Advertisement
Available languages
Available languages
Quick Links
INSTRUCTIONS FOR CH42A, CH43A, CH44A PNEUMATIC CHIPPING HAMMERS
Read and understand these instructions before operating this tool.
Everyone using, maintaining, changing accessories or working near this tool must read, understand and follow these Safety Instructions!
INTENDED USE
The intended use of this tool is for cleaning, chipping, and chiseling concrete and metal surfaces. Do not use this tool for any other purpose.
AIR SUPPLY
The efficiency of the tool is dependent on the proper supply of clean dry air at 90 psig (6.2 bar). The use of an in-line filter and pressure regulator will insure
maximum output and tool life. Before connecting the tool, blow out the air line to remove water and dirt which may have accumulated.
LUBRICATION
An airline lubricator, set to deliver one drop per minute, is recommended. If a lubricator is not used, add .04 oz (1.2 cc) of Sioux No. 288 air motor oil into
the inlet daily or more frequently if used continuously.
HOSE AND HOSE CONNECTIONS
The supply hose I.D. should not be less than 1/2" (13 mm). Do not use coupling or fitting with a smaller I.D. than the supply hose. When using quick
couplers, install a leader hose between the tool and the quick coupler.
GENERAL OPERATION
Operation
Tools are operated with a trigger throttle on the outside of the handle. Be sure the chisel is against the work piece before depressing the trigger. Release
the trigger to stop the tool.
The chisel is installed or removed by pullling back the front lock ring on the chipper to release the chisel. After installing a chisel, be certain that the lock
ring is detented into position so the chisel is retained.
Never operate the scaler without a chisel because internal damage can occur to the tool.
Always unhook tool from the air supply before changing pistons.
IF THE TOOL LOSES POWER, CHECK THE FOLLOWING:
• Air pressure
Ensure that there is adequate supply of clean, dry air at 90 psig (6.2 bar).
• Chisels
Check for worn and broken chisels.
• Hose size
Ensure that the hoses, couplers, and fittings meet the criteria in "HOSE AND HOSE CONNECTIONS".
• Sluggish or erratic operation
Flush tool out with a small amount of petroleum solvent and operate for a few seconds, then re-lubricate the tool using air motor oil. If the tool still does
not perform correctly it will need to be disassembled and repaired.
Catalog No.
CH42A-H
CH42A-R
CH43A-H
CH43A-R
CH44A-H
CH44A-R
We, Sioux Tools Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, declare under our sole responsibility that the products
to which this declaration relates are in conformity with the following standard or standards or other normative document or documents:
July 1, 2003
Murphy, North Carolina, USA
Date and place of issues
250 Snap-on Drive • PO Box 1596 • Murphy, NC 28906 • USA • Phone: 828-835-9765 •www.siouxtools.com
Form ZCE682
SAVE THESE INSTRUCTIONS!
WARNING
When used improperly power tools can create hazardous situations.
Improperly used power tools can cause injury or death.
SOUND AND VIBRATION READINGS
*Sound Pressure dBA
99.3
99.3
99.3
99.3
99.3
99.3
*per PN8NTC1
DECLARATION OF CONFORMITY
CH42A-H, CH42A-R, CH43A-H, CH43A-R, CH44A-H, CH44A-R
EN 792 (draft), EN 292 Parts 1&2, ISO 8662, Pneurop PN8NTC1
following the provisions of
89/392/EEC as amended by 91/368/EEC & 93/44/EC Directives.
Gerald E. Seebeck
President
Sioux Tools Inc.
Name and position of issuer
Original
Instructions
*Sound Power dBA
110.9
110.9
110.9
110.9
110.9
110.9
*per PN8NTC1
Signature of issuer
1
Form ZCE682
Date 2003July30/B
Page 1 of 8
*Vibration m/s2
27.2
27.2
27.2
27.2
27.2
27.2
*per ISO 8662
Date 2003July30/B
Advertisement
Related Manuals for Sioux Tools CH42A
Summary of Contents for Sioux Tools CH42A
- Page 1 *per ISO 8662 DECLARATION OF CONFORMITY We, Sioux Tools Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, declare under our sole responsibility that the products CH42A-H, CH42A-R, CH43A-H, CH43A-R, CH44A-H, CH44A-R to which this declaration relates are in conformity with the following standard or standards or other normative document or documents: EN 792 (draft), EN 292 Parts 1&2, ISO 8662, Pneurop PN8NTC1...
- Page 2 *per ISO 8662 KONFORMITÄTSERKLÄRUNG Wir, Sioux Tools, Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, erklären hiermit alleinverantwortlich, daß die Produkte CH42A-H, CH42A-R, CH43A-H, CH43A-R, CH44A-H, CH44A-R auf die sich diese Erklärung bezieht, mit den Anforderungen der folgenden Standards oder Normen oder Dokumenten übereinstimmen: EN 792 (Entwurf) EN 292 Teile 1&2, ISO 8662, Pneurop PN8NTC1...
- Page 3 *según PN8NTC1 *según ISO 8662 DECLARACION DE CONFORMIDAD Nosotros, Sioux Tools, Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, declaramos bajo nuestra única responsabilidad que los productos CH42A-H, CH42A-R, CH43A-H, CH43A-R, CH44A-H, CH44A-R con los cuales se relaciona esta declaración están en conformidad con las siguiente(s) norma(s) u otro(s) documento(s) normativo(s): EN 792 (anteproyecto) EN 292 Partes 1&2, ISO 8662, Pneurop PN8NTC1...
- Page 4 *secondo ISO 8662 CERTIFICAZIONE DI CONFORMITA La Sioux Tools, Inc, con sede al 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, solennemente dichiara sotto la propria e sola responsabilità che i prodotti CH42A-H, CH42A-R, CH43A-H, CH43A-R, CH44A-H, CH44A-R...
- Page 5 *selon la norme ISO 8662 DÉCLARATION DE CONFORMITÉ La société Sioux Tools, Inc., située à : 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, affirme que les produits CH42A-H, CH42A-R, CH43A-H, CH43A-R, CH44A-H, CH44A-R dont cette fiche fait l’objet, sont conformes aux normes, documents normatifs et autres références : EN 792 (ébauche) Parties 1 et 2 de la norme EN 292, ISO 8662, Pneurop PN8NTC1...
- Page 6 *conform PN8NTC1 *conform ISO 8662 CONFORMITEITSVERKLARING Ondergetekende, Sioux Tools, Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, verklaart met inachtneming van de eigen aansprakelijkheid desbetreffend, dat de produkten CH42A-H, CH42A-R, CH43A-H, CH43A-R, CH44A-H, CH44A-R waarop deze verklaring van toepassing is, conform zijn met de hierna genoemde norm, normen en/of andere regels en voorschriften:...
- Page 7 *enligt ISO 8662 FÖRSÄKRAN OM ÖVERENSSTÄMMELSE Vi, Sioux Tools, Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, förklarar under eget ansvar att produkterna CH42A-H, CH42A-R, CH43A-H, CH43A-R, CH44A-H, CH44A-R som denna försäkran gäller uppfyller följande standard eller standarder eller andra normgivande dokument:...
- Page 8 WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. WARNUNG Der durch Elektrosanden, -sägen, -schleifen und -bohren sowie durch andere Bauarbeiten anfallende Staub enthält Chemikalien, die nachweislich Krebs sowie Geburts- bzw.
- Page 9 This pdf incorporates the following model numbers: CH42A-H, CH42A-R, CH43A-H, CH43A-R, CH44A-H, CH44A-R...