fully Jarvis Assembly Instructions Manual
Crank-powered standing desk
Hide thumbs
Also See for Jarvis:
- Assembly instructions manual (29 pages) ,
- Quick start manual (9 pages) ,
- Assembly and use instructions (8 pages)
Subscribe to Our Youtube Channel
Related Manuals for fully Jarvis
Summary of Contents for fully Jarvis
- Page 1 Jarvis crank-powered standing desk Assembly instructions For assembly assistance, call 888-508-3725 or email support@fully.com...
- Page 2 Thank you for choosing a Jarvis desk from Fully.
-
Page 3: Before Starting
Cautions and Use Before starting In the box Assembly Using your own desk top Laying it out Contact... - Page 4 Take all of the items out on a padded or carpeted area to confirm that nothing is missing as displayed on page 2 Tools 4mm Hex Key 3mm Hex Key 2.5 mm Hex Key 6mm Wrench #2 Phillips Screwdriver (not included) Jarvis is a registered trademark of Fully, LLC. All rights reserved.
- Page 5 Jarvis crank-powered standing desk A— Left Lifting Column B— Right Lifting Column C— Feet x2 D— Left Side Bracket E— Right Side Bracket F— Frame Ends x2 G— Center Rails x2 H— Hand Crank I— Right Side Crank Rod J— Left Side Crank Rod K—...
- Page 6 Assembly Step 1 Insert the Left Lifting Column into the Frame End as shown below. To secure the Frame End to the Left Lifting Column, thread four (4) of the Medium Machine Screws into the holes as shown, but do not tighten them all the way. A—...
- Page 7 Important If your Jarvis Desk Top’s pre-drilled holes have metal inserts, you will need to use the Machine Screws packaged with the Jarvis Desk Top to secure the frame. Desk Top Machine Screw x5 Otherwise use five (5) Wood Screws to attach the leg assembly to the desk top.
- Page 8 Once they are in place, tighten them all completely. Important Desk Top Machine Screw x5 If your Jarvis Desk Top’s pre-drilled holes have metal inserts, you will need to use (Included with Jarvis Desk Top) the Machine Screws packaged with the Jarvis Desk Top to secure the frame.
- Page 9 Step 7 Center the labeled midpoints on both Center Rails between the two Frame Ends, and use eight (8) of the Medium Set Screws to lock the Center Rails down firmly. U— Medium Set Screw x8 (Pre-Installed) Warning Skipping this step will result in stability issues.
- Page 10 Step 9 Place the assembled driveshaft between the two rod ends extending from the Lifting Columns. Slide the sleeves onto these rod ends completely, and make sure all Set Screws are facing up and in line with each other as shown below. Once the driveshaft is installed on both sides, tighten all four Set Screws to lock them in place.
- Page 11 A— Left Lifting Column Using the two (2) Wood Screws, attach the Adapter Plate making sure that the “R” or “L” label matches your chosen orientation. If you have a Jarvis Desk Top, use the widely-spaced pre-drilled holes for this purpose.
- Page 12 Step 11 Slide a Crank Washer, then the Crank Spring itself, then the second washer onto the crank rod, as shown. P—Crank Washer x2 O— Crank Spring Step 12 Orient the Crank Sleeve so that its Set Screw is closest to the leg and pointing up, and slide it onto the Crank Rod.
- Page 13 Step 13 Attach the plastic crank bushing to the Adapter Plate using the two (2) Small Socket Headscrews. N— Adapter Plate T— Small Socket-Head Screw x2 Step 14 Loosely attach the Feet to the bottom of the lifting columns with four (4) Medium Machine Screws per foot.
- Page 14 Step 15 Double check that all screws everywhere on the desk are tight. Step 16 With a friend, lift the desk and carefully flip it onto its feet, being careful not to put weight on the hand crank. Then adjust the pre-installed leveling glides on the feet as needed.
- Page 15 Using your own desk top Top size limits: Minimum: 48” x 30” Maximum: 70” x 30” Please use the following guidelines to properly fit your frame to your desk top, and ensure proper clearance for the crank mechanism. Side-to-Side Position: In our experience, desks have the best side-to-side stability when their legs are installed as far apart as possible.
- Page 16 Laying it out The easiest way to position your own desktop on Jarvis is to partially assemble the frame and use it as a template. This partial assembly is easier to maneuver than the entire frame and will allow you to see exactly how things line up and where all the holes should be.
- Page 17 1” of top overhang. Indent the center point of each hole with the tip of a Phillips-head screwdriver, as before. Disassemble the frame components and return to the standard assembly instructions on page 3. Contact Fully Portland, Oregon 888-508-3725 support@fully.com www.fully.com...
- Page 18 Desk, chairs & things to keep you moving 90.014.01.0499 v.G...
Need help?
Do you have a question about the Jarvis and is the answer not in the manual?
Questions and answers
how do I reset