Canon PIXMA iP3000 Series Easy Setup Instructions

Canon PIXMA iP3000 Series Easy Setup Instructions

Canon pixma ip3000: setup instruction
Hide thumbs Also See for PIXMA iP3000 Series:

Advertisement

Quick Links

1

Unpack the Printer

1
Carefully remove all items from the box.
PIXMA iP3000 Series
Photo Printer
Documentation
and Software Kit
PIXMA iP3000 Series
Print Head
Power Cord
Ink Tanks
BCI-6C Cyan
BCI-6M Magenta
BCI-3eBK Black
BCI-6Y Yellow
2

Prepare the Printer

1
Remove the shipping tape from the
front and back of the printer.
2
Plug the power cord into the back of the
printer and connect the other end to a
power outlet. Press the POWER button.
The printer will initialize.
POWER
Lamp
POWER
Button
Lower the front cover. Raise the top cover.
3
Remove the shipping tape and lower the
inner cover.
Top Cover
Inner Cover
Front Cover
4
The print head holder automatically moves
to the center. Remove the protective tape.
Protective Tape
Serial Number
5
Write down the serial number located to
the right of the print head holder . You will
need this later to register the product.
Serial Number
Location

Start Here

Easy Setup Instructions
3

Install the Print Head

Remove the print head from its package.
1
Tear at notch to open
2
Remove the orange protective cap
from the print head.
NOTE: Do not touch the print head nozzles
and the electrical contacts.
Print Head Nozzles
Electrical Contacts
3
Raise the print head lock lever.
4
Slide the print head into the holder.
The print head will rest at a slight angle.
5
Lower the print head lock lever and press
it down until it clicks into place.
click
4

Install the Ink Tanks

1
Peel back the orange tab and completely
remove the plastic wrapper from the Yellow
Ink Tank (BCI-6Y).
2
Twist off and discard the orange protective cap.
NOTE: To avoid spilling ink, never press on the
sides of an ink tank.
Protective Cap
3
Insert the ink tank into the correct slot.
(Refer to the color guide on the print head holder).
Press down until the ink tank clicks into place.
click
4
Insert the remaining three ink tanks into
their assigned slots.
5
Close the inner cover, then the top cover.
Lift open the paper support and extend the
paper output tray.
Paper Support
Top Cover
Paper Output Tray
Inner Cover
NOTE: The printer will perform a print head
cleaning. Wait until the POWER lamp displays
a steady green light before proceeding.
iP3000
Series
Photo Printer
5
Connect the Printer
and Load Paper
IMPORTANT: Be sure the printer is
off before continuing, or the computer
will attempt to install the printer
driver before the printer is ready.
1
TURN THE PRINTER OFF.
2
Connect one end of the USB cable
to the computer, the other to the printer.
3
Remove the shipping tape from the paper
guide. Pinch the paper guide and slide it to
the left. Load a few sheets of blank paper
into the auto sheet feeder, then slide the
paper guide toward the left edge of the paper.
Auto Sheet
Feeder
Paper
Guide
Continue with Step 6
on side two.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PIXMA iP3000 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Canon PIXMA iP3000 Series

  • Page 1: Start Here

    Plug the power cord into the back of the printer and connect the other end to a power outlet. Press the POWER button. The printer will initialize. PIXMA iP3000 Series Photo Printer POWER Lamp Lower the front cover. Raise the top cover.
  • Page 2 Part no. QA7-3222-V01 © 2004 Canon U.S.A., Inc. Canon is a Registered Trademark of Canon Inc. All other products and brand names are registered trademarks or trademarks of their respective owners. Specifications subject to change without notice. P-iP3000-ESI-0304 Printed in Thailand.

Table of Contents