VIRTUFIT HTR 3.0i User Manual
  1. Manuals
  2. Brands
  3. VIRTUFIT Manuals
  4. Exercise Bike
  5. HTR 3.0i
  6. User manual

VIRTUFIT HTR 3.0i User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
HTR 3.0i Hometrainer
User manual
EN

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HTR 3.0i and is the answer not in the manual?

Questions and answers

Related Manuals for VIRTUFIT HTR 3.0i

Summary of Contents for VIRTUFIT HTR 3.0i

  • Page 1 HTR 3.0i Hometrainer User manual...
  • Page 2 TRAIN ON HEART RATE MAINTENANCE MAINTENANCE 18 - 19 TROUBLE SHOOTING TROUBLE SHOOTING 20 - 29 CONTROL PANEL CONTROL PANEL APP INSTRUCTIONS APP INSTRUCTIONS EXPLODED DRAWING EXPLODED DRAWING 32 - 33 PARTS LIST PARTS LIST TRAINING INSTRUCTIONS TRAINING INSTRUCTIONS VirtuFit HTR 3.0i Hometrainer...

  • Page 3: Safety Instructions

    0.5 metres of free space all around it. – Before using the device, check that the nuts and bolts are securely tightened. – The safety of the device can only be maintained if it is regularly examined for damage and/or wear and tear. VirtuFit HTR 3.0i Hometrainer...
  • Page 4 – Maintenance assembly and repair work not carried out by an official dealer. – In the event of improper use, neglect and / or poor maintenance. – Failure to maintain the device in accordance with the manufacturer’s instructions (see the enclosed manual). VirtuFit HTR 3.0i Hometrainer...
  • Page 5 Front support collumn Front support column Adjustment tube Power line Column lower plastic part Each 1 Adjustment tube Handle Power line NOTE! Do not connect the appliance to the power before it has been completely assembled. VirtuFit HTR 3.0i Hometrainer...
  • Page 6 R is the right), and pedals are mounted on the c cording to the direction of rotation shown in the figure, and lo d fixed. According to the label tip of the regulating tube, the maxi t is to STOP VirtuFit HTR 3.0i Hometrainer...
  • Page 7 There is a chance that you will damage the screw thread of this treadle so that the treadle can no longer ghten adjustment pull pin 33. (The height of the adjustment be put on it! NOTE! Tighten the pedals firmly! e adjusted by loosening adjustment pull pin 33, then pullin VirtuFit HTR 3.0i Hometrainer...
  • Page 8 Then mount the saddle (10) on the saddle post (13) as shown in figure (F). Secure the saddle with nuts, which can be attached to the sides. NOTE! According to the label on the seat post, the maximum height is when you should stop. VirtuFit HTR 3.0i Hometrainer...
  • Page 9 After fixing the front support column 12, install the plastic parts 40, 78 onto the plastic case of the main frame 1, make rubber cushion stuck between plastic case and front support tube, then lock by screws 76. VirtuFit HTR 3.0i Hometrainer...
  • Page 10 16 , and finally align the screw hole of the pper case 16 with the screw hole of the console rear cover 17, an VirtuFit HTR 3.0i Hometrainer...
  • Page 11 16. • Finally align the screw hole of the console upper case 16 with the screw hole of the console rear cover 17, and fasten and fix it with the screw 83. VirtuFit HTR 3.0i Hometrainer...
  • Page 12 First align the 18 column up plastic part R, 19 column lower plastic part L with the holes of the front • support column 12. • Then connect each other, and finally fasten them by screws 76. Explosive parts view VirtuFit HTR 3.0i Hometrainer...
  • Page 13 First align the 18 column up plastic part R, 19 column lower plastic part L with the holes of the front • support column 12. • Then connect each other, and finally fasten them by screws 76. tup completed: VirtuFit HTR 3.0i Hometrainer...
  • Page 14 • Inspect your hometrainer to make sure everything is tight and components are correct are mounted. NOTE! Switch off the power source if you will not be using the device for a long time! VirtuFit HTR 3.0i Hometrainer...

  • Page 15: Adjusting The Saddle

    Om de hometrainer te verplaatsen, druk het stuur naar beneden totdat de transportwielen aan de voorste stabilisator de grond raken. Met de transportwielen op de grond kunt u de hometrainer gemakkelijk naar de gewenste plek vervoeren. VirtuFit HTR 3.0i Hometrainer...
  • Page 16 HAND PULSE SENSORS Hand pulse sensors This VirtuFit fitness equipment is provided with hand pulse sensors for measuring the heart rate. The hand pulse sensors are located on the handlebars. The hand pulse sensors are only working if they are touched both at the same time for a couple of seconds.

