HIKOKI DH 18DPC Handling Instructions Manual
  1. Manuals
  2. Brands
  3. HIKOKI Manuals
  4. Rotary Hammer
  5. DH 18DPC
  6. Handling instructions manual

HIKOKI DH 18DPC Handling Instructions Manual

Hide thumbs Also See for DH 18DPC:
Table of Contents

Advertisement

Quick Links

Download this manual
DH 18DPC
Handling instructions

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DH 18DPC and is the answer not in the manual?

Questions and answers

Related Manuals for HIKOKI DH 18DPC

Summary of Contents for HIKOKI DH 18DPC

  • Page 1 DH 18DPC Handling instructions...
  • Page 5 950 /min 3170 4300...

  • Page 6: General Power Tool Safety Warnings

    power source and/or battery pack, picking up or GENERAL POWER TOOL SAFETY carrying the tool. WARNINGS Carrying power tools with your fi nger on the switch or energising power tools that have the switch on WARNING invites accidents. Read all safety warnings and all instructions. d) Remove any adjusting key or wrench before Failure to follow the warnings and instructions may result in turning the power tool on.

  • Page 7: Cordless Rotary Hammer Safety Warnings

    c) When battery pack is not in use, keep it away 10. Do not touch the bit during or immediately after from other metal objects, like paper clips, coins, operation. The bit becomes very hot during operation keys, nails, screws or other small metal objects, and could cause serious burns.

  • Page 8: Regarding Lithium-Ion Battery Transportation

    2. If the tool is overloaded, the motor may stop. In this ○ To prevent shorting from occurring, load the battery in case, release the switch of tool and eliminate causes of the tool or insert securely the battery cover for storing overloading.

  • Page 9: Standard Accessories

    *1 Specifi cations are for when a dust extractor system has Full-load impact rate been installed. φ Drilling diameter, max. NOTE Due to HiKOKI’s continuing program of research and Weight* development, the specifi cations herein are subject to change without prior notice. Concrete CHARGING Steel Before using the power tool, charge the battery as follows.
  • Page 10 Table 1 Indications of the pilot lamp Lights for 0.5 seconds. Does not light for 0.5 Before Blinks seconds. (off for 0.5 seconds) charging Lights continuously While charging Lights Lights for 0.5 seconds. Does not light for 0.5 Charging Blinks seconds.

  • Page 11: Mounting And Operation

    ○ When the pilot lamp fl ickers in red (at 0.2-seconds AUTO STOP FUNCTION intervals), check for and take out any foreign objects in the charger’s battery connector. If there are no foreign In selection mode, pressing the button for longer than two objects, it is probable that the battery or charger is seconds will move to memory mode.

  • Page 12: Maintenance And Inspection

    NOTE Despite taking steps to correct a problem, the display lamp may continue to blink. Should this be the case, the unit may require repair. If so, please contact the outlet from which this product was purchased for repairs. LUBRICATION This Rotary Hammer is of full air-tight construction to protect against dust and to prevent lubricant leakage.

  • Page 13: Troubleshooting

    NOTE country must be observed. Storing lithium-ion batteries. Make sure the lithium-ion batteries have been fully Important notice on the batteries for the HiKOKI charged before storing them. cordless power tools Prolonged storage (3 months or more) of batteries with...
  • Page 14 DH18DPC DH18DPC 18 V 0–950 /min 0–4300 /min 26 mm 20 mm φ max 13 mm – φ max 27 mm – φ max 3.2–3.8 kg 4.3–4.9 kg DH18DPC...
  • Page 15 335273 303709 376759 BSL18.. BSL36..18 UC18YFSL (14.4 V–18 V) 329897 337528 376763 376971 336471 376764 376972...
  • Page 16 971787 306885 1: 303617 944477 2: 303618 A: 303619 B: 303620 (A) 105 mm: 303625 (A): 982684 300 mm: 303626 (B): 982685 (B) 300 mm: 303627 303332 12.7 mm: 303044 19 mm: 303045 316656 303046 316657 316658 DH18DPC (When the dust extractor system is removed) 316659...
  • Page 20 Shinagawa Intercity Tower A, 15-1, Konan 2-chome, Minato-ku, Tokyo, Japan Code No. C99741911 F Printed in China...

Table of Contents