Advertisement
Q710 – LTE Access Point
Federal Communications Commission Notices
This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this equipment that have not been approved by Ruckus Wireless may void the user's authority to operate this
equipment.
For Class B Equipment:
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—
Reorient or relocate the receiving antenna.
—
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
This device meets all requirements specified in the FCC Part 96 Rules. This transmitter must not be co-located or operate in conjunction with any other
antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated
with minimum distance 20 cm between the radiator & your body.
Safety Notices and National Restrictions
This product is intended to be installed at a restricted access location and is marked with a visible warning
Professionally Installed Products
The product is to be installed according to the installation instructions. The User/Operator does not have access to the device once the device is
installed and in use. Provisions for permanent grounding are provided.
1. Installation personnel: This product is designed for a specific application and is to be installed by qualified personnel with knowledge of RF and
applicable rules. General users are not to attempt installation or changing settings.
2. Installation location: The product is to be installed at a location where the radiating antenna can be kept at least 20 cm from any nearby persons in
normal operation conditions to meet regulatory RF exposure requirement.
3. Installation procedure: Please refer to installation instructions for details.
4. Warning: Please carefully select the installation position and make sure that the final output power does not exceed the limit set forth in US CFR 47
Part 96. Violation of the rule could lead to serious federal penalty.
Products intended to be powered by an external power supply:
Warning –This product is intended to be supplied by a Listed Direct Plug-In Power Unit marked Class 2 or LPS (sub-clause 2.5 of standard EN 60950-
1). Available Ruckus power supplies intended for product operation are identified in the product datasheet. The last two digits of the power supply
part number represent the country code. For additional applicable power supplies/options, see user instructions and product datasheet.
Medical Statement
Ruckus Wireless Access Points shall only be used in ME systems where the intended EM ENVIRONMENT does NOT rely on the Wireless radio link for
BASIC SAFETY or ESSENTIAL PERFORMANCE of the ME SYSTEM.
Ruckus Wireless, Inc.
Ruckus Wireless Inc., an ARRIS Company
— Increase the separation between the equipment and receiver.
— Consult the dealer or an experienced radio/TV technician for help.
350 West Java Drive Sunnyvale, CA 94089 USA
Page 1
that the surface may be hot
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Arris RUCKUS Q710
Summary of Contents for Arris RUCKUS Q710
- Page 1 Page 1 Q710 – LTE Access Point Ruckus Wireless Inc., an ARRIS Company Federal Communications Commission Notices This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
-
Page 2: Key Features And Benefits
• PoE+ and internal BeamFlex™ antennas for Wi-Fi like deployment simplicity ADVANCED TECHNOLOGY • A\racLve design ideal for public venues and private enterprise Q710 s packed with advanced 3GPP and proprietary environments technology, such as LTE-Advanced Carrier AggregaLon, Self-Organizing Networks (SON), Self- Organizing Timing and Zero-Touch Provisioning™ that make the soluLon both extremely powerful as PORT DETAIL well as easy to deploy. WI-FI -LIKE SIMPLICITY Q710 is ideal for in-building LTE wireless networks that deploy with the economics and simplicity of Wi-Fi. ATTRACTIVE DESIGN Q710 looks and feels like a Wi-Fi access point. Its a\racLve design is ideal for hospitality, educaLon, large office, MTU/MDU, retail, public venues and similar environments. It can even be hidden above ceiling Lles or painted to virtually disappear into the environment. Copyright © 2018 Ruckus Networks, an ARRIS company. All rights reserved. -
Page 3: Data Sheet
May require future sopware features Approximate maximum aggregate applicaLon layer uplink and downlink throughput, 4 CBRS channels (40MHz), TDD Config 2, Cat 6 and above UE client Copyright © 2018 Ruckus Networks, an ARRIS company. All rights reserved. No part of this content may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation, or adaptation) without written permission from Ruckus Networks (“Ruckus”). -
Page 4: Mounting Instructions
FIGURE 2 Slide T-bar clip to lock the bracket onto the T- This Quick Setup Guide provides step-by-step instructions on how to set up your Ruckus Q710 LTE Access Point (AP). After completing the steps described in this guide, you will be able to... -
Page 5: Making The Connections
© 2018 ARRIS Enterprises LLC. All rights reserved. ARRIS, the ARRIS logo, Ruckus, Ruckus Wireless, the Ruckus logo, and If using PoE, attach one of the Ethernet cable to an 802.3at Type the Big Dog design are trademarks of ARRIS International plc and/or 2-certified switch or PoE injector (sold separately).
Need help?
Do you have a question about the RUCKUS Q710 and is the answer not in the manual?
Questions and answers