  • Page 17: Daily Maintenance

    NOTE! Use a dry cloth to clean the control panel and areas around the power switch. Use a soft, clean cloth and detergent to remove stubborn stains and dirt from the hometrainer. VirtuFit HTR 3.0i Hometrainer...

  • Page 18: Troubleshooting

    • The sensors may become damp, dirty or greasy. So you have to clean them regularly. The console is not working If there is no signal when pedaling, check if the cable is properly attached. VirtuFit HTR 3.0i Hometrainer...

  • Page 19: Error Codes

    • If it cannot start, please replace the above EEPROM IC table. E81: Adjustment error • Switch on again. • Replace the cable puller. E82: Zeroing error • Switch on again. • Replace the cable puller. VirtuFit HTR 3.0i Hometrainer...

  • Page 20: Control Panel

    If this is, you as a user must ensure that the hand pulse sensors are held with both hands to start this test. PROGRAM Preset program. P01-P30: (Fixed programs), U01-U10: (Custom Programs), H01-H03: (Heart rate MANUAL programs), CONSTANT WATTS: (Energy controlled program). VirtuFit HTR 3.0i Hometrainer...
  • Page 21 Keep your hands on the sensor to display your heart rate or use a 5 kHz chest PULSE strap. Display range: 40 ~ 220. If no heart rate is detected during the exercise, the PULSE window will show “0”. WATT Displays the wattage. VirtuFit HTR 3.0i Hometrainer...

  • Page 22: Operation

    Press any key or pedal to wake up the display. • Each machine is equipped with a power adapter. If the machine screen does not display, please confirm that the power adapter is normal. VirtuFit HTR 3.0i Hometrainer...
  • Page 23 3. Press the MODE button to change the weight. The display will show “WEIG” and the window will flash “70”. Press +/- to change the weight. After the change is completed, press START / STOP to confirm and start the program, or press the MODE button to move to the next setting. VirtuFit HTR 3.0i Hometrainer...
  • Page 24 2. Press the MODE button to change the gender. The display shows “SEX”, and the window shows “0”, 0 blinks. Press the +/- button to change the gender. Male is 0, female is 1, after changing, press the MODE button to go to the next setting. VirtuFit HTR 3.0i Hometrainer...
  • Page 25 0:10 countdown, if no heart rate signal is received within 10 seconds, the PULSE window shows 0. After 10 seconds or by pressing the BODY FAT button you will return to the state before the BODY FAT mode was activated and you will hear two beeps. VirtuFit HTR 3.0i Hometrainer...
  • Page 26 18:00 (to indicate the time setting). Use the +/- button to change the time. Press the START button to confirm and start the program or select MODE to return to the first option to change the settings. VirtuFit HTR 3.0i Hometrainer...
  • Page 27 CONTROL PANEL PROGRAMS VirtuFit HTR 3.0i Hometrainer...
  • Page 28 CONTROL PANEL VirtuFit HTR 3.0i Hometrainer...
  • Page 29 CONTROL PANEL VirtuFit HTR 3.0i Hometrainer...

  • Page 30: App Instructions

    3. Scan the QR code on the right to go to the user manual of the app. The manual describes step by step how the app should be connected to the device, how the app works and what the options are. ZWIFT APP STORE GOOGLE PLAY USER MANUAL ZWIFT ZWIFT ZWIFT VirtuFit HTR 3.0i Hometrainer...

  • Page 31: Exploded Drawing

    EXPLODED DRAWING VirtuFit HTR 3.0i Hometrainer...

  • Page 32: Parts List

    Deep groove axle 6300 Slider Magnet resistance wheel φ280*51.5 Semicircular head hexagon M10*35 Inner clip spring Φ35 Belt wheel Φ260*T25 One-way axle 6003 Central axle set Inner spacer φ35*φ17*17 Motor Deep groove axle 6203 Adjustment tube reducer Small pulley VirtuFit HTR 3.0i Hometrainer...
  • Page 33 Flat washer M5 self- locking nuts M5 Flat countersunk head inner cross-flower self-tapping screw M3.5*12 Semicircular head inner cross-flower screw M4*12 Speed adjustment line Nylon washer M10 Rear foot tube Speed tester Heart rate piece Handle cap VirtuFit HTR 3.0i Hometrainer...

  • Page 34: Training Instructions

    The purpose of cooling down is to return the body to its normal or near normal, resting state at the end of each exercise session. A proper cool-down slowly lowers your heart rate and allows blood to return to the heart. VirtuFit HTR 3.0i Hometrainer...
  • Page 35 For questions or missing parts please contact your dealer.

Table of Contents