Page 2
For immediate service on any Laguna Tools products: +1 (949) 474-1200 customerservice@lagunatools.com Laguna Tools, Inc. LAGUNA® and the LAGUNA Logo® are the registered trademarks of Laguna Tools, Inc. All rights reserved. 04/01/2019 LAGUNA AMERICAN HEADQUARTERS Texas: 744 Refuge Way Suite 200, Grand Prairie, Texas 75050, U.S.A. Phone: +1-800-332-4094 Huntington Beach: 7291 Heil Ave Huntington Beach, CA 92647, U.S.A.
PX|20 Sheartec:II Planer \ Safety Safety Read and understand all warnings and operation instructions before using any tool or equipment. Always follow basic safety precautions to reduce the risk of personal injury. Improper operation, maintenance or modification of tools or equipment could result in serious injury and property damage. There are certain applications for which tools and equipment are designed.
Page 5
PX|20 Sheartec:II Planer \ Safety PROP 65 WARNING SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER CONSTRUCTION ACTIVITIES CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM. SOME EXAMPLES OF THESE CHEMICALS ARE: ·...
Page 6
PX|20 Sheartec:II Planer \ Safety WEARING PROPER APPAREL. Do not wear clothing, apparel or jewelry that can become entangled in moving parts. Always tie back or cover long hair. Wear non-slip footwear to reduce risk of slipping and losing control or accidentally contacting cutting tool or moving parts.
PX|20 Sheartec:II Planer \ Electrical Safety Electrical Safety WARNING! · RUNNING ON A DIFFERENT VOLTAGE THAN STATED BELOW WILL DAMAGE THE MACHINE. NEVER RUN THE MACHINE IN WET OR DAMP CONDITIONS. · ELECTROCUTION, FIRE, SHOCK, OR EQUIPMENT DAMAGE MAY OCCUR IF MACHINE IS NOT PROPERLY GROUNDED AND CONNECTED TO POWER SUPPLY.
Page 8
PX|20 Sheartec:II Planer \ Electrical Safety Grounding Methods DANGER! THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM ELECTRIC SHOCK. IN ALL CASES, MAKE CERTAIN THAT THE RECEPTACLE IN QUESTION IS PROPERLY GROUNDED. IF YOU ARE NOT SURE, HAVE A QUALIFIED ELECTRICIAN CHECK THE RECEPTACLE.
Page 9
PX|20 Sheartec:II Planer \ Electrical Safety Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded. Use only 3-wire extension cords that have 3-prong grounding plugs and 3 pole receptacles that accept the tool's plug.
Page 10
PX|20 Sheartec:II Planer \ Electrical Safety Extension Cords Use proper extension cords. Make sure your extension cord is in good condition and is a 3- wire extension cord which has a 3-prong grounding type plug and matching receptacle which will accept the machine’s plug.
PX|20 Sheartec:II Planer \ Machine Overview Machine Overview PX|20 Sheartec:II Planer Figure 6: Main Components of PX20 A. Emergency Stop (E-STOP); stops all functions of machine, however, power continues to machine. NOTICE! To reset E-STOP, rotate switch clockwise until the button “pops” out. B.
Page 13
PX|20 Sheartec:II Planer \ Machine Overview Extension Rollers Adjustable rollers that extend for increased workpiece support. Feed Speed Selector CAUTION! AS WITH ALL GEAR BOX SHIFTERS, IT IS VERY IMPORTANT TO ONLY CHANGE SPEEDS WHEN THE MACHINE IS RUNNING. The feed speed selector offers two feed speeds, 16 FPM & 28 FPM. Move lever (push/pull) until it locks in place.
ALL SHIPPING DAMAGE MUST BE NOTED UPON DELIVERY AND SIGNED BY THE OWNER AND THE DELIVERY DRIVER. IF YOU FIND ANY DAMAGED ITEMS IN YOUR PACKAGE, YOU MUST CONTACT LAGUNA TOOLS TO FILE A COMPLAINT. IN ORDER TO RETURN DAMAGED GOODS UNDER THE LIMITED WARRANTY TO LAGUNA TOOLS, INC., YOU MUST HAVE THE ORIGINAL PACKAGING.
