Advertisement
Quick Links
—— Instruction Manual ——
BA832/833/833XL
Portable/Adjustable Basketball Systems
P A R T S L I S T
Item
Qty
Description
A
1
Portable Base and Pole Assembly
B
1
Extension Arm Assembly
C
2
Upper Backboard Support Brackets (BA832/833)
D
2
Lower Backboard Support Brackets (BA832/833)
E
4
Backboard Mounting Angles (BA832/833)
F
8
5/16" X 1" Hex Bolts (BA832/833)
G
12
5/16" Flange Nuts (BA832/833)
H
8
5/16" Flat Washers (BA832/833)
I
1
Height Indicator Labels (attached to base)
Do not release the height adjustment handle or loosen the telescoping pole lockbolt until the system is
completely assembled as the telescoping tubes are under spring tension and may cause damage or injury to
Inspect all contents prior to installation. Report any missing parts to dealer immediately.
Carefully read all instructions before proceeding. Pay special attention to the safety instructions on the next page.
Save this instruction in the event that the manufacturer must be contacted in the future for maintenance
information.
1. This basketball system is shipped partially
preassembled. After removing the system from its
shipping skid open the lower padded front of the
unit by removing the Lock Knob (P) and pulling
forward on the top of the lower pad. Remove the
unassembled parts and hardware. See Figure 1.
2. For BA832/833 open the rear ballast storage
compartment by removing 4 screws. Do not
remove the bottom 2 pivot screws. Pivot rear
cover open and place 12 each 4"x 8"x 16" solid
Concrete CAP Blocks and 3 each 4"x 8"x 8" Solid
Concrete CAP Blocks into the compartment.
Make sure that the weight is evenly distributed.
Reposition the rear cover.
See Layout 1.
Date: 10/19/2020
Rev: 9 B.A.
Item
J
K
L
M
N
O
P
Q
Warning!
the assembler.
Figure 1
N.J.C.
File: \PUB\BA833
1
Customer Service
(800) 247-7668
Qty
Description
1
Acrylic Backboard Hardware (pkg. w/ backboard)
1
Backboard (pkg. separately)
1
Goal (pkg. separately)
1
Goal Mounting Hardware (pkg. separately)
4
5/16" X 1 1/2" Carriage Bolt (BA832)
1
Locking Pin
1
Lock Knob
1
Backboard Mounting H-Frame (BA833XL)
P
Ref#: 930306
Advertisement
Related Manuals for Bison BA832
Summary of Contents for Bison BA832
- Page 1 Remove the unassembled parts and hardware. See Figure 1. 2. For BA832/833 open the rear ballast storage compartment by removing 4 screws. Do not remove the bottom 2 pivot screws. Pivot rear cover open and place 12 each 4”x 8”x 16”...
- Page 2 Hex Bolts (F) and 5/16” Flange Nuts (G). Do not tighten at this time. See Figure 3 & 4. 8. On BA832 systems attach 2 Backboard Mounting Angles (E) to the Backboard (K) using 5/16 x 1 1/2” Carriage Bolts (N), 5/16”...
- Page 3 Warning! The recent popularity of adjustable height basketball systems has increased the risk of dental injury, particularly to young players, due to players getting their teeth caught in the net. GOAL HARDWARE (M) (provided with goal) GOAL (L) EXTENSION ARM ASSEMBLY (B) BACKBOARD (K) BACKBOARD MOUNTING...
- Page 4 Warning! Never use the backboard to push or pull the system as unwarranted backboard breakage will likely occur. 16. To roll the system, unscrew the Lock Knob (P) to release the lower front padding. This will lower the unit to the portable position. To lock in place push padding to the original position and tighten the Lock Knob (P) .