c) Prevent unintentional starting. Ensure the GENERAL POWER TOOL SAFETY switch is in the off -position before connecting WARNINGS to power source and/or battery pack, picking up or carrying the tool. WARNING Carrying power tools with your fi nger on the switch Read all safety warnings, instructions, illustrations and or energising power tools that have the switch on specifi...
5) Battery tool use and care 2) Safety instructions when using long drill bits with a) Recharge only with the charger specifi ed by the rotary hammers manufacturer. a) Always start drilling at low speed and with the A charger that is suitable for one type of battery pack bit tip in contact with the workpiece.
17. Rotation + hammering 2. Do not pierce battery with a sharp object such as a When the drill bit touches construction iron bar, the bit nail, strike with a hammer, step on, throw or subject the will stop immediately and the rotary hammer will react battery to severe physical shock.
Page 10
SYMBOLS Power Output WARNING The following show symbols used for the machine. Be sure that you understand their meaning before 2 to 3 digit number use. DH18DPC: Cordless Rotary Hammer To reduce the risk of injury, user must read instruction manual. NAMES OF PARTS (Fig.
17. *1 Specifi cations are for when a dust extractor system has been installed. NOTE Due to HiKOKI’s continuing program of research and development, the specifi cations herein are subject to change without prior notice. Table 1 Indications of the pilot lamp Lights for 0.5 seconds.
● Regarding the temperatures and charging time of the battery. The temperatures and charging time will become as shown in Table 2. Table 2 Charger UC18YFSL Type of battery Li-ion Temperatures at which the 0°C–50°C battery can be recharged Charging voltage 14.4 Multi volt BSL14xx series...
REACTIVE FORCE CONTROL Adjusting the drilling depth Changing the chisel position This product is equipped with a Reactive Force Control (RFC) feature that reduces jerking of the tool body. Switch operation If the tool bit is suddenly overburdened, any jerking of the Setting the speed tool body is reduced by activation of the slip clutch or by stopping of the motor by the sensor built into the tool body.
ABOUT THE PROTECTION MAINTENANCE AND INSPECTION FUNCTION WARNING Be sure to turned off the switch and remove the battery This tool has a built-in protection circuit for preventing before maintenance and inspection. damage to the unit in the event of an abnormality. Depending 1.
Page 15
Important notice on the batteries for the HiKOKI cordless power tools Please always use one of our designated genuine batteries. We cannot guarantee the safety and performance of our cordless power tool when used with batteries other than these designated by us, or when the battery is disassembled and modifi...
TROUBLESHOOTING Use the inspections in the table below if the tool does not operate normally. If this does not remedy the problem, consult your dealer or the HiKOKI Authorized Service Center. Symptom Possible cause Remedy Tool doesn’t run No remaining battery power Charge the battery.
Page 17
DH18DPC DH18DPC* 18 V 0–950 min 0–4300 min 26 mm 20 mm φ max 13 mm – φ max 27 mm – φ max 3.2–3.8 kg 4.3–4.9 kg BSL1850 UC18YFSL DH18DPC 2JAS – – – – – – – –...
Page 21
English Dansk Română GUARANTEE CERTIFICATE GARANTIBEVIS CERTIFICAT DE GARANŢIE Model No. Modelnummer Model nr. Serial No. Serienummer Nr. de serie Date of Purchase Købsdato Data cumpărării Customer Name and Address Kundes navn og adresse Numele și adresa clientului Dealer Name and Address Forhandlers navn og adresse Numele și adresa distribuitorului (Please stamp dealer name and address)
Page 23
Tel: +32 2 460 1720 URL: http://www.hikoki-powertools.hu Fax: +32 2 460 2542 URL http://www.hikoki-powertools.be Hikoki Power Tools Polska Sp. z o. o. ul. Gierdziejewskiego 1 Hikoki Power Tools Italia S.p.A 02-495 Warszawa, Poland Via Piave 35, 36077, Altavilla Vicentina (VI), Italy...
Page 27
EN IEC 62841-2-6:2020+A11:2020 EN60335-1:2012+A11:2014 EN60335-2-29:2004+A2:2010 EN55014-1:2006+A1:2009+A2:2011 EN55014-2:1997+A1:2001+A2:2008 Representative offi ce in Europe 31. 1. 2023 Hikoki Power Tools Deutschland GmbH Akihisa Yahagi European Standard Manager Siemensring 34, 47877 Willich, Germany 31. 1. 2023 Head offi ce in Japan Koki Holdings Co., Ltd.
Page 28
EN IEC 62841-2-6:2020+A11:2020 EN60335-1:2012+A11:2014 EN60335-2-29:2004+A2:2010 EN55014-1:2006+A1:2009+A2:2011 EN55014-2:1997+A1:2001+A2:2008 Importer and authorized person to compile the technical file Hikoki Power Tools (U.K.) Ltd. 25 Majestic Road, Southampton, SO16 OYT, United Kingdom 31. 1. 2023 Head office in Japan Koki Holdings Co., Ltd.
Need help?
Do you have a question about the DH 18DPC and is the answer not in the manual?
Questions and answers