Download Print this page
Deagostini MODEL SPACE Honda CB750 FOUR Assembly Manual

Deagostini MODEL SPACE Honda CB750 FOUR Assembly Manual

Pack 18
Hide thumbs Also See for MODEL SPACE Honda CB750 FOUR:

Advertisement

Quick Links

BUILD YOUR OWN
TM
Pack 18
01

Advertisement

loading
Need help?

Need help?

Do you have a question about the MODEL SPACE Honda CB750 FOUR and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Deagostini MODEL SPACE Honda CB750 FOUR

  • Page 1 BUILD YOUR OWN Pack 18...
  • Page 2 CONTENTS Assembly Guide Stage 57: The rear fender and battery box Stage 58: The centre stand Stage 59: The exhausts Editorial and design by Continuo Creative, 39-41 North Road, London N7 9DP. Published in the UK by De Agostini UK Ltd, Battersea Studios 2, 82 Silverthorne Road, London SW8 3HE.
  • Page 3 Honda CB750 FOUR: Assembly Guide Stage 57 The rear fender and battery box Prepare the main frame assembly from Stage 55 and undo the nut at the end of the pivot shaft. Remove the left frame half from Your parts the assembly.
  • Page 4 Honda CB750 FOUR: Assembly Guide Hold the battery box as shown, with the Take the cables from the IR sensor, the three circled tabs facing towards you. rear brake and the kick starter, and position them in the same hole as the battery box cable.
  • Page 5 Honda CB750 FOUR: Assembly Guide Tighten the type E screw from Stage 32 When tightening the type Q screw, you into the hole at the front of the left frame may find that the cross wrench hits the half, to join the front ends of the two transmission case cover.
  • Page 6 Honda CB750 FOUR: Assembly Guide Hold the cables in position and then place a wire Work along the rear fender, fitting two more wire holder (Stage 34) over them, inserting the projections holders to the fender. (circled) on the underside of the rear fender into the holes in the holder.
  • Page 7 Honda CB750 FOUR: Assembly Guide Pass the three cables through the hole above Pull the three cables through the frame, just behind the air filter. the air filter. Stage complete Gently pull the three cables through the hole as far as they will go.
  • Page 8 Honda CB750 FOUR: Assembly Guide Stage 58 The centre stand Take the main frame assembly and turn it over. Remove the masking tape holding the centre stand spring. To make the following steps easier, it is best to remove the spring from Your parts the stand.
  • Page 9 Honda CB750 FOUR: Assembly Guide Use the type E screw to tap the hole, Pass a type E screw into the looped end Hold the spring next to the frame, as screwing it in for about two thirds of the spring. shown, and tighten the type E screw into of its thread length, then remove it.
  • Page 10 Honda CB750 FOUR: Assembly Guide Hold the stand down so that it’s in line Pivot the stand forward until it’s at about If the stand doesn’t operate properly, Take the battery box cover and remove with the bottom of the frame. This is a right angle to the frame.
  • Page 11 Honda CB750 FOUR: Assembly Guide Take the dynamo cover and place it into the circular Tighten the type M screw into place. recess in the side of the transmission case cover. Take a type M screw and insert it into the hole at the top of the dynamo cover.
  • Page 12 Honda CB750 FOUR: Assembly Guide Stage 59 STEP The exhausts Left exhaust assembly Prepare the exhaust assemblies from Stages 17 and 21. Right exhaust assembly Your parts Base frame 4 Control board Screws (type G) × 5 Joint C 4 × 9mm screws with washers × 4 Insert a type J screw (Stage 49) into the circled hole in the centre of one of the exhaust assemblies.
  • Page 13 Honda CB750 FOUR: Assembly Guide Remove the screw from the tapped hole (circled), Turn the main frame assembly over, and align the two and then tap the corresponding hole in the other pins on the exhaust pipe joint with the indicated holes in exhaust assembly.
  • Page 14 Honda CB750 FOUR: Assembly Guide Holes Insert the exhaust pipes into the two right-hand Insert the pin into the hole, and align the adjacent exhaust pipe joints. holes of the silencers and the frame. Align the central section of the silencers with the circled area of the frame.
  • Page 15 Honda CB750 FOUR: Assembly Guide Position the two exhaust pipes on either side of the Insert the pin into the hole and align the holes of the Insert a type J screw into the aligned holes of the frame at the circled point. silencers and the frame, as in Step 12.
  • Page 16 Honda CB750 FOUR:...