Page 15
PX|20 Sheartec:II Planer \ Setup Placement & Unboxing 5. Locate it close to a power source and dust collection. 6. Allow an area for the storage of blanks, finished products and tools. Unboxing WARNING! · THE MACHINE WEIGHS 638 LBS (289KG). ENSURE THAT YOU HAVE ENOUGH PEOPLE TO DO THE JOB SAFELY. ·...
PX|20 Sheartec:II Planer \ Setup Inventory List Inventory List The following depicts items shipped with your machine. Before assembling, ensure that you have received all parts shown below. Machine parts should arrive sealed in plastic bags. Remove parts from plastic bags before laying them out to inventory them.
PX|20 Sheartec:II Planer \ Setup Assembling Assembling Machine Preparation and Setup: 1. Level machine using the four leveling feet on each of the four corners. Lock leveling feet into position with the nut on the leveling foot stud (Fig. 3). FIGURE 3: LEVELING FEET (OPTIONAL) If Installing Unverisal Casters Installing universal caster set (Fig.
Page 18
PX|20 Sheartec:II Planer \ Setup Assembling 2. 2. Clean all rust protected surfaces with a commercial de-greaser. DO NOT use acetone, gasoline, lacquer thinner or any type of cleaner that could damage paint. Coat cleaned surfaces with WD-40® or 20W machine oil. 3.
Page 19
PX|20 Sheartec:II Planer \ Setup Assembling Power Supply Circuit Requirements The power source circuit for your machine must be grounded and rated for the amperage given below. Never replace a circuit breaker on an existing circuit with one of higher amperage without consulting a qualified electrician to ensure compliance with wiring codes.
Page 20
PX|20 Sheartec:II Planer \ Setup Assembling Calibrating the Thickness Scale NOTICE! The following procedures describe the use of a “calibrating board”. It is a piece of hardwood which has been surfaced on one side with a jointer, drum sander or wide belt sander. 1.
Page 21
PX|20 Sheartec:II Planer \ Setup Assembling Calibrating the DRO (Digital Read Out) 1. Remove the battery cover of the DRO and install 2 AAA batteries. FIGURE 9: DRO BATTERIES DRO Button Reference and Use It is helpful to familiarize these buttons and their purpose with the Wixey™ DRO...
PX|20 Sheartec:II Planer \ Operation Operation CAUTION! PLACE THE PLANER ON A SECURE AND STABLE SURFACE FOR OPERATION. CLAMP OR BOLT THE PLANER INTO POSITION. 1. Establish the proper depth of cut (typically less than 1/16”), using either the DRO or scale. 2.
PX|20 Sheartec:II Planer \ Maintenance Maintenance General Keep your machine clean. At the end of each day, clean the machine. Wood contains moisture, and if sawdust or wood chips are not removed they will cause rust. In general, we recommend that you only use a Teflon-based lubricant on the planer. Regular oil attracts dust and dirt.
Page 25
PX|20 Sheartec:II Planer \ Maintenance Sheartec II Knife rotation/replacement CAUTION! KNIFE INSERTS ARE DANGEROUSLY SHARP. USE EXTREME CAUTION WHEN INSPECTING, REMOVING, OR REPLACING KNIFE INSERTS. WARNING · TURN PLANER OFF AND DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE OR ADJUSTMENTS! · MAKE SURE ALL KNIFE INSERT SCREWS ARE TIGHTENED SECURELY.
Page 26
PX|20 Sheartec:II Planer \ Maintenance Conveying Rollers WARNING · TURN PLANER OFF AND DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE OR ADJUSTMENTS! MAINTENANCE: Keep rollers clean to help prevent slippage of material. Be careful not to contact cutterhead knives as they are very sharp! ADJUSTMENTS: The planer comes set-up from the factory and typically will not need adjustment.
