headphones, "MultEQ ® XT" is automatically set to "Off".
"MultEQ ® XT", "Dynamic EQ" and "Dynamic Volume" settings are stored for each input source.
103
Default settings are underlined.
Setting details
illuminates.
v See overleaf
Audio
(vpage 30) to
illuminates.