Exido 246-050 Manual page 24

o The balloon whisk (8) is used for whisking
cream, egg whites, etc.
Turn the accessory, so the pins on the shaft are
aligned with the depressions on the accessory's
top edge. Press the accessory up towards the arm,
turning it at the same time to the right so that the
pins slide into position, thus securely locking the
accessory in place.
The accessory must
not be loose nor
should you be able
to pull it free.
81 Lower the arm so
that it locks into
place with a click.
The lid must fit
tightly onto the
mixing bowl. If not, it
is fitted incorrectly.
91 The appliance is now ready for use.
Whisking, kneading and mixing
11 Connect the appliance. The indicator next to the
OFF button (g) lights up.
21 Start the appliance by pressing one of the five
speed buttons (a-e). Speed 1 (a) is the slowest and
speed 5 (e) is the fastest. Recommended speeds,
time and capacity are shown in the table below.
31 Stop the appliance by pressing the OFF button
if you want to pause, for example to add more
ingredients.
41 If you need to scrape inside the mixing bowl, wait
until the accessory has stopped completely. Use
the spatula, never your fingers.
51 Switch off the appliance by pressing the OFF
button when you have finished mixing. Always
unplug the appliance before you change the
accessories or take the appliance apart.
61 Tilt the arm up using the arm release handle.
71 Dismantle the accessory by turning it to the left.
81 Remove the mixing bowl.
91 Clean all accessories before storing the appliance.
See "Cleaning".
Accessories: Speed
1½ min. at
speed 1
Dough hook 1, 2
and 8 min.
at speed 2
Dough whisk 1, 2, 3 10 min.
Balloon whisk 4, 5 10 min.
Meat grinder 3, 4 10 min.
2 min. on /
Blender 4,5,pulse
2 min. off
USING THE MEAT GRINDER
Assembly
11 Place the motor section on a flat surface, e.g. a
kitchen counter, and make sure it is standing firmly.
21 Check the arm is tilted down and locked into
position and that the cover for the blender opening
has been fitter over the blender opening.
Time Capacity
1,500 g flour and
750 ml water
8 egg whites or
600 ml cream
Max. 1L
24
31 Remove the protective cover from the accessory
socket. Turn the cover so the white triangle is
aligned with the black circle and remove the cover.
41 Place the meat grinder body in the accessory
opening and turn the body to
vertical position.
51 Fit the scroll in the meat grinder
body with the thin metal
connection outwards, and press
firmly into place.
61 Fit the silicon coupling (15) onto
the scroll connection (see picture
6).
71 Fit the knife onto the scroll
connection (see picture 7). The
sharp edges of the knife should
point towards the meat screen.
81 Fit one of the three meat screens
on top of the knife (see picture
8). Turn the screen so one of the
depressions on the side align with
the round projection on the meat
grinder body.
o Select the meat screen for
the required consistency. You
can choose fine, medium and
coarse.
91 Fit the ring nut (11) over the meat
screen on the meat grinder body
(see picture 9). Turn clockwise to
lock. The ring nut must hold the
meat screen securely in place. But
do not over tighten.
111 Fit the meat tray (16) onto the meat
grinder body so that the wide
part is positioned over the motor section of the
appliance.
111 The appliance is now ready for use.
Grinding Meat
11 Cut your meat into smaller pieces, so the pieces fit
into the feeding tube. Dice or cut into strips with a
width of approx. 2.5 cm.
21 Put the pieces of meat onto the tray.
31 Place the mixing bowl or similar under the meat
grinder body opening.
41 Connect the appliance. The indicator next to the
OFF button lights up.
51 Start the appliance by pressing one of the five
speed buttons. Speed 1 is the slowest and speed
5 is the fastest. Recommended speeds, time and
capacity are shown in the table above.
61 The meat pieces travel down the feeding tube.
Push down carefully with the tamper (9). Do not
press too hard or you may damage the appliance.
71 Switch off the appliance by pressing the OFF
button when you have finished chopping. Always
unplug the appliance before you change the
accessories or take the appliance apart.
81 Dismantle the meat chopper by turning the body
slightly anti-clockwise and remove the body.
91 Fit the protective cover over the accessory socket
again.