Advertisement
Powering and initial cabling
Press the Power button on the back of the gateway. The Power indicator will initially flash GREEN to indicate that the gateway is booting and then solid GREEN
to indicate it is operational. Under normal operation, while the gateway is powering up, LED status is as follows:
• Broadband, WAN Ethernet, Wi-Fi and and Voice indicators will be off.
• Broadband indicator will initially be solid RED, and upon Ethernet link, it will light solid BLUE.
• Phone indicator will light solid GREEN after the Broadband indicator lights BLUE to indicate that digital phone service is active.
• Wireless indicator will light solid GREEN to indicate that the Wireless service is enabled.
NOTE: During the initial setup, it may take several minutes to achieve service connectivity.
Broadband: Follow instructions provided by your Service Provider. If no instructions are provided, then call your Service Provider.
Digital Phone Service: To connect the gateway to a digital phone line:
1. Connect the supplied RJ-11 terminated phone cable to the Phone port on the back of the gateway.
2. Connect the phone cable to a phone or fax machine.
LAN Ethernet: To make an Ethernet connection:
1. Connect the supplied RJ-45 terminated Ethernet cable to one of the Ethernet ports on the back of the gateway.
2. Connect the Ethernet cable to the Ethernet port on a local computer.
USB port: To connect the gateway to the USB port:
1. Connect the USB cable to the USB port on the back of the gateway.
2. Connect the other end of the USB cable to your device.
Access the Web Management Interface
1. Open a web browser, such as Firefox, Chrome, or Microsoft Internet Explorer, from the computer connected to the gateway.
2. Type the following address in the address bar of the browser to open the Access Code Required Screen:
http://192.168.1.254
NOTE: Select the appropriate language button in the lower right corner of the Access Code Required screen to continue with the selected language.
1. Provide the Device Access Code, a unique code printed on a label on the base of the gateway.
2. Select Continue.
To access the Web Management configuration pages:
Access Code Required
Page
NOTE: The terms Device Access Code and Password are sometimes used interchangeably.
Add a wireless device to the gateway
On the wireless device, use the Wireless setup option to find the available wireless network names. The Wi-Fi Network Name for the gateway is printed on
the bottom of the label along with the Wi-Fi password.
NOTE: The main page provides an overview about the connection and home network status. You can also access information for the following:
• Home: Network Status/Configuration
• System: System status, upgrade, restart and factory reset options
• Broadband: WAN status, statistics, and parameter settings
• Wi-Fi: Wi-Fi status and configuration
• Voice: Voice status and QoS configuration
• Home Network: LAN status and configuration
• Firewall: Firewall status/configuration
• Diagnostics: Gateway connection and application diagnostics
NOTE: This is a reference image and may slightly differ based on your device.
Declaration of conformity
The following sections describe regulatory compliance by region.
FCC/ISED compliance
This device has been tested and certified as compliant with the regulations and guidelines
set forth in the Federal Communication Commission - FCC Title 47 Part 15 and the
Innovation Science and Economic Development (ISED) Canada CAN ICES-3 (B)/NMB-3(B)
and RSS-247 Radio and Telecommunication regulatory requirements.
Cet appareil a été testé et certifié conforme aux réglementations et directives définies
dans les exigences réglementaires CAN CAN ICES-3 (B) / NMB-3 (B) et RSS-247 d'Innovation
et Canada (ISED).
Manufacturer: ARRIS
Models: NVG558H, NVG558CH
Part 15 of FCC rules
This device complies with part 15 of the FCC Rules and Industry Canada license- exempt
RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux normes CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes:
1. l'appareil ne doit pas produire de brouillage, et
2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
The device could automatically discontinue transmission in case of absence of information
to transmit, or operational failure. Note that this is not intended to prohibit transmission
of control or signaling information or the use of repetitive codes where required by the
technology.
The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems.
L'appareil peut interrompre automatiquement la transmission en cas d'absence
d'informations à transmettre ou de panne opérationnelle. Notez que ceci n'est pas destiné
à interdire la transmission d'informations de contrôle ou de signalisation ou l'utilisation de
Image: Home page
codes répétitifs lorsque cela est requis par la technologie.
Le dispositif utilisé dans la bande 5150-5250 MHz est réservé à une utilisation en intérieur
afin de réduire le risque de brouillage préjudiciable aux systèmes mobiles par satellite dans
le même canal.
Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement
pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux
systèmes de satellites mobiles utilisant les mêmes canaux.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by the party responsible for
compliance could void your authority to operate this equipment.
This radio transmitter 3439B-NVG5XDBAC has been approved by Innovation, Science
and Economic Development Canada to operate with the antenna types listed below,
with the maximum permissible gain indicated. Antenna types not included in this list
that have a gain greater than the maximum gain indicated for any type listed are strictly
prohibited for use with this device.
Cet émetteur radio 3439B-NVG5XDBAC a été approuvé par Innovation, Sciences
et Développement économique Canada pour fonctionner avec les types d'antenne
énumérés ci-dessous, avec le gain maximal autorisé indiqué. Les types d'antenne non
inclus dans cette liste et dont le gain est supérieur au gain maximal indiqué pour l'un
des types répertoriés ne sont strictement pas autorisés pour une utilisation avec cet
appareil.
Advertisement