Page 27
PX|20 Sheartec:II Planer \ Maintenance Anti-Kickback Fingers WARNING · TURN PLANER OFF AND DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE OR ADJUSTMENTS! Anti-kickback fingers help prevent stock from being kicked out of the machine towards the user. Keep the fingers clean and free from sawdust, pitch gum, etc., so they operate smoothly.
Page 28
PX|20 Sheartec:II Planer \ Maintenance Adjustment of Pressure Bar WARNING · TURN PLANER OFF AND DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE OR ADJUSTMENTS! The pressure bar should be set even with the lowest point of knife. Make sure the knives are set properly see the “Setting / Changing Knives”...
Page 29
PX|20 Sheartec:II Planer \ Maintenance 1. Disconnect machine from power source. 2. Place a hard wood gauge (Fig.17, A) under a knife in the cutterhead. Place a 0.02” feeler gauge (Fig. 17, B) on top of wood block and raise table until the gauge contacts the knife in its lowest position.
Page 30
PX|20 Sheartec:II Planer \ Maintenance Poly-V-Belt Adjustment WARNING · TURN PLANER OFF AND DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE OR ADJUSTMENTS! Poly-V-belt (Fig. 22, D) tension has been set at the factory. If the belt has stretched and needs adjustment. 1.
Page 31
PX|20 Sheartec:II Planer \ Maintenance Adjusting Table Rollers WARNING · TURN PLANER OFF AND DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE OR ADJUSTMENTS! The table rollers come pre-set from the factory and shouldn’t need any adjustment. If adjustment is necessary, follow the below listed steps. 1.
PX|20 Sheartec:II Planer \ Lubrication Lubrication Regular monitoring and replacement of lubrication is needed. Figure 25 Table POSITION GREASE GEAR BOX CHAIN CHAIN CHAIN CHAIN BUSHING LEAD SCREW FIGURE 25: LUBRICATION FIGURE 26: LUBRICATION · The Gear Box oil must be changed after 2500 hours of work.
PX|20 Sheartec:II Planer \ Troubleshooting Troubleshooting Symptom Possible Cause Possible Solution Machine will not 1. Fuse blown or circuit breaker tripped 1. Replace fuse or reset circuit breaker start 2. Cord damaged 2. Have cord replaced 3. Not connected to power source 3.
PX|20 Sheartec:II Planer \ Wiring Wiring WARNING REVIEW ELECTRICAL SAFETY PRIOR TO ANY WIRING PROCEDURES. MPLANPX20-0130 VOLTAGE 220V PHASE HERTZ 60Hz FULL LOAD AMPERAGE 23 AMPS Below are RECOMMENDATIONS to be used for this machine based on the above information. Variables that may affect this are: ·...
Page 43
PX|20 Sheartec:II Planer \ Replacement Parts Table REF NO PART NUMBER DESCRIPTION SPECIFICATION 150016-000 LIFTING SPROCKET 170746-901 TEETH WASHER 130094-903 LOCK NUT 360413-901 FIXING PIN 174836-000 BASE CASTING 010014-000 RETAINING RING STW-35 938011-000 MAGNETIC SWITCH ASSEMBLY 5HP*220V-240V*1PH*CSA 000801-108 ROUND HEAD HEX SCREW M6*1.0P*8 174845-000 BASE REAR COVER...
Page 44
PX|20 Sheartec:II Planer \ Replacement Parts Table REF NO PART NUMBER DESCRIPTION SPECIFICATION 000203-104 SET SCREW M6*1.0P*12 010208-000 RETAINING RING ETW-12 361385-902 SUPPORT ROD 050287-008 MOTOR PLATE 380148-000 ADJUSTABLE ROD 008007-100 HEX. NUT M10*1.5P(17B*8H) 006003-091 FLAT WASHER 13*28*3.0T 000003-108 HEX. SCREW M8*1.25P*40 006001-041 FLAT WASHER...
This machine is covered by a warranty and the purchasing dealer can answer any questions you may have. Additionally, you can contact Laguna: +1 (949) 474-1200 customerservice@lagunatools.com. Every product sold is warranted to be free of manufacturers’ defective workmanship, parts, and materials.